CS Paper Radar

Optimal TRACON Descent Procedures under Wind Uncertainty and Fuel Savings Factors

Yutian Pang, John-Paul Clarke

eess.SY ·submitted 2026-08-23 16:07 UTC · v1

Abstract

A terminal-area descent procedure need to perform across the wind climatology rather than a single wind condition. Although flight demonstrations of the delayed deceleration approach (DDA) showed substantial fuel savings, DDA combined late deceleration with a steeper $3.77^\circ$ final descent, obscuring the contribution of each design choice. In this work, we propose the continuous-descent delayed deceleration approach (CDDA), which applies delayed deceleration to a continuous descent approach (CDA) profile without a level segment before glideslope intercept. A simulation-based stochastic optimization selects flap deployment trigger speeds and glideslope-capture distance to minimize expected fuel under wind uncertainty subject to a given stabilized-approach probability. An optimal control reduction limits the design space to a few hundred candidates, enabling exact expectation over a weighted wind grid using six-degree-of-freedom fast-time simulations. CDA and CDDA are optimized at matched final angles of $3.00^\circ$, $3.50^\circ$, and $3.77^\circ$ for the A319, B737-800, B767-400, and A340-300. Results show that deceleration architecture is the weakest factor, yielding 0.3--3.9\% savings at $3.50^\circ$ and becoming material only for the B767-400 at $3.77^\circ$. Glideslope angle dominates fuel saving. At the $3.50^\circ$ Category D design maximum, optimized CDDA reduces expected fuel by 11-21\% relative to optimized $3^\circ$ CDA, while flap-schedule optimization adds 2-17\%. The DDA level segment acts primarily as a tailwind-robustness buffer, and the $3.77^\circ$ final exceeds the 1,000 ft/min stabilized-approach sink-rate element, limiting its near-term operational applicability.

Closest papers

Nearest neighbours by meaning across the whole index.

Trajectory-Based Co-Optimization of Arrival Scheduling and Descent Path Design in the Terminal Maneuvering Area

eess.SY ·2026-09-03 ·Yutian Pang, John-Paul Clarke
similarity 0.58
Abstract

Terminal arrival scheduling and descent procedure design are studied in two largely separate literatures. Scheduling models reduce each aircraft to a travel time and deliver target landing times, and fuel-efficient descent procedures are designed one aircraft at a time with the schedule taken as given, although both decide where an arriving aircraft absorbs delay before final approach. Existing formulations therefore cannot trade a slower, earlier-configuring descent against level track miles, a schedule that is efficient in time can be expensive in fuel, and autonomous or reduced-crew operations will need a single trajectory plan that ground automation and the flight management system both accept. To close this gap, we propose a four-dimensional terminal arrival scheduler that selects each aircraft's lateral path extension, glideslope-capture distance, and flap-deployment trigger speeds in one decision. We evaluate every candidate idle-thrust descent offline with a wind-aware backward plan and a six-degree-of-freedom forward simulation that returns descent time, fuel burn, minimum track length, and stabilized-approach feasibility, and a rolling-horizon scheduler commits one verified descent and one extension per aircraft under wake-separation constraints and observed entry winds. Two Atlanta terminal airspace case studies quantify the benefit. We show that co-optimized continuous descents save about 15\% of fleet fuel below saturation in a free-descent environment and that delayed deceleration saves about 23\%, while on the six published Runway 8L arrival flows the charted altitude floors remove 31\% of the design lattice and reduce the savings to 9--10\% and 20--21\%, respectively. We also find that wind moves single-aircraft descent fuel by 34--81\% yet explains at most 4\% of fleet fuel variance, because aircraft-specific wind effects average out across a scenario.

0.25

Statistical Turbulence and High-Fidelity Disturbance Fields for Quadrotor Flight Control

cs.LG physics.flu-dyncs.RO ·2026-09-09 ·Xun Huang
similarity 0.52
Abstract

Reinforcement-learning quadrotor controllers are usually trained under simplified wind models, yet the impact of wind-field fidelity, as opposed to magnitude, on policy robustness remains unquantified. This paper compares five disturbance-fidelity levels, from wind-free flight and discrete 1-cosine gusts through statistical turbulence and synthetic coherent structures to large-eddy-simulation fields of the atmospheric boundary layer, in a full cross-fidelity train test evaluation of proximal policy optimization (PPO) agents, with cascaded PID and geometric SE(3) controllers as training-free references, over a 0-12 m/s wind sweep. Before any controller comparison is made, all disturbance data are validated: every synthetic generator is checked quantitatively against its analytical or certification-standard reference, and the large-eddy-simulation fields against the imposed log law. On a racing-class quadrotor in hover, the train test matrix is remarkably flat, and the cheapest structured training wind, which is discrete-gust domain randomization, ranks first in every test column, a ranking replicated on a wind-sensitive 27 g platform; a once-tuned geometric controller brackets the learned PPO policies at zero crash rate. Mechanism diagnostics show that control authority, not wind realism, bounds robustness, so wind-fidelity investment should scale with platform wind sensitivity.

0.30

Extensions to the Dubins Airplane Method - Flight Performance Constraints in Uniform Wind

eess.SY ·2026-11-05 ·Simon Schopferer
top venue similarity 0.51
Abstract

This paper extends the Dubins Airplane Method to generate trajectories for fixed-wing aircraft that remain within flight performance limits in the presence of uniform wind. Within the field of runtime-efficient trajectory generation for fixed-wing aircraft, the Dubins Airplane Method represents a well-received and widely adopted compromise between algorithmic complexity, runtime efficiency, and solution quality. However, its simplistic kinematic model restricts its ability to generate safe and feasible trajectories, especially in the presence of wind. As a mathematical foundation to overcome these limitations, a set of closed-form equations are derived that relate flight performance constraints to kinematic constraints. Building upon existing methods that use trochoids for planning of 2D trajectories in uniform wind, this paper presents a set of iterative algorithms for planning versatile 3D trajectories composed of trochoidal or circular turns and straight flight segments, with constant vertical speed, constant thrust or smooth longitudinal transitions. The presented methods comprise a flexible and modular framework for runtime-efficient generation of performance-aware trajectories based on parametric curves without the need for numerical trajectory representations.

0.43

Controllability-Informed Distributed Electric Propulsion Aircraft Design Using Probabilistic Attainable Moment Sets

eess.SY math.OC ·2026-11-13 ·Umut Demir, Torbjørn Cunis, Aamir Ahmad, Walter Fichter
similarity 0.49
Abstract

Integrated aircraft design combines models of aerodynamics, propulsion, mass, and mission performance in one design loop, so that the disciplines can be traded against each other from the earliest stage. For configurations with distributed electric propulsion (DEP), part of the control authority comes from the propulsion system itself, which directly affects the required size of the tail and should therefore be known while the aircraft is being sized. This paper presents a controllability measure that is evaluated for every design in the loop and returned to it as a design signal. The attainable moment set of each candidate design is computed from the surrugate models of the loop and it is compared with a required moment set. Since the low-fidelity surrugate models are uncertain, the comparison is formulated with probabilistic attainable moment sets: the uncertainty is propagated to the boundary of the set, which yields a margin for every direction in the moment space and the probability of violating the requirement. The design loop thereby informed whether a configuration provides sufficient control authority, on which axes it falls short, and how this changes with the design variables. The approach is demonstrated on a DEP regional aircraft, where the signal is used to assess the size of the vertical tail.

0.24

LBA-CBF: Rapidly Adaptive Safety Filters via Parallel Dynamics Inference

cs.RO eess.SY ·2026-10-06 ·Maitham F. AL-Sunni, Timeea-Andreea Radu, Hassan Almubarak, Henry Z. Liao, Michael Görner +2 more
theorycode/data similarity 0.49
Abstract · 8 pages

Control barrier functions (CBFs) certify commands through an assumed dynamics model, so an abrupt, unmeasured regime change can undermine the certificate exactly when safety matters most. We present Look-Back Adaptive Control Barrier Functions (LBA-CBF), which rank a finite bank of candidate dynamics by recent prediction error over a short look-back window and enforce the high-order CBF condition against every model within a tolerance of the best, spanning best-fit adaptation to full-bank robust filtering. The dynamics may depend nonlinearly on the unknown parameters, and no switching model or continuously parameterized estimator is required. We prove that any feasible filtered input satisfies the true CBF condition whenever a safety-representative candidate is retained. In quadrotor simulation with abrupt wind reversals and an unknown payload, LBA-CBF is safe and reaches the goal from all random initial conditions, matching an oracle, while adaptive and robust baselines achieve 0-88% success. Banks of up to 250,000 models run inside the control loop, and Crazyflie 2.1 and F1TENTH experiments demonstrate adaptation to wind, payload release, and varying tire-road friction. Code, videos, and project details are available at: https://lla-control.github.io

0.59

Overcoming Fundamental Control Limitations in Powered Descent Flight through Robust Incremental Nonlinear Dynamic Inversion

eess.SY math.OC ·2026-11-05 ·João T. Diz, Paulo Rosa, Pedro Simplício, Paul Acquatella, Erik-Jan van Kampen +1 more
published similarity 0.49
Abstract · 28 pages, 16 figures, 5 tables. Accepted for presentation at the AIAA SciTech 2027 Forum, Orlando, FL, January 2027

This work identifies a fundamental, controller-independent limitation in reusable launch vehicle powered descent: a sudden $180^\circ$ phase transition in the open-loop transfer functions from the control inputs to the lateral drift and drift rate. The transition occurs inside the flight envelope, reverses the effective control direction, and can destabilize the closed loop system under uncertainty. An analytical condition governing this transition is derived, its physical mechanism is established, and its dependence on vehicle mass, aerodynamic properties, and geometry is characterized. An Incremental Nonlinear Dynamic Inversion (INDI)-based control architecture is then developed to inherently address this limitation and is tuned via $\mathcal{H}_\infty$ Closed Loop Shaping to provide local robustness and performance guarantees. The internal dynamics introduced by the INDI inversion are analytically derived and proven to be stable throughout the flight envelope. The proposed controller is compared against a robust gain-scheduled baseline controller through linear stability analysis and an extensive nonlinear Monte Carlo campaign. Both controllers achieve 100% success across the considered Monte Carlo campaign, though the INDI-based controller provides improved tracking performance, superior nominal and dispersed stability margins, requires fewer controller design points, and reduces controller tuning complexity.

0.45

Learned Warm Starts for Steady Transonic RANS Simulations of Wing and Aircraft Configurations

cs.CE physics.flu-dyn ·2026-10-31 ·Muhammad Irfan Zafar, Saleh Abuhanieh, Şahin Yiğit
similarity 0.49
Abstract

Neural surrogates can accelerate many-query aerodynamic analyses, but their standalone predictions may be insufficiently accurate or robust to support reliable design evaluations. We develop a learned warm-start formulation that predicts mean-flow and turbulence fields directly on native CFD meshes for subsequent correction by the RANS solver. A common architecture and objective structure are used across subcritical and transonic flows, including challenging conditions with shock-induced separation. A condition-modulated Transolver combines Fourier and wall features with target-gated regularization, a Sobolev-type loss, adaptive loss weighting and sampled training. Prediction requires no preliminary flow solution, and training requires no solver-residual evaluation. Extensive 3D CFD evaluations on SuperWing, the NASA Common Research Model (CRM) and DLR-F6 assess geometric and operating-condition generalization, including interpolation, extrapolation and cross-mesh deployment, using Spalart-Allmaras and $k$-$ω$ SST closures on million-cell meshes. Unseen nominal cases achieve geometric-mean iteration speed-ups of approximately $2$-$4\times$ under a common convergence criterion based on cold-run aerodynamic coefficients. On CRM, learned initialization provides greater aggregate acceleration than nearest-condition restarts using the same solution library. Resolution invariance enables direct deployment of coarse-mesh models on finer meshes without retraining, solution interpolation or target-condition coarse solves. Including data generation and training, estimated campaign speed-ups reach $2.1$-$2.3\times$. No warm run diverges; fewer than $2\%$ fail to satisfy the cold-reference convergence criterion. These results support learned initialization for repeated aerodynamic analyses, while highlighting initialization sensitivity near separation as a remaining limitation.

0.06

FlapSim: A Composable MuJoCo Simulation Platform and Reduced-Order Aerodynamic Model Hierarchy for Flapping-Wing Robotics

cs.RO ·2026-10-29 ·Mingshan He
code/data similarity 0.48
Abstract

Flapping-wing simulation need to reconcile high-frequency wingbeat aerodynamics with the slower dynamics relevant to flight control and reinforcement learning. We present FlapSim, a modular open-source MuJoCo simulation platform that combines robot descriptions, wing geometry, and composable aerodynamic models in a deterministic simulation pipeline. Across $48$ held-out scenarios spanning frequency, gimbal, wind, frequency-step, gust, and cross-robot flat-plate regimes, we compare five reduced-order configurations operating at $1\,\text{ms}$ with a $50\,μ\text{s}$ quasi-steady blade-element reference. The built-in hover cycle-averaged baseline achieves a $67.51\times$ CPU speedup but only $0.6593$ mean wrench fidelity. Combining multirate $21$-substep clock synchronization, three-dimensional linear/quadratic inflow and gust coupling, analytical blade-element geometry scaling, and phase-locked $1f\text{--}6f$ harmonics raises mean fidelity to $0.9646$ at a $65.19\times$ speedup in a five-block model. A streamlined four-block model without explicit step-transient lag states achieves $0.9662$ fidelity at a $67.98\times$ speedup. Controlled ablations show that stroke harmonics are particularly important during frequency transitions, improving held-out frequency-step fidelity by $+0.3176$. Transfer-function analysis explains this effect: fixed-window cycle averaging retains harmonic contributions when the wingbeat frequency changes, so within-cycle reconstruction also improves the filtered wrench. These results characterize the accuracy--computation tradeoff of the aerodynamic hierarchy and identify timing, inflow, geometry, and harmonic representation as central considerations for reduced-order flapping-wing simulation. The source code are available at: https://mingshanhe.github.io/FlapSim/\href{https://mingshanhe.github.io/FlapSim/}.

0.35