CS Paper Radar

Hybrid Residual Reinforcement Learning for Contact-Rich Robotic Book Insertion

Tianyuan Liu, Rutherford Agbeshi Patamia, Benjamin Champion, Akansel Cosgun, Richard Dazeley

cs.RO ·submitted 2026-09-17 09:34 UTC · v1

Abstract

Placing a grasped book into a tight shelf is a compact but difficult contact-rich control problem: millimetre-scale pose error can turn a geometrically valid approach into jamming, failed release, or incomplete seating. We study this final phase after grasp acquisition and global approach, and ask how control authority should be divided between known geometry and learned behaviour. Our method retains a nominal task-space controller for structured insertion and seating, while residual PPO supplies bounded local corrections and decides when to release. Only the brief open-retreat-reclose transition is scripted. For the final policy used on hardware, a deployment-matched simulation evaluation over 512 fixed conditions yields 98.50 percent mean success (0.23 percentage-point sample SD) across three independent training runs, compared with 37.89 percent for nominal control. On the physical xArm7, 60 trials over 30 matched conditions show the same qualitative advantage: residual control raises success from 26.7 percent to 63.3 percent, reduces failures from 22 to 11, and wins 13 of the 15 matched conditions in which the two controllers differ. Robustness tests show that performance remains above 87 percent under initialization perturbations up to 1.5x, while very tight clearances expose the geometric limit of local correction. These results support a hybrid design in which geometry preserves reliable task structure and learning is concentrated on the contact-sensitive behaviour that fixed rules handle poorly.

Comment
8 pages, 8figures

Closest papers

Nearest neighbours by meaning across the whole index.

Learning Reflexive Behavior for Contact-Rich Manipulation

cs.RO ·2026-10-02 ·Quan Nguyen, Yunho Kim, Joonho Lee
similarity 0.73
Abstract

During contact-rich manipulation, interactions between a robot and its environment carry information about local geometry: a surface prevents penetration, a bore guides a peg. A controller that exploits these interactions can comply with environmental constraints while preserving task intent. Robot-earning systems commonly use position, hybrid force-position, or Cartesian impedance control. Their prescribed tracking objectives, stiffness, or force-control directions may not match local constraints and may degrade performance. We learn a proprioceptive reflex policy in simulation on three simple interaction primitives: a spring, a plane, and a rail. The policy maps task-space commands to joint-position targets using state history, without direct force or geometrical measurements. Once trained, it serves as a frozen execution layer beneath higher-level controllers. We evaluate it in dual-arm box lifting, peg insertion, and surface following. In box lifting, the reflex kept the force below the threshold while the baseline failed. In rough-surface following it stayed below the 10 N reference, on par with tuned hybrid force-position control. In 0.02 mm peg insertion It reduced mean estimated contact force to less than half that of the baseline while increasing hardware success rates from at most 22 % to 36-58 %. By separating contact response from command generation, the reflex policy provides motion planners, learned policies, and teleoperators with robust contact-rich execution.

0.15

InsertAnything: Generalizable Contact-Rich Precision Insertion from Simulation to Reality

cs.RO ·2026-09-21 ·Zhenghua Ma, Xinpan Meng, Zeyu Liu, Muyuan Ma, Hengdi Zhang +2 more
benchmarkcode/data similarity 0.73
Abstract

Contact-rich precision insertion is a key manipulation skill in robotic assembly. Tight clearances make insertion more sensitive to alignment errors and prone to collisions and jamming, while variations in geometry and clearance across parts further complicate policy reuse. We present a reinforcement learning framework that trains insertion policies entirely in simulation for direct deployment without real-world demonstrations or policy fine-tuning. By combining target poses with compact three-dimensional fingertip force feedback, the policy learns to search for alignment and correct its motion despite errors in the estimated hole position. A decoupled gated reward coordinates alignment and insertion. Force-signal smoothing and state-independent standard deviations stabilize the learning process. The resulting policies perform real-world insertion across multiple hole geometries with a minimum nominal clearance of 0.02 mm and improve success while reducing peak contact forces under hole-position errors. Cross-clearance and cross-geometry evaluations further confirm policy generalization. The system achieved the first perfect score of 20/20 on ManipulationNet's peg-in-hole benchmark under its Human-in-the-Loop protocol, with fully autonomous insertion motions. A single policy trained only on a simulated hexagonal insertion task achieved an overall success rate of 95.0% across eight unseen real-world insertion tasks. These results show that learning entirely in simulation can yield precision insertion skills that can be deployed directly and reused across real-world tasks. The project website (https://mzhsoul.github.io/InsertAnything/) provides open-source simulation and real-robot experiment scripts, assets, and trained checkpoints.

0.35

DynaForge: Planning-Guided Residual Learning for Dynamic Manipulation Demonstration Generation

cs.RO ·2026-09-22 ·Yiyang Jin, Yu Zheng, Xiao He, Hesheng Wang
similarity 0.71
Abstract · 8 pages, 6 figures. Under review

Dynamic object manipulation is essential for robots operating in real-world environments, yet methods for generating high-quality demonstrations remain limited. Methods designed for static tasks do not readily transfer to dynamic settings. Among dynamic demonstration generators, planning-based methods can fail near contact, while DOMINO-style replay simplifies dynamic interactions and may limit the experience available for policy learning. We present DynaForge, a planning-guided framework that learns residual corrections for dynamic manipulation demonstration generation. DynaForge combines low-frequency global planning with high-frequency object-centric inverse kinematics across task phases, and applies a residual policy to correct actions during dynamic interaction. An implicit curriculum groups rollouts under matched conditions and selects mixed-success groups, focusing residual reinforcement learning on the evolving competence frontier. On Can and Bottle, it uses 0.73x as many optimizer steps as vanilla GRPO at the same nominal environment-step budget, with higher observed final success rates. Across nine simulation tasks, DynaForge increases mean demonstration-generation success from 41.30% of the planning prior to 78.37%. With 800 demonstrations per task, DP3 policies trained on DynaForge data achieve 49.11% mean success, compared with 7.07% for DOMINO data. On three real-world dynamic tasks, DynaForge-trained policies achieve 30-60% success, compared with 0-10% for DOMINO-trained policies, showing the ability of DynaForge for sim-to-real transfer.

0.24

Learning to Leverage Compliance: A Policy-Admittance Learning Framework for Robotic Insertion

cs.RO ·2026-09-25 ·Chongren Wang, Minghe Li, Honghua Dai, Zhicheng Lin, Shiyang Wei +1 more
similarity 0.70
Abstract

Policy learning and compliant control offer a promising route to reliable autonomous assembly under pose errors and contact uncertainty. However, combining them does not ensure coordination: the policy may continue pushing against contact while the controller yields, producing sustained loading with limited progress. To address this problem, we propose LeCo (Leverage Compliance), a policy-admittance learning framework that guides a visual policy through execution-time interaction under fixed admittance. A multirate feedback mechanism aggregates high-rate contact-interaction records into policy-transition rewards. An integrated conflict cost then characterizes sustained policy-loading/controller-unloading opposition, while a directional high-force tail cost captures continued-loading events within a transition. Together with task completion, these costs encourage the policy to leverage compliance with less unproductive loading. We evaluate LeCo on four real connector-assembly tasks, obtaining an aggregate success rate of 94%. Across tasks, mean successful-trial resultant-force and torque peaks decrease by approximately 30% and 64% relative to the comparison baseline. Reward ablation further shows that adding conflict shaping reduces median successful-trial contact-conditioned conflict density by approximately 53%. These results support learning to leverage fixed compliance by turning multirate policy-admittance interaction into complementary reward signals for effective, lower-load insertion.

0.23

Constraint-Grounded Reinforcement Learning for Variable Impedance Control in Contact-Rich Robotic Insertion

cs.RO ·2026-09-11 ·Lin He, Min Deng
similarity 0.70
Abstract · 16 pages, 7 figures

In robotic insertion under uncertain contact, the axial force limit and the appropriate controller gain vary across tasks. As a result, a single fixed gain is unlikely to remain suitable across different task conditions, making conventional impedance controllers reliant on manual retuning. To eliminate manual retuning, we propose Constraint-Grounded Reinforcement Learning (CG-RL), a variable impedance framework for online gain adaptation. Conditioned on the force limit and contact feedback, the policy outputs a residual motion, an insertion rate, and a requested gain. The controller projects this gain into the admissible range without exposing the range itself to the policy. This separation allows a single policy to operate under different force limits without retraining or manual retuning. We evaluate CG-RL on simulated oblique insertion across five training seeds. CG-RL achieves an $85.8\pm7.7\%$ (mean $\pm$ SD) success rate of insertions without violating the force limit, while keeping the applied gain within the admissible range. As a comparison, a fixed-gain baseline using the midpoint gain achieves a success rate of $50.1\%$. The policy adapts its insertion rate continuously to the specified force limit and further generalizes to more permissive force limits above the training range. In contrast, the same actor without force-limit input does not exhibit this adaptation. The applied gain is guaranteed to remain within the admissible range, while force-limit satisfaction is validated empirically rather than guaranteed formally.

0.52

Dexterous Robot Manipulation from Human Demonstrations via Contact-Anchored Retargeting and Residual Policy Learning

cs.RO ·2026-09-21 ·Zihao Yang, Chengyuan Liu, Yu Zhou, Runze Lv, Tianyu Cui +4 more
code/datahighly cited similarity 0.70
Abstract · 16 pages, 6 figures, 5 tables. Technical report. Code: https://github.com/DexGEM-Lab/real2sim2real

Learning dexterous manipulation from demonstrations is bottlenecked by data: the contact forces that determine whether a grasp succeeds are absent from every scalable source of human demonstrations. This paper builds on two observations. First, what survives the change from a human hand to a robot hand is the contact structure of a demonstration - which finger regions touch which object locations, and in what order - rather than its joint motion. Second, physical consistency need not be engineered per task: a single residual reinforcement learning (RL) policy, trained once across diverse demonstrations, can repair kinematic recordings into physically consistent, contact-annotated trajectories, and the same residual formulation restores dynamic feasibility after retargeting. These observations yield a three-stage pipeline that converts human motion-capture recordings into dexterous robot policies with no real-robot training data: physics refinement with a simulated MANO hand recovers contacts and forces, contact-anchored retargeting transfers the demonstrated contact structure through an objective independent of hand morphology, and residual policy learning adapts the result to robot actuation. The pipeline reconstructs 25,454 single-hand trajectories (success 7.3% -> 59.3%) and 25 dual-hand tasks (16.0% -> 62.4%) with one shared policy per setting, transfers one human dataset to four morphologically distinct robot hands (+62.4 pp), and executes four contact-rich bimanual tasks on physical hardware with zero real-robot training data.

0.60

CALM: Current Aligned Link Manipulation for Single Arm Oversized Object Lifting

cs.RO ·2026-09-24 ·Jun Hu, Sihan Chen, Kosta Jovanovic, David Navarro-Alarcon, Xueqian Wang +2 more
similarity 0.70
Abstract

Most robots manipulate objects solely with their end effectors, whereas humans flexibly leverage different body parts, such as the forearm and elbow, especially when handling oversized objects. Learning such whole-arm manipulation is chal-lenging due to long-horizon sparse rewards, limited contact sens-ing, and the sim-to-real gap in contact and actuator dynamics. To address these challenges, we propose Current-Aligned Link Manipulation, a framework for learning long-horizon contact-rich manipulation using motor current as joint load related feedback. Three stage-specific policies first learn repositioning, grasping, and lifting using privileged simulation information, and a stage router sequences them to generate complete task demonstrations. For sim-to-real transfer, a causal current mapper predicts physical motor current from simulated joint histories, aligning the actuator current observation between simulation and hardware. A unified student policy then learns from these demonstrations using only deployable sensor observations and is further refined with DAgger. The task policies are trained entirely in simulation, and the final student is deployed on hardware. Experiments demonstrate 76.2% (762/1000 trials) complete-task success in simulation and 73.3% success (22/30 trials) on the physical robot for sequential oversized-object lifting.

0.23

Real-World Reinforcement Learning with MPC Scaffolding for Dexterous Manipulation

cs.RO ·2026-09-14 ·Emek Barış Küçüktabak, Karankumar Patel, Zhaodong Yang, Jinda Cui, Kazuhiro Sasabuchi +1 more
highly cited similarity 0.69
Abstract

Real-world reinforcement learning (RL) offers a promising route to dexterous manipulation policies that can adapt directly from physical interaction, but learning is hindered by inefficient early exploration and costly failures. We propose a framework that uses sampling-based model predictive control (MPC) as scaffolding for real-world dexterous RL, providing structured prior experience and task-directed guidance during learning without human demonstrations or corrective actions. A small set of MPC trajectories is first used to populate an offline replay buffer and to pretrain the actor and critic. During online learning, MPC intermittently guides data collection while an off-policy Soft Actor-Critic learner trains from both prior MPC experience and newly collected physical interaction, with control gradually transitioning to the learned policy. On continuous in-hand rotation with a 16-DoF Allegro hand, initialized from 20 MPC trajectories collected in 12 minutes on hardware, the policy reaches 100\% success after 7 minutes of online RL, with about three object drops on average during training. After 20 minutes of online learning, the policy achieves more than five times the rotation speed of the MPC controller and completes 1000 consecutive rotations without a drop. Ablations show complementary benefits from MPC-based pretraining, retained MPC experience, and online MPC guidance, while additional experiments demonstrate rapid adaptation to new object geometries and successful goal-conditioned reorientation.

0.44