CS Paper Radar

Modeling and Generative-AI-Based Design of Load-Adaptive Gravity Balancing Mechanisms

Ryotaro Kayawake, Kazuki Abe, Shota Miyake, Masahiro Watanabe, Kenjiro Tadakuma

cs.RO ·submitted 2026-09-25 15:18 UTC · v1

Abstract

Load-adaptive gravity balancing mechanisms (LA-GBMs) can accommodate various loading conditions by passively changing their characteristics in response to payload variations. However, their design is difficult because both the desired mechanism motion and static equilibrium under variable payloads must be satisfied simultaneously. This study proposes a general design methodology for LA-GBMs that does not depend on specific mechanism architectures or mechanical elements. The necessary conditions for the potential fields of LA-GBMs are formulated, and two general forms are derived: an affine form representing the effect of payload mass and a factorized form representing state transitions associated with load adaptation and gravity balancing. These forms are then provided to generative AI as design requirements to generate candidate potential functions. The generated functions are analytically verified in terms of their conformity to the two general forms and the conditions required for valid LA-GBMs. Furthermore, the obtained potential functions are decomposed into individual terms, and an example of a method for constructing an LA-GBM by combining springs, counterweights, and function-generating linkage mechanisms is presented. By using potential functions as an intermediate representation, the proposed framework enables the generation of LA-GBM design candidates without prescribing a mechanism architecture in advance. Mechanical realizability and manufacturability of the generated potential fields remain important issues for future work.

Comment
13 pages, 9 figures. To be submitted to the Journal of Mechanical Design

Closest papers

Nearest neighbours by meaning across the whole index.

Task-Distribution-Aware Counterweight Synthesis and Constrained Co-Design for Serial Manipulators

cs.RO cs.LG ·2026-09-14 ·Mohammad Abbadi
similarity 0.56
Abstract · 9 pages, 6 figures

Passive counterweights are simple gravity compensators, but a counterweight selected from a single pose is not generally optimal for the configurations and tasks a manipulator actually executes. This paper develops a task-distribution-aware synthesis framework in which the operating distribution $ρ(q)$ enters the design explicitly. For a counterweight moment $p=m_c r_c$ with gravity torque $-gpφ(q)$, the weighted mean-square residual gravity torque has the closed-form minimizer $p^*=E_ρ[τ_gφ]/(gE_ρ[φ^2])$. If payload gravity torque is affine in payload mass, the optimum is also affine: $p^*(m_p,ρ)=p_0^*(ρ)+m_pK_p(ρ)$. For fixed static moment, added counterweight inertia is $I_c=pr_c$ while mass is $m_c=p/r_c$, so mass-radius selection is underdetermined unless physical constraints are specified. A recovered three-link manipulator is used as a case study. At $r_c=0.20$ m, zero-payload equivalent optima are 0.672 kg for uniform joint-space operation, 0.683 kg for approximately uniform task-space operation, 0.713 kg for a representative pick-and-place family, and 0.952 kg for a high-gravity-biased distribution, a change of more than 40% caused solely by the operating distribution. Nondominated fronts show that preferred mass-radius pairs depend on declared engineering bounds. A rated-torque-referenced all-joint screen increases zero-payload feasible task-space coverage from 78.1% without compensation to 93.7% for the uniform-distribution design. A lumped point-mass trajectory study gives a provisional crossover from no counterweight at very aggressive motion to stronger compensation as motion slows. These actuator and dynamic results are engineering consequence studies rather than physical validation.

0.30

Total Energy Shaping of Underactuated Systems via Gravity Compensation at the Desired Equilibrium

eess.SY ·2026-11-12 ·M. Reza J. Harandi, Mehrzad Namvar
similarity 0.56
Abstract

This paper investigates total energy shaping of underactuated mechanical systems with gravity compensation evaluated at the desired equilibrium instead of throughout the online closed-loop operation. Within the interconnection and damping assignment passivity-based control (IDA-PBC) framework, sufficient conditions for local asymptotic stability are established in terms of integrability of a vector field and positive definiteness of an augmented potential energy. The approach is also combined with a reformulation of potential energy matching that replaces a nonhomogeneous partial differential equation with a homogeneous one and introduces an additional design term. Analytic constructions for the TORA system and a class of two-degree-of-freedom systems illustrate how the matching and integrability requirements can be addressed. The proposed control law avoids online evaluation of the configuration-dependent gravity term; offline controller synthesis and verification can still require knowledge of the gravity model.

0.31

Transporting Unsecured Stacked Payloads with a Quadrupedal Robot via Multi-Objective Reinforcement Learning

cs.RO cs.LG ·2026-10-05 ·Nobuo Namura, Masayuki Hiromoto, Kento Uemura, Hironobu Sasaki, Kanata Suzuki
hot direction similarity 0.49
Abstract · 8 pages, 6 figures

Transporting unsecured payloads with legged robots over uneven terrain requires balancing locomotion performance and payload stability, since aggressive motion can destabilize the payload even when the robot remains stable. We study quadrupedal transportation of unsecured stacked boxes on an edgeless torso-mounted board without dedicated payload sensors or active carrier mechanisms. To address this trade-off, we propose Payload-Adaptive Multi-Objective Reinforcement learning for Transportation (PAMORT). PAMORT trains a multi-objective base policy conditioned on a preference vector that weights locomotion and payload-stability reward groups, then trains a weight adjuster on the frozen policy to adapt this preference online from proprioception. In simulation, PAMORT achieves comparable or better overall transportation success than a corresponding single-objective baseline across different payload configurations, including an unseen three-box stack, despite training only with two boxes. Real-world experiments on a Unitree Go2 demonstrate zero-shot transfer to slopes and steps at or beyond the training difficulty, with mean success rates of 0.850 for PAMORT and 0.675 for the baseline across eight tasks. These results demonstrate robust unsecured-payload transportation with online adaptation of the locomotion--payload trade-off from proprioceptive information.

0.26

Task-Oriented Co-Design and Optimization of Geared Actuators for Robotic Applications

cs.RO ·2026-09-19 ·Xuanyu Huang, Jianqiang Dong, Hang Zhao
hot direction similarity 0.47
Abstract

Different tasks performed by legged robots impose distinct torque and speed requirements on actuators. Existing robotic actuators are generally optimized at the component level for metrics such as torque or power density, without explicit task guidance. System-level optimization across components such as motors, gearboxes, and sensors is challenging because of the high computational cost and coupling among mechanical, electrical, and electromagnetic behaviors. Consequently, improvements in individual components may not translate into better robot performance in a specific task. To this end, we present a systematic optimization framework for task-oriented co-design of actuator hardware and control. First, surrogate models are employed to accelerate motor evaluation and support global exploration of the coupled design space. Then, a hierarchical mixed-variable optimization strategy is adopted, combining discrete enumeration with continuous search over dimensions and real-valued indices. These indices are rounded to select admissible values for the remaining discrete choices before each evaluation. Within this search, rated output torque density and task performance are jointly optimized, with Bezier-parameterized joint torque profiles determined for each hardware candidate. Finally, the effectiveness of the proposed framework is validated through actuator fabrication and experiments on a two-degree-of-freedom jumping leg. Based on its measured mass, the fabricated prototype achieves a nominal rated output torque density of 35.7 N m/kg, approximately 60% higher than that of a widely used commercial geared joint actuator, while being 18.6% lighter. Under matched bench conditions, it achieves 12.0% greater jump height at twice-rated torque. Together, these results demonstrate a systematic route from task requirements to actuator design and control.

0.36

Systematic Lightweight Method for Robotics Based on Strain Energy Distribution Optimization

cs.RO ·2026-08-29 ·Jingchen Li
similarity 0.47
Abstract

Service robots work with people and are highly expected to be lightweight for safety, agility and energy conservation. As a complex mechanical system, a robot consists of a large number of components and has various working configurations and load environments. An effective method for achieving system-level optimal robot design is a crucial requirement, but it poses significant challenges. In this study, we introduce a novel approach to optimize the distribution of strain energy, which can significantly improve the effectiveness of systematic optimization in a complex system. First, we present and demonstrate that the strain energy per unit mass should be uniformly distributed in an optimal lightweight mechanical system. Based on this criterion, the system-level problem can be decoupled and the design objective of each part can be assigned based on the strain energy. Then, each part can be optimally designed separately according to its specific circumstances by using different approaches, such as size optimization, topological optimization, and material optimization. In this way, the optimization is at the system level, while the computational complexity is at the part level. Weight reduction and improvements in mechanical properties can be obtained simultaneously. As an example, this method is applied to an arbitrarily designed robotic arm, and its effectiveness is further demonstrated in the cases of lightweight with stiffness improvement, considering multiple materials, multiple working conditions, and vibration performance.

0.43

A Bi-level Co-design Framework for Lunar Monoped with 2D Jump and Landing Control

cs.RO eess.SY ·2026-10-27 ·Sanjay Ramkumar, Suraj Kumar
similarity 0.47
Abstract · 8 pages, 13 figures

Legged robots for lunar exploration must be designed for low gravity, where reduced contact forces and long flight phases make leg morphology and controller choice interdependent. We study this for a planar monoped in lunar gravity ($1.625$ m/s$^2$) using a bi-level co-design framework: a differential evolution outer loop searches over link lengths, and each candidate is evaluated on a vertical jump by either a quadratic program based task-space controller (QP-TSC) or a direct-collocation based trajectory optimization. The two controllers yield different optimal link lengths, and trajectory optimization outperforms the QP-TSC across most of the design space, with 17% lower Cost of Transport (COT) at their respective optima. We then extend to a 2D jump, where trajectory optimization with centroidal angular momentum regulation produces stable in-place and forward jumps, and an LQR controller absorbs impact and stabilizes the robot after touchdown. This is demonstrated on a baseline morphology with both links 0.3 m long.

0.17

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.47
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14

Compositional Aeroelastic Operators for Morphing Flexible Multibody Aircraft: A Geometric Framework with Structural Verification

cs.CE math.NAphysics.flu-dyn ·2026-08-15 ·Gelin Chen, Chen Song, Chao Yang
similarity 0.46
Abstract · 30 pages, 2 figures, 2 tables

Morphing flexible multibody aircraft require structural strain, aerodynamic geometry, surface velocity, and generalized loading to remain compatible as joints and flexible components change configuration. A compositional formulation is developed around an assumed material attachment between each lifting surface and a geometrically exact beam. Separating the component root pose from the section field shows that the body strain and elastic potential of a component depend on its own elastic coordinates, while upstream motion enters kinetic terms and external-load pullbacks. At element level, an exact relative logarithm $d$ supplies strain and potential energy, whereas a reference-anchored section coordinate $σ$ supplies deformed section geometry. Finite-order expansions retain the finite reference geometry exactly and truncate only endpoint perturbations. The attachment map then generates surface points, tangents, normals, velocities, and force Jacobians from common section kinematics. Euler--Poincare beam balance, moving-surface potential-flow relations, graph cotangent assembly, and the associated semidiscrete power identity are stated in a common twist--wrench convention. Collocation, pressure, equivalent-load, and structural-station sites are distinguished to expose their approximation errors. Verification gives the expected $N_d+1$ convergence order for degree-$N_d$ relative-log expansions. In a geometrically nonlinear cantilever comparison, a cubic static-manifold correction reduces mean full-record displacement error from $0.479$ to $0.255$ over four completed load cases. These results provide structural and interface-level evidence rather than validation of a complete aircraft aeroelastic prediction.

0.10