CS Paper Radar

Identification of $dq$-Asymmetric Impedances as Complex Transfer Functions Using a Single Arbitrary Excitation

Mohamed Abdalmoaty, Zheran Zeng, Dongsheng Yang, Florian Dörfler

eess.SP eess.SY ·submitted 2026-08-30 12:05 UTC · v1

Abstract

Cross-coupling between the $dq$ coordinates makes the identification of asymmetric grid impedances a challenging problem, particularly near the fundamental frequency where the asymmetric coupling is strongest. Existing schemes usually handle it either by perturbing the two coordinates sequentially, which lengthens the measurement, or by using a time-domain method with a global parametric model whose order must be tuned. This paper develops a single-shot active non-parametric frequency-domain method that avoids both. The equivalent impedance is parameterized by a pair of single-input single-output complex transfer functions. Each spectral line is fitted with a local rational model; the leakage and transient contributions are estimated, so that neither periodic steady-state excitation nor repeated excitation cycles are required. We give the exact finite-time discrete Fourier transform relation for the conjugate-coupled complex-signal model, and analyse the distortion that a stationary-frame filter placed ahead of the Park transform imposes on the identified pair. The method is validated on a controller hardware-in-the-loop platform against an analytically derived small-signal model, for a symmetric grid and for the same grid with an added grid-following converter that renders it asymmetric. Both complex transfer functions and all four real transfer functions of the $dq$ impedance are recovered over a wide band from a single one-second record of a random excitation, at 1 Hz resolution.

Closest papers

Nearest neighbours by meaning across the whole index.

Phase-Compensated Frequency-Scan Measurement of Harmonic Transfer Function Impedance

eess.SY ·2026-10-28 ·Yiyang Liao, Yitong Li, Jinjun Liu
similarity 0.61
Abstract

Impedance models obtained through frequency scanning provides terminal characterization for small-signal stability analysis without requiring detailed knowledge of internal converter parameters. When unbalanced steady-state components introduce cross-frequency coupling, conventional $2\times2$ impedance scan methods must be extended to identify harmonic transfer function (HTF) impedance. However, the measured phases of frequency-coupling terms depend on the starting time of the fast Fourier transform (FFT) window, potentially introducing phase errors when different time references are used. This paper presents a $dq$-domain measurement method of HTF impedance that explicitly accounts for this time dependence. Phase compensation aligns the measured Fourier coefficients to a common electrical phase reference, correcting the resulting phase discrepancies and enabling consistent impedance reconstruction. Comparisons with analytical models under balanced and unbalanced conditions verify the measurement method, recovering the conventional $2\times2$ impedance and the dominant coupling blocks of a $6\times6$ HTF representation, respectively.

0.34

Passive Identification of Unequal Phase Grid Impedances by Phase-Domain Source Cancellation

eess.SY ·2026-10-28 ·Songyang Zhang, Xun Gong, Bo Cao, Reza Iravani
similarity 0.58
Abstract

Passive grid impedance estimators that return a single resistance--inductance pair cannot represent a grid whose phase impedances are unequal. This paper identifies a separate pair for each phase from recorded point-of-common-coupling (PCC) voltage and current without injected perturbations. In each phase, the unknown grid-source voltage is cancelled by a periodic difference (PD) or by a second-order-generalized-integrator notch difference (SOGID), and moving-window integration (MWI) replaces the current derivative by an integral and an endpoint feature. The resulting two-parameter regression requires a period or notch-frequency estimate but no phase-locked-loop angle. A voltage-balance analysis gives the source residual left by frequency mismatch and bounds the parameter error by the ratio of this residual to the conditioning of the two features. In the unequal-phase interval (8.3--9.8~s) of a 10-s EMTP grid-forming record, SOGID-MWI attains phase-averaged R/L errors of 5.09/0.33\%; a shared value has a minimum error of 41.67\% for the phase ratio 1:0.5:2. On a 50-s constant-impedance grid-following record, the errors are 0.56/0.06\% over the 20--30-s synchronization disturbance. In a controlled 40-dB noise study, a noise-referenced update rule reduces the white-noise GFL error from 55.9/65.0\% to 12.3/11.5\%.

0.34

Frequency-Frame Covariance for Reactive-Power Scalarization

eess.SP eess.SYmath-ph ·2026-11-04 ·Kai Sun
similarity 0.56
Abstract

Measured voltage and current waveforms may be represented in a reference frame whose frequency differs from the physical fundamental frequency. Reactive-power readouts calculated from such frequency-shifted coordinates may change if their readout operators are not transformed consistently. This paper presents a frequency-frame covariance formulation for finite-spectrum, zero-mean periodic waveforms with complete harmonic information over one physical period. A necessary and sufficient covariance condition is derived, requiring the readout operator to transform consistently with the waveform representation. Consequently, frequency-dependent harmonic weights must be evaluated at physical harmonic orders rather than relative frame labels. In particular, the derivative/Iliovici readout equals a relative-derivative contribution plus an explicit reference contribution. The formulation also separates readout-operator errors from errors caused by changes in the physical components retained by waveform projections. Three analytical cases illustrate conditional carrier recovery for a memoryless resistor, physical-frequency weighting at relative zero in an RLC branch, and the possibility that an exact reactive-power scalar can coexist with a substantial waveform error after projection. The scope is deterministic calculation consistency in frequency-shifted coordinates rather than instrument measurement uncertainty.

0.13

A New Index for Quantifying Stability Adaptation Effort in Power Electronics-Dominated Power Systems Based on Frequency-Domain Impedance Identification

eess.SY ·2026-10-02 ·Luis A. Garcia-Reyes, Macarena Martin-Almenta, Edgar Nuño-Martínez, Javier Renedo, Antonio Cordón-Rodríguez +2 more
published similarity 0.53
Abstract · Paper in Proceedings of CIGRE Paris Session, C4-PS1, Paper ID 11553

The increasing use of converter based resources has made stability assessment in modern power systems more challenging, particularly because many devices are available only as black box models. Conventional eigenvalue based methods require full dynamic representations, while frequency domain impedance techniques based on the Generalized Nyquist Criterion (GNC) provide stability insight but do not quantify how much a converter must be retuned to restore stability. This paper introduces the Adaptation Effort Index (AEI), a metric that measures the sensitivity of dominant modes to parameter variations and quantifies the effort required for a converter to reconfigure itself under unstable operating conditions. The AEI combines the Nyquist Stability Margin obtained from frequency domain screening with a modal sensitivity index derived from fitted state space models synthesized from black box impedance data. The method is applied to a system comprising a grid forming and a grid following converter. Results show that, although both units can be tuned to stabilize the system, the grid following converter requires significantly less adaptation effort. The AEI therefore provides a practical and model agnostic tool for identifying which converter should be reconfigured in converter dominated grids, offering valuable guidance for system operators and manufacturers.

0.30

Equivalent DQ Sequence-Domain Model of Unbalanced Three-Phase Passive Elements for Power Converter Controllers

eess.SY ·2026-09-01 ·Air\án Franc\és, Luis Saz, Rafael Castillo, Dionisio Ramirez, Javier Uceda
publishedtheory similarity 0.52
Abstract · 8 pages, 7 figures, 2023 IEEE Applied Power Electronics Conference and Exposition (APEC)

Equivalent dq0 models of three-phase passive impedances are widely used for the design of three-phase inverter and rectifier controllers in the synchronous frame. However, these equivalent models assume that the impedance in each phase are the same, which is not always applicable. The fact that the impedance in each phase is different, generates second order harmonic content in the dq0 components, which hinders the advantages of the dq0 transformation. To avoid the second harmonic in these scenarios, it is possible to use the Fortescue's theorem to represent any asymmetrical set of three-phase signals as a linear combination of three symmetrical sequences. In the literature, only a few works have attempted to derive the equivalent model of unbalanced three-phase passive elements in the sequence domain, and none is able to account for the interaction between the zero sequence and the positive and negative sequences. This work presents the derivation of the equivalent dq sequence-domain model of unbalanced three-phase passive elements both analytically and with an intuitive graphical approach. Experimental results are shown to validate the proposed models.

0.72

Computing Scaled Relative Graphs of Discrete-Time LTI Systems: A Frequency-Domain Approach

eess.SY ·2026-09-29 ·Guoming Shi, Fredy Ruiz
similarity 0.51
Abstract

The scaled relative graph (SRG) represents the joint gain and phase properties of an input--output operator in the complex plane. This paper characterizes the SRG closure of causal, stable, square discrete-time linear time-invariant (LTI) systems on one-sided square-summable sequences. The Beltrami--Klein image of this closure equals the convex hull of the numerical ranges of the transformed frequency-response matrices. For real-coefficient single-input single-output systems, this yields the hyperbolic convex hull of the discrete-time Nyquist locus. The proof addresses the Hardy-space restriction imposed by one-sided inputs, which excludes persistent sinusoids, by replacing them with explicitly constructed finite-duration sinusoids. This construction shows how points in frequency-wise SRGs arise as limits of operator SRG points generated by admissible inputs. The characterization enables model-based computation of the closure from a state-space realization using frequency-response evaluations, numerical ranges, and planar convex hulls, without solving linear matrix inequalities.

0.51

Performance Limits and Tradeoffs of Power Systems Synchronization Recovery in Complex-Frequency Representation

eess.SY ·2026-10-02 ·Xiaoyu Peng, Zelin Sun, Zhongze Li, Feng Liu
theory similarity 0.51
Abstract

Power-system synchronization studies mainly ask whether synchronization can be achieved, whereas a complementary question is how well post-disturbance synchronization recovery can be shaped. In inverter-dominated systems, this recovery involves coupled phase-angle and voltage-magnitude dynamics, for which complex frequency provides a unified representation. This paper establishes a conservation law for synchronization recovery in this representation. For a given system and its initial state, the logarithmic integral of the proposed recovery residual is fixed by the initial contraction rate and the right-half-plane (RHP) zero--pole structure. Hence, synchronization recovery performance cannot be improved uniformly over frequencies and variables unless the budget set by these terms changes; controller tuning that preserves them can only redistribute the residual response across frequencies. The conservation law applies to both linear and nonlinear recovery responses satisfying the mild analyticity conditions. It further yields finite-frequency peak--bandwidth limits and a lower bound on the time-domain integral of squared complex frequency recovery. A system-level extension recovers classical Bode-type sensitivity conservation as an LTI special case. Studies on a heterogeneous IEEE 39-bus system verify the theory.

0.25

High-Order Sinusoidal Modeling for Precise Parameter Refinement

eess.SP eess.AS ·2026-10-15 ·Shaowen Chen, Tomoki Toda
unusual similarity 0.50
Abstract · This manuscript is currently under review for publication in the IEEE Transactions on Signal Processing. This work has been submitted to the…

Although the amplitude estimation of sinusoids is a linear and tractable problem when their frequencies are known, the accuracy of signal modeling is fundamentally limited by the inevitable frequency mismatches produced by existing methods. Quasi-harmonic modeling (QHM) and its extensions (aQHM and eaQHM) offer the ability to refine frequency estimates while extracting amplitudes; however, their extraction and correction capabilities remain limited. In this paper, we first revisit QHM methods from the perspective of frequency mismatches, and reveal that their performances are essentially constrained by the order of the model. Specifically, QHM methods are linear models and thus incapable of capturing higher-order frequency variations, leading to suboptimal modeling accuracy. Second, to address this limitation, we propose a higher-order modeling framework that enables more precise approximation of signal components. Eventually, we qualitatively characterize the optimization problem and employ the Levenberg--Marquardt (LM) algorithm for parameter estimation. As a result, the proposed method allows for significantly improved estimation of amplitudes, frequencies, and phases of sinusoidal components, enabling more accurate signal modeling. Experiments on both simulation study and speech signals demonstrate the superiority of the high-order model in frequency refinement and parameter extraction and its robustness under additive noise conditions.

0.24