CS Paper Radar

Task-Distribution-Aware Counterweight Synthesis and Constrained Co-Design for Serial Manipulators

Mohammad Abbadi

cs.RO cs.LG ·submitted 2026-09-14 05:51 UTC · v1

Abstract

Passive counterweights are simple gravity compensators, but a counterweight selected from a single pose is not generally optimal for the configurations and tasks a manipulator actually executes. This paper develops a task-distribution-aware synthesis framework in which the operating distribution $ρ(q)$ enters the design explicitly. For a counterweight moment $p=m_c r_c$ with gravity torque $-gpφ(q)$, the weighted mean-square residual gravity torque has the closed-form minimizer $p^*=E_ρ[τ_gφ]/(gE_ρ[φ^2])$. If payload gravity torque is affine in payload mass, the optimum is also affine: $p^*(m_p,ρ)=p_0^*(ρ)+m_pK_p(ρ)$. For fixed static moment, added counterweight inertia is $I_c=pr_c$ while mass is $m_c=p/r_c$, so mass-radius selection is underdetermined unless physical constraints are specified. A recovered three-link manipulator is used as a case study. At $r_c=0.20$ m, zero-payload equivalent optima are 0.672 kg for uniform joint-space operation, 0.683 kg for approximately uniform task-space operation, 0.713 kg for a representative pick-and-place family, and 0.952 kg for a high-gravity-biased distribution, a change of more than 40% caused solely by the operating distribution. Nondominated fronts show that preferred mass-radius pairs depend on declared engineering bounds. A rated-torque-referenced all-joint screen increases zero-payload feasible task-space coverage from 78.1% without compensation to 93.7% for the uniform-distribution design. A lumped point-mass trajectory study gives a provisional crossover from no counterweight at very aggressive motion to stronger compensation as motion slows. These actuator and dynamic results are engineering consequence studies rather than physical validation.

Comment
9 pages, 6 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Task-Oriented Co-Design and Optimization of Geared Actuators for Robotic Applications

cs.RO ·2026-09-19 ·Xuanyu Huang, Jianqiang Dong, Hang Zhao
hot direction similarity 0.57
Abstract

Different tasks performed by legged robots impose distinct torque and speed requirements on actuators. Existing robotic actuators are generally optimized at the component level for metrics such as torque or power density, without explicit task guidance. System-level optimization across components such as motors, gearboxes, and sensors is challenging because of the high computational cost and coupling among mechanical, electrical, and electromagnetic behaviors. Consequently, improvements in individual components may not translate into better robot performance in a specific task. To this end, we present a systematic optimization framework for task-oriented co-design of actuator hardware and control. First, surrogate models are employed to accelerate motor evaluation and support global exploration of the coupled design space. Then, a hierarchical mixed-variable optimization strategy is adopted, combining discrete enumeration with continuous search over dimensions and real-valued indices. These indices are rounded to select admissible values for the remaining discrete choices before each evaluation. Within this search, rated output torque density and task performance are jointly optimized, with Bezier-parameterized joint torque profiles determined for each hardware candidate. Finally, the effectiveness of the proposed framework is validated through actuator fabrication and experiments on a two-degree-of-freedom jumping leg. Based on its measured mass, the fabricated prototype achieves a nominal rated output torque density of 35.7 N m/kg, approximately 60% higher than that of a widely used commercial geared joint actuator, while being 18.6% lighter. Under matched bench conditions, it achieves 12.0% greater jump height at twice-rated torque. Together, these results demonstrate a systematic route from task requirements to actuator design and control.

0.36

Modeling and Generative-AI-Based Design of Load-Adaptive Gravity Balancing Mechanisms

cs.RO ·2026-09-25 ·Ryotaro Kayawake, Kazuki Abe, Shota Miyake, Masahiro Watanabe, Kenjiro Tadakuma
similarity 0.56
Abstract · 13 pages, 9 figures. To be submitted to the Journal of Mechanical Design

Load-adaptive gravity balancing mechanisms (LA-GBMs) can accommodate various loading conditions by passively changing their characteristics in response to payload variations. However, their design is difficult because both the desired mechanism motion and static equilibrium under variable payloads must be satisfied simultaneously. This study proposes a general design methodology for LA-GBMs that does not depend on specific mechanism architectures or mechanical elements. The necessary conditions for the potential fields of LA-GBMs are formulated, and two general forms are derived: an affine form representing the effect of payload mass and a factorized form representing state transitions associated with load adaptation and gravity balancing. These forms are then provided to generative AI as design requirements to generate candidate potential functions. The generated functions are analytically verified in terms of their conformity to the two general forms and the conditions required for valid LA-GBMs. Furthermore, the obtained potential functions are decomposed into individual terms, and an example of a method for constructing an LA-GBM by combining springs, counterweights, and function-generating linkage mechanisms is presented. By using potential functions as an intermediate representation, the proposed framework enables the generation of LA-GBM design candidates without prescribing a mechanism architecture in advance. Mechanical realizability and manufacturability of the generated potential fields remain important issues for future work.

0.28

Real-Time Dynamics-Based Torque-Sampling MPPI for Compliant and Force Aware Manipulation

cs.RO ·2026-09-02 ·Euncheol Im, Taehyun Kim, Yonghwan Oh, Myotaeg Lim, Yisoo Lee
published similarity 0.54
Abstract · 8 pages, 6 figures. Accepted to the IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2026)

This study proposes a novel Model Predictive Path Integral (MPPI)-based task-space control framework. The proposed framework explicitly solves rigid-body dynamics within a real-time MPC formulation and enforces safety constraints, enabling accurate motion and force control that yields compliant behaviors for safe and effective physical interaction of robotic manipulators in unstructured environments. By leveraging MPPI, the proposed framework efficiently handles nonlinear dynamics that are difficult to solve with conventional MPC approaches in real-time. Furthermore, we develop a torque-sampling-based control architecture that enables efficient exploitation of GPU-based parallelization, resulting in effective compliant and force-aware behaviors. As a result, the proposed framework achieves a solver update rate of over 166 Hz with a 0.18 s prediction horizon, and its performance is validated through real-world experiments on a 7-DoF manipulator.

0.38

Structure-Actuation Co-Design of All-Electric Heavy-Duty Robotic Manipulators

cs.RO eess.SY ·2026-10-27 ·Mohammad Bahari, Amir Hossein Barjini, Jouni Mattila
benchmark similarity 0.53
Abstract · 6 pages manuscript submitted to a conference (ICCMA 2026)

This paper presents a mixed discrete-continuous multiobjective bilevel framework for the structure-actuation co-design of all-electric heavy-duty robotic manipulators. The upper level optimizes manipulator geometry and actuation topology, while joint-specific lower-level searches construct feasible archives of discrete motor, gearbox, and screw configurations. A system-level coordinator selects actuator packages according to hardware mass, co-design cost, and loss-aware supply energy, and the resulting actuator masses are fed back to the robot model until a mass-consistent fixed point is obtained. Evaluation on a full-pose SE(3) benchmark with a 100-kg tool payload yields eight feasible nondominated designs, all satisfying the 12 prescribed poses. Actuator-mass coupling converges in three iterations for every reported design. A fixed-design ablation shows that one-pass sequential sizing changes hardware mass by up to 2.13%, co-design cost by 10.20%, and supply energy by 9.40% in magnitude. Payload screening further reveals increasing mass-cost-energy demand and changes in competitive mechanism topology with carried load.

0.45

Attribution-Gated Joint Estimation of Intention and Capability for Assist-as-Needed Upper-Limb Robots

cs.RO ·2026-10-15 ·Pengcheng Li, Shuxiang Guo, Hanze Wang, Jun Leng, Bin Wang +1 more
similarity 0.52
Abstract · 31 pages, 7 figures

Assist-as-needed (AAN) control must distinguish between changes in intended motion and changes in effective voluntary torque capability, even though both can produce similar kinematic and interaction responses. A dual-measurand multimodal MHE-MPC architecture is developed as the base framework, in which the intended trajectory and the task-dependent effective voluntary torque capability are estimated online as distinct quantities, and both estimates are used to adapt robotic assistance. Building on this architecture, the ambiguity between the two update channels is formulated as a continuous credit-assignment problem and resolved by an attribution gate. A trajectory-change indicator is obtained from persistent corrective interaction, whereas a capability-change indicator is derived from the residual between normalized muscle activation and dynamics-reconstructed voluntary torque. Nine healthy participants completed factorial target-height-load trials and a pre-post fatigue cup-transport task. Without target-height input, the gated method generated correctly ordered Low-Middle-High references under every load: target changes were preferentially assigned to trajectory adaptation, whereas added load shifted adaptation toward the capability channel. It achieved the lowest RMSE in all nine conditions (0.017 rad versus 0.041 rad for ungated dual estimation and 0.127 rad for fixed-reference error-based AAN). Post-fatigue capability estimates decreased and assistance increased at all heights, supporting functional feasibility.

0.20

FORTE: Task-Adaptive Force Capability Optimization for Mobile Manipulators

cs.RO ·2026-09-18 ·Xiao Wang, Heng Zhang, Gokhan Solak, Fei Zhao, Arash Ajoudani
code/data similarity 0.52
Abstract

Effective physical interaction control in robotic manipulation requires not only kinematically feasible motion but also sufficient force-interaction capability. Existing redundancy resolution methods often ignore task-specific force demands or maximize the force capability indiscriminately, sacrificing dexterity when large force margins are unnecessary. We propose a task-oriented force capability optimization framework for redundant mobile manipulators. A Vision-Language Model (VLM) infers object physical properties from an RGB image and a task description, generating a desired task-force sequence that captures gravitational and inertial demands. We then define a task-oriented force capability metric as the signed distance between a task-force uncertainty ball and the dynamic residual force polytope (RFP), quantifying compatibility between task demands and the robot's remaining actuation capacity. This metric is incorporated, alongside manipulability, joint-limit avoidance, trajectory smoothness, and base-oscillation suppression, into a whole-body multi-objective trajectory-optimization problem. Experiments on a mobile manipulator performing lifting and single-point-holding tasks under varying payload conditions demonstrate that the proposed method provides sufficient force capability for heavy loads while preserving high manipulability for light loads. This yields a task-adaptive balance that fixed capability-maximizing baselines (RFP inscribed radius, RFP cone) and manipulability-only optimization fail to achieve. The core implementation is publicly available at https://github.com/yeying256/FORTE.

0.42

Residual Wrench Certification and Margin-Aware Control Synthesis for Aerial Physical Interaction

cs.RO eess.SY ·2026-09-30 ·Abhimanyu Khadga, Abhinav Sinha, Shashi Ranjan Kumar
similarity 0.52
Abstract

We develop a task-relative framework for certifying residual wrench authority after hover and contact loading in multirotors with bounded actuators. Using convex geometry, we derive signed margins for prescribed convex reserves, including Euclidean balls and weighted ellipsoids. We obtain computable reserve certificates from actuator-interiority bounds to support slack-maximizing allocation. To preserve the required reserve, we propose command projection onto a tightened feasible set. We then connect the available reserve to structured gain synthesis and certify a local tracking region that respects actuator limits. Within this region, we establish nominal exponential convergence and robust ultimate boundedness. For the prescribed task and morphology family, we show that the optimized octarotor attains a larger margin than the optimized hexarotor at equal total thrust. We evaluate the proposed framework in closed-loop simulations of sustained rigid-wall contact using a fixed-geometry octarotor and a variable-tilt quadrotor with matched installed thrust. The quadrotor's local certificate admits a higher normalized push limit for the prescribed task family. In tests beyond the realizability boundaries, we observe the predicted loss of authority through rotor-thrust limits for the octarotor and tilt-servo limits for the quadrotor.

0.17

Systematic Lightweight Method for Robotics Based on Strain Energy Distribution Optimization

cs.RO ·2026-08-29 ·Jingchen Li
similarity 0.51
Abstract

Service robots work with people and are highly expected to be lightweight for safety, agility and energy conservation. As a complex mechanical system, a robot consists of a large number of components and has various working configurations and load environments. An effective method for achieving system-level optimal robot design is a crucial requirement, but it poses significant challenges. In this study, we introduce a novel approach to optimize the distribution of strain energy, which can significantly improve the effectiveness of systematic optimization in a complex system. First, we present and demonstrate that the strain energy per unit mass should be uniformly distributed in an optimal lightweight mechanical system. Based on this criterion, the system-level problem can be decoupled and the design objective of each part can be assigned based on the strain energy. Then, each part can be optimally designed separately according to its specific circumstances by using different approaches, such as size optimization, topological optimization, and material optimization. In this way, the optimization is at the system level, while the computational complexity is at the part level. Weight reduction and improvements in mechanical properties can be obtained simultaneously. As an example, this method is applied to an arbitrarily designed robotic arm, and its effectiveness is further demonstrated in the cases of lightweight with stiffness improvement, considering multiple materials, multiple working conditions, and vibration performance.

0.43