CS Paper Radar

Reliability Assessment of FRP-RC Columns Using AK-MCS with a Piecewise Two-Branch Approach

Arndt Goldack, Richard Koehler, Ahmed Usama Syed

cs.CE stat.APstat.CO ·submitted 2026-10-25 17:49 UTC · v1

Abstract

Slender concrete columns reinforced with fiber-reinforced polymer (FRP) bars fail at medium to high axial load levels either by concrete crushing or by loss of stability, while the tensile strains in the reinforcement remain far below the rupture strain. Each non-linear finite element (FE) analysis yields only the capacity of the governing failure mode, and the governing mode changes over a broad zone in which both capacities are nearly equal. Both characteristics conflict with active-learning Kriging-assisted Monte Carlo simulation (AK-MCS), which assumes a single, smooth limit-state function. This paper proposes a piecewise, two-branch AK-MCS framework in which each failure mode is represented by its own Kriging model, trained only on the FE analyses in which that mode governs, and the governing prediction is the minimum of both. Safeguards against data starvation keep rarely governing branches usable. After convergence, additional FE analyses are placed based on a leave-one-out calibration check and on the width of the confidence interval on the reliability index. A design-point search on the surrogate and importance sampling at the design points provide the reliability index even where direct Monte Carlo simulation finds no failure. For an FRP-reinforced concrete column example with mixed failure, 79% and 62% of the training points lie near the mode boundary. The reliability index from the design-point search agrees with the Monte Carlo estimate to within 0.05, and an FE analysis at the design point confirms the surrogate to within 0.6%.

Comment
22 pages, 5 figures

Closest papers

Nearest neighbours by meaning across the whole index.

A Physics-informed Neural Network Approach for Robust Buckling Load Prediction and Reliability-Based Design of Thin Truncated Conical Shells

cs.LG ·2026-08-22 ·Devasmit Dutta, Budhaditya De, Rohan Majumder, Sudip Kumar Mishra
similarity 0.57
Abstract

Thin-walled truncated conical shells are widely used in aerospace, marine, offshore, and lightweight infrastructure systems due to their high strength-to-weight ratio and geometric efficiency. Their buckling resistance under axial compression, however, is highly sensitive to geometric imperfections, manufacturing tolerances, material variability, and nonlinear instability effects. Conventional design procedures rely on conservative knockdown factors (KDFs), such as those recommended in NASA SP-8019, which do not explicitly account for shell geometry, fabrication quality, data uncertainty, or target reliability. This study develops a physics-informed neural network (PiNN) framework for predicting critical buckling loads of thin truncated conical shells and integrates the trained surrogate within a reliability-based design (RBD) formulation. The model combines geometric and material descriptors with mechanics-informed features derived from shell stability theory and the localized reduced stiffness method (LRSM). A physics-informed loss function penalizes mechanically inadmissible predictions exceeding the theoretical elastic buckling load. The framework is trained and evaluated using 133 experimental Mylar conical shell tests under axial compression. Compared with a conventional deep neural network (DNN), the PiNN improves predictive accuracy, reduces mean absolute error, and enhances physical consistency. The trained PiNN is then used to evaluate reliability indices and calibrate safety-consistent KDFs for prescribed target reliability levels. Results demonstrate that the PiNN-RBD framework provides an efficient approach for uncertainty-aware design of imperfection-sensitive shell structures.

0.49

Label-free physics-informed strength reduction and a neural operator for the reliability of spatially variable slopes

cs.CE ·2026-10-04 ·Apisit Robjanghvad, Sompote Youwai
similarity 0.50
Abstract

This paper proposes a label-free physics-informed neural network (PINN) for non-associated Mohr-Coulomb plasticity with incremental strength reduction for the reliability of spatially variable $c$-$φ$ slopes. The PINN is trained with a virtual-work loss on the finite-element mesh and solves many random fields at once on a graphics processing unit. With a solver budget fixed on the homogeneous slopes, it reproduces the Abaqus factor of safety within 2 to 3% root-mean-square on 52 random fields and locates the failure mechanism in the same weak zones, with the plastic strain in the band under-resolved. A neural operator trained only on the PINN solutions predicts the factor of safety, displacement path and failure mode of a million fields in seconds. No finite-element solution enters the pipeline: Monte Carlo fields, importance samples and operator training data come from the PINN, and Abaqus serves only to verify the result. Monte Carlo simulation, the first-order reliability method, importance sampling and the operator give consistent failure probabilities down to $10^{-3}$ for the slope studied, but a 3% scatter in the factor of safety inflates a probability of $10^{-3}$ by up to a factor of two, and the absolute values refer to one mesh. A heterogeneous Bishop analysis gives failure probabilities 2.6 and 8.3 times lower although its critical circles follow the PINN mechanism, because a small difference in the factor of safety is amplified in the tail. The operator also yields the failure mechanism and displacement response conditional on failure.

0.27

Finite Element Model Updating-based Load Rating of Bridges with Incomplete As-Built Information

cs.CE ·2026-08-31 ·Mehrdad S. Dizaji, Devin K. Harris, Mohamad Alipour, Abdou Ndong, Osman Ozbulut +1 more
unusual similarity 0.48
Abstract · 33, 18

Load rating is the engineering process of determining the safe load-carrying capacity of an existing bridge structure often through analysis of its load-bearing members and their cross sections. However, when structural drawings and details of the structure are missing or insufficient for such calculations, alternative solutions must be used to infer the capacity. This study proposes a rational and consistent engineering solution for capacity inference based on structural identification (St-Id). The proposed approach uses finite element model updating (FEMU) to estimate the unknown characteristics of structures for use in an analytical load rating, which requires the development of an initial model developed in ABAQUS that can be updated based on experimental test data. ABAQUS allowed for the development of an interface with MATLAB, which facilitated the integration of an automatic iterative parameter optimization algorithm. The optimization algorithm developed in this investigation incorporated the features of a genetic algorithm (GA) and a gradient-based scheme to iterate on the unknown parameters. The proposed approach was evaluated on four in-service highway bridges including two concrete slab and two T-beam structures in varying deterioration condition states, which had sufficient plans available but were treated as having varying degrees of unknown details. The results illustrated that the finite element (FE) model updating approach generated load ratings that were within 0-17% of the target load ratings while alleviating the main challenges of the existing alternatives.

0.27

Explainable Machine Learning Analysis of Temperature Effects on Mechanical Strength of Fiber-Reinforced High-Performance Concrete

cs.LG ·2026-10-16 ·Jagaran Chakma, Zhiguang Zhou, Badhan Chakma, Priyanta Chakma
unusual similarity 0.48
Abstract · 29 pages

Predicting the compressive strength of fiber-reinforced high-performance concrete subjected to temperature exposure is challenging because to the intricate interdependencies of mixture composition, fiber properties, curing conditions, and temperature. A data-driven framework to predict compressive strength utilizing 1,204 experimental records containing a diverse array of material designs and exposure situations. This study evaluates eight machine-learning models and demonstrate that ensemble approaches routinely surpass individual learners. Both gradient boosting and extreme gradient boosting exhibit superior performance on unseen data, each attaining a R^2 of 0.903. Gradient boosting produces the minimal root mean square error (6.67 MPa), whereas extreme gradient boosting achieves the lowest mean absolute error (3.97 MPa) and mean absolute percentage error (10.60%). The models are further interpreted utilizing Shapley additive explanations and partial dependence analysis, which reveal temperature as the primary factor influencing compressive strength, succeeded by fine aggregate, superplasticizer, cement content, water-to-binder ratio, and water content. Strength diminishes significantly with rising temperature, albeit the extent of deterioration is contingent upon the specific combination design. The best performing models are subsequently implemented in a Python-based graphical user interface for expedited prediction. Our findings offer a precise and comprehensible methodology for evaluating temperature-dependent compressive strength and facilitate the practical, data-driven design of fiber-reinforced high-performance concrete.

0.26

Life-cycle structural reliability of RC bridge piers under corrosion in a changing climate

cs.PF ·2026-11-16 ·Giuseppe Vittorio Nava, Luca Capacci, Fabio Biondini, Lorenzo Casti
publishedunusualhighly cited similarity 0.47
Abstract

Aging and deterioration processes of structures and infrastructure systems can be severely affected by the long-term evolution of environmental conditions expected in a changing climate. This paper aims at investigating the interaction between climate change and environmental aggressiveness on the probabilistic life-cycle performance of concrete structures under corrosion. A simulation-based framework is proposed for life-cycle structural reliability analysis under climate change scenarios. The framework is applied to a bridge pier with hollow core cross-section exposed to chloride-induced corrosion. The results allow to quantify the impact of climate change on long-term probabilistic structural response and highlight the need for proper modeling of the environmental parameters and climate evolution over the entire lifespan of aging structures for optimal life-cycle maintenance and management of structural and infrastructural facilities.

0.61

A Hybrid Gaussian Process-Extreme Gradient Boosting Machine Learning Framework for Robust Knockdown Factor Prediction and Reliability-Based Design of Thin Spherical Shell Caps

cs.LG ·2026-10-11 ·Budhaditya De, Rohan Majumder, Devasmit Dutta, Aman Deep Gupta, Sudib Kumar Mishra
theory similarity 0.47
Abstract

Elastic buckling remains a critical concern in the design of deep spherical shell caps, given that experiments reveal a significant reduction of critical loads from those predicted by linearized eigen-buckling analysis. This discrepancy has been attributed to initial geometric imperfections and is often reconciled through a dimensionless parameter, namely the knockdown factor (KDF). However, conventional KDFs (NASA SP-8007; Eurocode 3) are highly conservative, as they represent the lower bound of an extensive body of experimental data. This study aims to narrow the conservatism in the KDFs for spherical shell caps through machine learning (ML) regression models trained on experimental data on spherical shell buckling. A hybrid model is proposed by combining Gaussian Process Regression (GPR) with Extreme Gradient Boosting (XGBoost), and its improved performance is demonstrated over conventional ML algorithms, i.e., the Artificial Neural Network (ANN), Support Vector Regressor (SVR), Random Forest Regressor (RFR), and Histogram-based Gradient Boosting (HGBoost). Each of these models uses six input features and a single output, i.e., the KDF. The most critical feature affecting the KDF is ascertained through a sensitivity analysis. The study concludes with a reliability-based design framework that relies on the predictive ML model to obtain safety-consistent, yet less conservative, KDFs.

0.19

Assessment of Machine Learning-Based Critical Heat Flux Models in the CTF Subchannel Code for Square Rod Bundle Prediction

cs.LG ·2026-09-18 ·Aidan Furlong, Vinicius de Melo Monteiro, Robert Salko, Juliana Pacheco Duarte, Xu Wu
similarity 0.47
Abstract · 28 pages, 10 figures

The prediction of critical heat flux (CHF), a key safety-related quantity in nuclear thermal hydraulics, remains an important challenge due to its direct relationship with fuel performance and reactor safety. Recent studies have demonstrated that relative to traditional empirical correlations and lookup tables (LUTs), machine learning (ML) methods can substantially improve CHF prediction accuracy. Most ML-based CHF models, however, have been developed and evaluated using tube databases, leaving their applicability to reactor-relevant rod bundle geometries largely unexplored. This study evaluates ML-based CHF models deployed within the CTF subchannel code using the Electric Power Research Institute (EPRI) rod bundle CHF database. Both pure and hybrid residual correction models are considered in local and semilocal formulations. The tube-trained ML CHF models generally transferred favorably to rod bundle applications and outperformed traditional CHF methods across most geometries and operating conditions. The local hybrid LUT model produced the strongest overall performance, and the semilocal pure ML model remained highly competitive. Comparison against the Bowring correlation, W-3 correlation, and 2006 Groeneveld LUT demonstrated that substantial improvements in rod bundle CHF prediction are possible even when models are trained exclusively on tube data. These findings provide one of the first large-scale assessments of ML-based CHF models in square rod bundles within a production-level subchannel analysis environment and support their broader application in reactor thermal hydraulic analysis.

0.33

Fracture-Bench: A Controlled Benchmark Suite for Machine Learning Surrogates in Phase-Field Fracture Mechanics

cs.CE physics.comp-ph ·2026-11-02 ·Meenu Krishnan U., Maryam Hakimzadeh, Indrashish Saha, Meer Mehran Rashid, Lori Graham-Brady +1 more
benchmark similarity 0.45
Abstract · 38 pages, 15 Figues

Machine-learning surrogates are increasingly proposed to replace phase-field fracture simulations in many-query tasks such as uncertainty quantification, inverse analysis and design. Little controlled evidence shows which architectures are reliable, for which fracture problems and how far beyond their training data. We introduce Fracture-Bench, an open benchmark of two phase-field datasets with fixed splits, common test metrics and a description of each dataset's physical regime. Dataset~1 contains 1,000 AT2 simulations of multiple cracks growing from a notched hole in a hyperelastic plate under random non-uniform biaxial boundary displacements (44 load steps, $128\times128$ grid). Dataset~2 contains 4,000 PF-CZM simulations of a pre-cracked plate with two inclusions, each ten times stiffer or more compliant than the matrix ($128\times256$ grid). We train a Fourier neural operator (FNO), DeepONet, Latent DeepONet, a UNet and a conditional diffusion model on identical splits and compare one test metric per dataset, training time, inference time and model size. On Dataset~1, FNO and Latent DeepONet attain mean test errors of order $10^{-6}$, about ten times lower than UNet and DeepONet. On Dataset~2, the diffusion model is most accurate, with about one sixth of the UNet error, but requires \SI{706}{s} per prediction versus \SI{6}{ms} for UNet. For all architectures, most of the error occurs in the final load steps, after crack localization. Dataset~2 contains initial cracks less than one grid cell apart that produce qualitatively different paths. Architecture rankings therefore depend on the task, and errors averaged over densely sampled inputs reveal little about near-bifurcation cases. Data, codes, splits, regime descriptors and generalization splits are public, with a protocol for adding under-represented regimes such as mixed-mode, three-dimensional and experimentally paired fracture.

0.21