CS Paper Radar

Finite Element Model Updating-based Load Rating of Bridges with Incomplete As-Built Information

Mehrdad S. Dizaji, Devin K. Harris, Mohamad Alipour, Abdou Ndong, Osman Ozbulut, Abdollah Bagheri

cs.CE ·submitted 2026-08-31 15:11 UTC · v1
unusual

Abstract

Load rating is the engineering process of determining the safe load-carrying capacity of an existing bridge structure often through analysis of its load-bearing members and their cross sections. However, when structural drawings and details of the structure are missing or insufficient for such calculations, alternative solutions must be used to infer the capacity. This study proposes a rational and consistent engineering solution for capacity inference based on structural identification (St-Id). The proposed approach uses finite element model updating (FEMU) to estimate the unknown characteristics of structures for use in an analytical load rating, which requires the development of an initial model developed in ABAQUS that can be updated based on experimental test data. ABAQUS allowed for the development of an interface with MATLAB, which facilitated the integration of an automatic iterative parameter optimization algorithm. The optimization algorithm developed in this investigation incorporated the features of a genetic algorithm (GA) and a gradient-based scheme to iterate on the unknown parameters. The proposed approach was evaluated on four in-service highway bridges including two concrete slab and two T-beam structures in varying deterioration condition states, which had sufficient plans available but were treated as having varying degrees of unknown details. The results illustrated that the finite element (FE) model updating approach generated load ratings that were within 0-17% of the target load ratings while alleviating the main challenges of the existing alternatives.

Comment
33, 18

Closest papers

Nearest neighbours by meaning across the whole index.

A Vehicle-Integrated Approach to Digital Twin Deployment for Bridges

eess.SP ·2026-09-25 ·Mehri Alamdari, Zihao Liu, Jiaji Wang, Kawabe Daigo, Chul Woo Kim
benchmark similarity 0.52
Abstract

The project A Vehicle Integrated Approach to Digital Twin Deployment for Bridges is developing a scalable framework for bridge condition assessment using vibration measurements from a sensorised inspection vehicle. It combines vehicle bridge interaction modelling, state estimation, machine learning and surrogate modelling to reduce reliance on permanent sensor networks. The Old Ada Bridge in Japan is the principal case study because it provides direct and vehicle-based field measurements across multiple experimentally introduced damage states. Progress has been made across three streams. First, forward and inverse Fourier Neural Operator (FNO) models have been demonstrated on a benchmark beam, enabling rapid response prediction and identification of damage location and severity. Second, an inspection vehicle optimisation framework has been developed to select vehicle mass and tyre suspension stiffness that maximise separation between healthy and damaged responses, integrating contact-point reconstruction, damage assessment, Kriging and particle swarm optimisation. Third, an Augmented Kalman Filter-based virtual sensing framework has been developed to estimate moving loads and reconstruct displacement, velocity and acceleration at unmeasured locations from sparse sensors. The next phase will extend and integrate these methods using the Old Ada Bridge model and field data. FNO models will be transferred to the truss structure and evaluated using intact and damaged measurements. Vehicle optimisation will be tested for transferability, while virtual sensing will be extended to the coupled vehicle bridge system to estimate road roughness, vehicle parameters, moving forces and structural responses. Ultimately, these components will form an integrated vehicle-driven digital twin for rapid simulation, response reconstruction and damage assessment under realistic conditions.

0.28

Generative AI-Driven Parametric Design Optimization Framework for Vehicle Closure Systems

cs.LG ·2026-11-16 ·Dongeon Lee, Yurim Lee, Jiyong Kim, Sanghyeon Kim, Sanghyun Lee +3 more
similarity 0.51
Abstract · 26 pages, 15 figures

This study presents a generative AI-driven parametric design optimization framework integrating performance-oriented generation with editable computer-aided design (CAD) and downstream computer-aided engineering (CAE) analysis for industrial vehicle closure systems. The framework is demonstrated on an automotive tailgate assembly with complex geometry, coupled components, and competing performance and feasibility requirements. A production-oriented CATIA model is restructured into a reference-based parametric template with a 13-dimensional design representation. An automated CAD/CAE workflow generates parametric models, performs structural analysis, and constructs a database of mass, maximum displacement, and maximum von Mises stress. Gaussian process regression surrogates predict performance, while diffusion and flow matching models generate design candidates. The design problem minimizes mass and maximum displacement, with stress assessed as an engineering feasibility constraint. Performance-guided generation using surrogate guidance and performance-aware training using a performance-aware loss incorporate engineering objectives, with sensitivity to guidance scale and loss weight evaluated. Generative search is compared with NSGA-II under matched evaluation budgets using a common surrogate model. Selected Pareto-region candidates are reconstructed in CATIA and re-evaluated through native CAE; all verified candidates are successfully regenerated and analyzed. Relative to the baseline, the knee-point design reduces mass by 7.1% and maximum displacement by 29.4%, while extreme verified solutions achieve maximum reductions of 10.3% and 37.3%, respectively. The results demonstrate performance-oriented multi-objective design exploration compatible with editable industrial CAD and native engineering verification.

0.30

MiDShip: Multimodal Dataset of Ship Cargo Hold Structures for Engineering Design

cs.CE cs.LG ·2026-09-04 ·Noah J. Bagazinski, Md. Ferdous Alam, Jaya Manideep Rebbagondla, Faez Ahmed
similarity 0.49
Abstract

Ship structures govern vessel strength, safety, and manufacturability, but their design must satisfy hundreds of classification society requirements, making the process complex and iterative. Data-driven approaches are limited by the lack of structured datasets linking design geometry, structural performance, and rule-based constraints. This paper presents MiDShip, a multimodal dataset of 12,753 synthetic cargo-hold structural designs: 6,020 random, 496 generated by an SGLD-inspired procedure, and 6,237 generated by an equation-informed repair procedure. Each design includes parametric data, full and mesh-ready 3D geometry, engineering drawings and annotations, a bill of materials, and preliminary structural evaluations. Twenty-five constraints derived from a subset of ABS MVR are also evaluated. None of the random designs satisfies all constraints. Among the SGLD-inspired designs, 322 (64.9%) were fully compliant, with an average of 0.409 violations, 82.7% below the seed mean and 96.9% below the random-design mean. The repair procedure, developed through LLM-assisted code analysis, produced 4,952 fully compliant designs (79.4%), averaging 0.296 violations, 97.1% below the paired-source mean. In equal-size comparisons, mean nearest-neighbor distances in the scaled 120-parameter space were 3.495 for repaired designs, 1.144 for SGLD batches, and 3.729 for random designs. The primary contribution is the synchronized dataset and its generation and evaluation infrastructure; the generation studies demonstrate its utility rather than proposing new optimization algorithms. MiDShip supports machine learning, generative design, and automated rule-based evaluation for ship structures.

0.24

Reliability Assessment of FRP-RC Columns Using AK-MCS with a Piecewise Two-Branch Approach

cs.CE stat.APstat.CO ·2026-10-25 ·Arndt Goldack, Richard Koehler, Ahmed Usama Syed
similarity 0.48
Abstract · 22 pages, 5 figures

Slender concrete columns reinforced with fiber-reinforced polymer (FRP) bars fail at medium to high axial load levels either by concrete crushing or by loss of stability, while the tensile strains in the reinforcement remain far below the rupture strain. Each non-linear finite element (FE) analysis yields only the capacity of the governing failure mode, and the governing mode changes over a broad zone in which both capacities are nearly equal. Both characteristics conflict with active-learning Kriging-assisted Monte Carlo simulation (AK-MCS), which assumes a single, smooth limit-state function. This paper proposes a piecewise, two-branch AK-MCS framework in which each failure mode is represented by its own Kriging model, trained only on the FE analyses in which that mode governs, and the governing prediction is the minimum of both. Safeguards against data starvation keep rarely governing branches usable. After convergence, additional FE analyses are placed based on a leave-one-out calibration check and on the width of the confidence interval on the reliability index. A design-point search on the surrogate and importance sampling at the design points provide the reliability index even where direct Monte Carlo simulation finds no failure. For an FRP-reinforced concrete column example with mixed failure, 79% and 62% of the training points lie near the mode boundary. The reliability index from the design-point search agrees with the Monte Carlo estimate to within 0.05, and an FE analysis at the design point confirms the surrogate to within 0.6%.

0.29

Life-cycle structural reliability of RC bridge piers under corrosion in a changing climate

cs.PF ·2026-11-16 ·Giuseppe Vittorio Nava, Luca Capacci, Fabio Biondini, Lorenzo Casti
publishedunusualhighly cited similarity 0.46
Abstract

Aging and deterioration processes of structures and infrastructure systems can be severely affected by the long-term evolution of environmental conditions expected in a changing climate. This paper aims at investigating the interaction between climate change and environmental aggressiveness on the probabilistic life-cycle performance of concrete structures under corrosion. A simulation-based framework is proposed for life-cycle structural reliability analysis under climate change scenarios. The framework is applied to a bridge pier with hollow core cross-section exposed to chloride-induced corrosion. The results allow to quantify the impact of climate change on long-term probabilistic structural response and highlight the need for proper modeling of the environmental parameters and climate evolution over the entire lifespan of aging structures for optimal life-cycle maintenance and management of structural and infrastructural facilities.

0.59

A Physics-informed Neural Network Approach for Robust Buckling Load Prediction and Reliability-Based Design of Thin Truncated Conical Shells

cs.LG ·2026-08-22 ·Devasmit Dutta, Budhaditya De, Rohan Majumder, Sudip Kumar Mishra
similarity 0.45
Abstract

Thin-walled truncated conical shells are widely used in aerospace, marine, offshore, and lightweight infrastructure systems due to their high strength-to-weight ratio and geometric efficiency. Their buckling resistance under axial compression, however, is highly sensitive to geometric imperfections, manufacturing tolerances, material variability, and nonlinear instability effects. Conventional design procedures rely on conservative knockdown factors (KDFs), such as those recommended in NASA SP-8019, which do not explicitly account for shell geometry, fabrication quality, data uncertainty, or target reliability. This study develops a physics-informed neural network (PiNN) framework for predicting critical buckling loads of thin truncated conical shells and integrates the trained surrogate within a reliability-based design (RBD) formulation. The model combines geometric and material descriptors with mechanics-informed features derived from shell stability theory and the localized reduced stiffness method (LRSM). A physics-informed loss function penalizes mechanically inadmissible predictions exceeding the theoretical elastic buckling load. The framework is trained and evaluated using 133 experimental Mylar conical shell tests under axial compression. Compared with a conventional deep neural network (DNN), the PiNN improves predictive accuracy, reduces mean absolute error, and enhances physical consistency. The trained PiNN is then used to evaluate reliability indices and calibrate safety-consistent KDFs for prescribed target reliability levels. Results demonstrate that the PiNN-RBD framework provides an efficient approach for uncertainty-aware design of imperfection-sensitive shell structures.

0.49

Closed-loop AI achieves certifiable engineering design

cs.AI ·2026-08-22 ·Tianyi Yu, Chengxing Tao, Haoxuan Shen, Huiyang Li, Rugang Chen +6 more
similarity 0.45
Abstract · 24 pages,3 figures

Agentic AI has automated parts of scientific discovery, including paper generation, expert-level coding, therapeutic proposal, and autonomous experimentation. Complex physical engineering design remains a gap, because candidates must satisfy simultaneous constraints in fluid dynamics, solid mechanics, and structural stability. We introduce The AI Engineer, an agentic framework that couples large language models (LLMs) to deterministic engineering backends in a closed loop: natural-language requirements are converted into design-domain geometry and mesh; topology is optimized with bi-directional evolutionary structural optimization (BESO) coupled to the CalculiX solver; and member sizes are refined with particle swarm optimization (PSO) coupled to Zwind under offshore aero-hydro-servo-elastic load cases. To explore many designs without per-candidate certification cost, an Automated Reviewer scores each candidate on five dimensions (capacity, steel intensity, unit cost, constructability, and fatigue life) using piecewise-linear functions calibrated on 11 real floating-wind projects. Search terminates only when a candidate reaches a composite score $S \ge 85$ (grade A) with no subscore below 60. We validated this gate by submitting the top-scoring design to the China Classification Society (CCS) for Approval in Principle (AIP), which it passed; AIP is thus an external check that the reviewer tracks professional judgment, not the daily objective. The certified design outperforms the human-optimized TuQiang baseline, reducing steel mass and unit capital cost by 8.1% each while meeting all AIP criteria. This verification-closed regime, in which every proposal is judged by deterministic physics and codified limit states, distinguishes The AI Engineer from open-ended generative systems. Remaining limits include detailed design and fabrication-hard constraints.

0.30

Modeling and Generative-AI-Based Design of Load-Adaptive Gravity Balancing Mechanisms

cs.RO ·2026-09-25 ·Ryotaro Kayawake, Kazuki Abe, Shota Miyake, Masahiro Watanabe, Kenjiro Tadakuma
similarity 0.45
Abstract · 13 pages, 9 figures. To be submitted to the Journal of Mechanical Design

Load-adaptive gravity balancing mechanisms (LA-GBMs) can accommodate various loading conditions by passively changing their characteristics in response to payload variations. However, their design is difficult because both the desired mechanism motion and static equilibrium under variable payloads must be satisfied simultaneously. This study proposes a general design methodology for LA-GBMs that does not depend on specific mechanism architectures or mechanical elements. The necessary conditions for the potential fields of LA-GBMs are formulated, and two general forms are derived: an affine form representing the effect of payload mass and a factorized form representing state transitions associated with load adaptation and gravity balancing. These forms are then provided to generative AI as design requirements to generate candidate potential functions. The generated functions are analytically verified in terms of their conformity to the two general forms and the conditions required for valid LA-GBMs. Furthermore, the obtained potential functions are decomposed into individual terms, and an example of a method for constructing an LA-GBM by combining springs, counterweights, and function-generating linkage mechanisms is presented. By using potential functions as an intermediate representation, the proposed framework enables the generation of LA-GBM design candidates without prescribing a mechanism architecture in advance. Mechanical realizability and manufacturability of the generated potential fields remain important issues for future work.

0.28