CS Paper Radar

Walking on the Slope: Stable Bipedal Gaits with Genetic-Algorithm-Optimized Trajectories

Madhav Rijal

cs.RO ·submitted 2026-09-17 15:30 UTC · v1

Abstract

This paper presents the kinematic and dynamic modeling, trajectory generation, and stability analysis of an 8-degree-of-freedom (DOF) biped robot walking on flat and inclined terrain. Denavit-Hartenberg (DH) parameters and homogeneous transformations are used to derive the forward kinematics, while closed-form inverse kinematics maps the desired hip and swing-foot Cartesian trajectories, generated with cubic splines, to joint angles. Joint torques are computed using the Newton-Euler iterative algorithm, and dynamic stability is evaluated using the zero moment point (ZMP) criterion. A genetic algorithm (GA) optimizes the hip height, maximum swing-foot lift, and frontal-plane tilt angle by minimizing the work done by the joints subject to a ZMP feasibility penalty. Simulation results in MATLAB show that the nominal 8-DOF model remains ZMP-stable for step completion times down to 0.5 s and for slope inclinations up to 22.5 degrees with the given foot geometry. Beyond these limits, the ZMP leaves the support polygon, and either the foot dimensions or the trajectory parameters must be modified. The results also show that ZMP stability is governed by the mass distribution among the links rather than the total mass of the robot.

Closest papers

Nearest neighbours by meaning across the whole index.

Low-speed Limit Cycle Walking of Planar X-shaped Bipedal Robot with Special Properties

cs.RO ·2026-11-17 ·Fumihiko Asano, Cong Yan
published similarity 0.70
Abstract · 6 pages, 7 figures. Published in the Proceedings of IEEE ICARM 2023. This author version corrects bibliographic information and minor typogr…

This paper proposes a novel planar semicircular-footed X-shaped bipedal robot in which the center of mass of each leg link is at the same position as the hip joint, and discusses a method for generating a stable limit cycle gait on level ground. First, we outline the assumptions of the robot model with four degrees of freedom, and develop the mathematical equations of motion and collision. Second, we set the relative hip-joint angle as a control output and design a control system to follow it to the desired trajectory specified as a fifth-order function of time. Third, we mathematically show that there are special properties: the angular velocity of the swing leg does not change before and after the collision, and the time-integral of the control input becomes zero in a steady gait. We also mathematically show that the model has the feature that approximate linearization is effective and the antigravity effect of semicircular feet can be utilized. Through numerical simulations, we verify the validity of the theoretical results, and analyze some fundamental gait properties such as convergence speed and mechanical energy restoration.

0.36

Stability Principle Inherent in Wheel Gait of Planar X-shaped Walker Generated Using Constant Torque Drive and Mechanical Stoppers

cs.RO ·2026-11-16 ·Fumihiko Asano, Cong Yan
top venue similarity 0.65
Abstract · 8 pages, 6 figures. Published in the Proceedings of IEEE ICRA 2026. This author version corrects the author names in one reference; the scie…

Since the late 19th century when the first walking toys were developed, it has been known that mechanical stoppers at the hip joint are crucial for generating stable passive dynamic walking. Recent research on passive-dynamic and limit-cycle walkers has also confirmed that mechanical stoppers at the hip and knee joints are effective for generating stable walking motion, but theoretical research on how this mechanical constraint enhances the overall gait stability remains insufficient. This paper introduces a planar X-shaped walker equipped with mechanical stoppers at the hip joint, and investigates the effect of the mechanical constraint on the stability of the wheel gait generated by constant torque drive on a downslope. By simply falling forward while using the stoppers to constrain itself to the target impact posture, the robot can generate a highly stable wheel gait. We divide the motion of one step into four phases, derive approximate analytical solutions for the state error transition function matrix in each phase using a linearized model, and analyze the increase or decrease in the state error norm using metrics such as its maximum singular value. Numerical simulations demonstrate that while two phases are unstable in terms of the increase in the state error norm, the remaining two phases are stable, resulting in overall asymptotic stability.

0.51

Geometry-Aware Predictive Control for Walk-to-Run Bipedal Obstacle Crossing

cs.RO ·2026-10-11 ·Aashish Sahu, R. Prasanth Kumar
similarity 0.65
Abstract

This paper presents a geometry-aware predictive control framework for bipedal obstacle crossing across walking and running regimes. The proposed approach integrates a phase-structured trajectory generator with a constrained model predictive control (MPC) tracking layer to generate coordinated pelvis and swing-foot motions during obstacle traversal. The crossing process is represented through five interpretable phases: pre-crossing, leading-leg clearance, straddle, trailing-leg clearance, and recovery. Within this structure, swing-foot elevation is adapted as a function of obstacle height, while lateral stance widening and pelvis repositioning are introduced as functions of obstacle depth to improve transverse clearance and body alignment. A continuous gait-parameter evolution enables smooth walk-to-run transition without discrete controller switching. The generated references are tracked using MPC to regulate motion smoothness, clearance feasibility, touchdown behavior, and lateral admissibility. The framework is evaluated in reduced-order simulation over five progressively difficult obstacles under walking and running conditions. The robot successfully crosses the first four obstacles, achieving minimum body-obstacle clearances of 0.036, 0.036, 0.059, and 0.017 m, respectively. The fifth and most demanding obstacle leads to collision, identifying the current operating boundary of the proposed reduced-order formulation. Overall, the method provides a compact, interpretable, and computationally efficient basis for intelligent obstacle-aware bipedal locomotion.

0.24

Hip Energized Monopedal Hopping

cs.RO ·2026-08-11 ·Shane Rozen-Levy, Griffon McMahon, Daniel Koditschek
similarity 0.63
Abstract · 35 pages, 11 figures

We present a novel stepping strategy for pitch unlocked planar monopeds where the reaction torques from stabilizing pitch with a conventional PD + feedfoward controller are recruited to counteract energetic losses from damping. By moving the location of the mass center, our controller increases the pitch stabilization torque, thereby adding energy to the gait. A new stepping policy adjusts the distribution of energy between the radial and angular degrees of freedom to counteract dissipative losses and achieve a user specified balance between steady state fore-aft speed and apex height. Hybrid averaging analysis yields closed form expressions for the fixed points and eigenvalues of the resulting gait, lending insight into the interplay between the physical and control parameters' influence on performance. Simulation studies on a generic 5 link biped and a careful model of the Penn Jerboa reveal a useful correspondence to these analytical predictions. Physical experiments on the Penn Jerboa exhibit stable locomotion with speeds ranging from 1.02 m/s to 1.77 m/s (5.10 leg lengths/s to 8.85 leg lengths/s) in a manner effectively approximated by the mathematical analysis.

0.10

When to Waddle: A Comparative Study of Bipedal Torso-Stabilization on Low-Friction Surfaces

cs.RO ·2026-09-18 ·Ben Gu, Naomi Oke, George Ortiz, Stacy Ashlyn, Cordelia Pride +2 more
similarity 0.61
Abstract

Low-friction surfaces challenge bipedal locomotion by limiting the contact forces available during stepping. Inspired by penguin waddling, we investigate how lateral torso motion and center of mass (COM) placement affect locomotion as surface friction changes. Using a five-actuator biped, we compare an upright-gait strategy with a penguin-inspired torso-over-stance-leg strategy across multiple COM placements in simulation and hardware. In the 3-D simulator MuJoCo, we sweep through sinusoidal leg and hip actuation parameters across four friction coefficients mu = 0.1, 0.3, 0.5, 0.7. In simulation, torso-over-stance-leg motion produces more successful controllers and higher forward speeds at low friction, with the highest speed occurring for the high-COM configuration. Hardware experiments show the same low-friction speed trend: at mu=0.12, torso-over-stance-leg motion increases forward speed and reduces cost of transport at both tested COM ratios, and the higher COM also improves both measures. The high-COM penguin configuration is the fastest and most energy efficient while maintaining low sideways foot motion. At mu=0.45, the COM trend reverses: the lower-COM configurations are faster and more energy efficient, while gait strategy has little effect on forward speed but still changes sideways foot motion. These results show that the effects of lateral torso motion and COM placement depend on the available friction, and that forward speed, energy use, and slip-related foot motion can be modulated with a penguin-inspired torso motion on hardware.

0.22

Central pivot point control of a body-attached spring-mass runner: periodic gaits, stabilization, template embedding and approximate analytic return maps

cs.RO eess.SYmath.DSphysics.bio-ph ·2026-11-02 ·İzel Sever, O. Kaan Karagöz, M. Mert Ankaralı
similarity 0.61
Abstract · 21 pages, 15 figures. Submitted to Chaos: An Interdisciplinary Journal of Nonlinear Science

The spring-loaded inverted pendulum (SLIP) describes the center-of-mass (COM) motion of runners but has no trunk. In trunk models, the hip torque couples posture and COM motion and destroys the central-force structure on which SLIP analysis relies. As a result, trunk models have been studied almost only numerically. We show that this structure can be restored. The central pivot point (CPP), a hip-torque law that directs the ground reaction force through the COM, decouples pitch exactly and reduces stance to a planar central-force problem. At upright posture, time-reversal symmetry produces one-parameter families of periodic gaits. A stance-phase pitch law and a stride-level regulator stabilize all computed gaits, also with bounded hip torque and friction. Under CPP, any radial force law in virtual-leg coordinates can be embedded independently of posture. For a linear radial template, the stance radius and the constant-momentum sweep have exact closed forms. With a new gravity correction, the resulting analytic return map, to our knowledge the first for a trunk model, predicts liftoff velocity and apex position with mean errors of 1.6% and 0.9%. The natural gaits of the embedded runner are symmetric and need no force step at touchdown. A near-reversibility argument explains their unit multiplier, and a scalar equation predicts them within 0.8%. A deadbeat stride controller based on the analytic map tracks changes of speed, height and posture. CPP thus makes trunk models accessible to the analytic tools developed for SLIP.

0.29

Modeling and Control of a Rigid-soft Hybrid-link Humanoid Robot

cs.RO ·2026-10-10 ·Zewen He, Taiki Ishigaki, Ko Yamamoto
published similarity 0.60
Abstract

Physical flexibility plays a significant role not only in human motions but also in robot motions. For example, a humanoid robot with passive and flexible elements, which can be regarded as a rigid--soft hybrid-link system, has the advantages of storing energy and mitigating impact in a dynamic motion. However, the motion design and control of a hybrid-link system are challenging to achieve and have only been discussed in the literature. In this study, we propose the framework of inverse kinematics and compliance optimization-based control for a hybrid-link humanoid system that represents the continuous deformation of a flexible structure using the piece-wise constant strain (PCS) model. The proposed method was validated using forward dynamics simulations for standing, jumping, and walking motions. Then, we built an experimental setup using a biped humanoid robot with leaf-spring type prosthesis leg, in which the prosthesis deformation was measured by a motion capture system. Using this setup, we experimentally validated the proposed method for standing balance control in both double- and single-support cases.

0.45

Passive-Dynamic-Walking-Inspired Dynamics Guidance for Energy-Efficient Humanoid Locomotion

cs.RO ·2026-09-28 ·Hyeonjin Choi, Joongheon Kim, Daekyum Kim
similarity 0.58
Abstract

Learning energy-efficient humanoid locomotion requires discovering mechanically economical gait coordination, not merely reducing actuator effort. Reinforcement learning promotes efficiency through effort-related reward penalties, which guide the step-to-step mechanics of walking only indirectly. This article proposes a framework inspired by passive dynamic walking (PDW) that temporarily creates slope-equivalent conditions favorable to economical gait discovery and removes all PDW-specific guidance before nominal-dynamics optimization. During early training, a tilted-gravity field assists sagittal progression on flat collision geometry, complemented by curriculum-coupled reward terms. The core framework requires no reference trajectories, gait phases, or contact schedules. In a five-seed forward-locomotion study on a 29-DoF Unitree G1, the framework reduces mechanical cost of transport by 6.8-15.2% over commanded speeds of 0.5-2.0m/s without degrading velocity tracking. Mechanical-work decomposition attributes the reduction to positive actuator work, and reward-matched comparisons separate the guided regime's faster gait acquisition from the tilt's additional benefit to converged economy. The framework extends to unassisted omnidirectional locomotion, where its benefit persists once a walking-specific motion prior supplies kinematic coordination, the combination reducing speed-matched cost of transport by 18.7%. On hardware, forward cost of transport falls by 16.3% with the motion prior and by 4.5% without it, the latter within the trial-to-trial spread.

0.22