CS Paper Radar

Modeling and Control of a Rigid-soft Hybrid-link Humanoid Robot

Zewen He, Taiki Ishigaki, Ko Yamamoto

cs.RO ·submitted 2026-10-10 17:13 UTC · v1
published

Abstract

Physical flexibility plays a significant role not only in human motions but also in robot motions. For example, a humanoid robot with passive and flexible elements, which can be regarded as a rigid--soft hybrid-link system, has the advantages of storing energy and mitigating impact in a dynamic motion. However, the motion design and control of a hybrid-link system are challenging to achieve and have only been discussed in the literature. In this study, we propose the framework of inverse kinematics and compliance optimization-based control for a hybrid-link humanoid system that represents the continuous deformation of a flexible structure using the piece-wise constant strain (PCS) model. The proposed method was validated using forward dynamics simulations for standing, jumping, and walking motions. Then, we built an experimental setup using a biped humanoid robot with leaf-spring type prosthesis leg, in which the prosthesis deformation was measured by a motion capture system. Using this setup, we experimentally validated the proposed method for standing balance control in both double- and single-support cases.

Closest papers

Nearest neighbours by meaning across the whole index.

Online iLQR-MPC with Whole-Body Control for Robust Humanoid Locomotion

cs.RO ·2026-11-03 ·Xiang Li, Linlin Ou, Ruihan Wu, Xinyi Yu
similarity 0.65
Abstract

Humanoid locomotion requires deciding where to step and how to distribute contact forces. However, a disturbance can invalidate the nominal plan, requiring coordinated revision under constraints that switch with every footfall. To solve this online, the proposed approach employs the single-rigid-body model, which retains attitude dynamics and the full contact wrench. An iterative linear-quadratic-regulator MPC (iLQR-MPC) then jointly optimizes contact forces and footstep locations in a single receding-horizon problem, without a separate step planner. Specifically, contact and motion constraints are incorporated into the backward pass through augmented-Lagrangian and relaxed-barrier penalties. A whole-body controller subsequently maps the plan to joint torques at 500 Hz while preserving contact feasibility. The model-based formulation makes disturbance responses interpretable through explicit costs and constraints, and requires no platform-specific policy training. In MuJoCo simulations, the iLQR-MPC replans at 100 Hz (mean solve time 8.9 ms); the Unitree G1 sustains steady-state walking and recovers from impulsive 245 N forward and 175 N lateral pushes.

0.18

Design and Analysis of a Nonlinear Parallel Mechanism Coupling for Dynamic Humanoid Legs

cs.RO ·2026-10-12 ·Rohit Kumar, Heiner Peters, Felix Wiebe, Franek Stark, Janne Janzen +3 more
similarity 0.64
Abstract

Humanoids increasingly demand lightweight leg mechanisms for agile, dynamic, and energy-efficient locomotion. Reducing distal inertia through proximal actuation has thus become a common design goal. Yet, compact transmissions that preserve torque capability and efficient force transmission remain hard to achieve. This paper presents a novel series-parallel leg design combining a knee parallel mechanism, an ankle parallel mechanism, and a nonlinear knee-ankle coupling where all actuators placed closer to the hip. As the knee flexes, the coupling passively assists ankle dorsiflexion for foot clearance and, as it extends it assists plantarflexion for push-off, redistributing ankle load through the knee transmission. We derive the coupling's nonlinear transmission models and validate them in simulation and on hardware. The design shows that the shared transmission lets both joints draw on each other's actuator capacity by easing the knee's peak torque demand under load and the ankle's peak speed demand during fast motion. With the leg's proximal actuator placement, the leg achieves an effective reflected mass of 0.37 kg at the foot for a 6 kg leg, demonstrating very low distal leg inertia for dynamic humanoid robots.

0.12

A Dual-Cam Parallel Elastic Actuator with Shared Gas-Spring Compensation for Humanoid Ankles

cs.RO ·2026-08-31 ·Jingcheng Jiang, Yifang Zhang, Nikos G. Tsagarakis
published similarity 0.64
Abstract · Accepted to IEEE AIM 2026. Copyright 2026 IEEE. Personal use of this material is permitted

To improve torque capacity and energy efficiency of humanoid ankles, this paper proposes a 2-DoF parallel elastic actuator (PEA). The main novelty of the proposed design lies in its dual-cam, single-gas-spring architecture, which enables torque compensation in both pitch and roll using a shared elastic element, thereby improving structural compactness compared with conventional multi-element compensation schemes. By leveraging parallel gas springs and customized cam modules, the proposed architecture provides dual-axis torque assistance tailored to specific task requirements. The second key contribution is the formulation of a coupled 2-DoF mathematical model that explicitly captures the interdependence between the two compensation units through the shared spring. Based on this model, an optimization-based design framework is developed to synthesize customized cam profiles from prescribed torque references, establishing a systematic link from task requirements to hardware realization. The complete lower-leg CAD integration is presented in detail. Static FEA and kinematic simulations confirm the design's feasibility and torque-relief effectiveness. The results highlight the proposed design as a compact, customizable solution for 2-DoF humanoid ankle torque compensation.

0.48

Dataset-Free Compliant Humanoid Loco-Manipulation with Dynamic Online Posture

cs.RO ·2026-10-05 ·Seungho Yeom, Zhenyu Wu, Jaeyoung Huh, Diego Williams, Yuheng Zhi +2 more
similarity 0.63
Abstract

Most humanoid loco-manipulation controllers require human motion data to learn whole-body coordination and posture, leaving policies reliant on external sources to provide this data. We present OCLO (Online-posture Compliant LOco-manipulation), a humanoid loco-manipulation system trained without human motion data and commanded only through two end-effector targets. Because these targets do not uniquely determine whole-body posture, OCLO generates pelvis height and torso orientation online using an analytic reachability prior, further refined through policy-in-the-loop sampling with a task-agnostic cost. OCLO also learns whole-body compliance by displacing end-effector references according to measured forces through a spring-damper model, encouraging the legs, waist, and pelvis to yield to external loads. In simulation, using the reachability prior leads to a 77.8% success rate in acquiring the commanded reference, a vast improvement over the 37.8% success rate accomplished without the prior. Further, refinement reduces end-effector orientation error across all evaluated tasks. The same posture module improves a pretrained SONIC controller on four of five tasks. Without compliance training, policies tend to lose balance under disturbances rather than sacrifice tracking. On a Unitree G1, OCLO maintains balance under end-effector disturbances that cause its ablations to fail and performs seven loco-manipulation tasks, including crouched walking and picking up a box from a low surface. Project website: https://oclo-humanoid.github.io/

0.27

Low-speed Limit Cycle Walking of Planar X-shaped Bipedal Robot with Special Properties

cs.RO ·2026-11-17 ·Fumihiko Asano, Cong Yan
published similarity 0.62
Abstract · 6 pages, 7 figures. Published in the Proceedings of IEEE ICARM 2023. This author version corrects bibliographic information and minor typogr…

This paper proposes a novel planar semicircular-footed X-shaped bipedal robot in which the center of mass of each leg link is at the same position as the hip joint, and discusses a method for generating a stable limit cycle gait on level ground. First, we outline the assumptions of the robot model with four degrees of freedom, and develop the mathematical equations of motion and collision. Second, we set the relative hip-joint angle as a control output and design a control system to follow it to the desired trajectory specified as a fifth-order function of time. Third, we mathematically show that there are special properties: the angular velocity of the swing leg does not change before and after the collision, and the time-integral of the control input becomes zero in a steady gait. We also mathematically show that the model has the feature that approximate linearization is effective and the antigravity effect of semicircular feet can be utilized. Through numerical simulations, we verify the validity of the theoretical results, and analyze some fundamental gait properties such as convergence speed and mechanical energy restoration.

0.41

Demonstration-Guided Humanoid Stand-Up on an Emulated Deformable Surface

cs.RO ·2026-08-21 ·Aniruddh Kushwah, Vyankatesh Ashtekar, Ashish Dutta
similarity 0.62
Abstract

This paper presents a reference-guided reinforcement learning framework to generate stand-up motion for a 29-DOF Unitree G1 humanoid on deformable soft ground, using a human demonstration recorded on hard ground. The terrain compliance is modelled using solref and solimp parameters from MuJoCo's rigid body soft-contact model. The rewards consists of (i) reference motion tracking through residual joint-position control and (ii) explicit recovery objectives such as pelvis height, torso uprightness, and the final posture. First, the policy is trained with the specified rewards considering hard ground. Next, the terrain stiffness is lowered by updating solref and the nominal surface penetration zone is expanded using solimp. Subsequent training enables the policy to adapt to the delayed support force generation due to significant surface penetration during contact-intensive phases while preserving the original demonstration pattern. The learned policy successfully completes the fallen-to-standing task in simulation, reaching the targeted pelvis height and uprightness, with a maximum contact penetration of approximately 40 mm during the process. The proposed method is demonstrated on two stand-up sequences and successfully achieves the final recovery objective on both hard and soft ground. Ablation studies show that reference tracking alone is insufficient for successful stand-up, and that explicit recovery rewards are essential.

0.24

FORGE: Feasible Online Reduced-Order Reference Generation and Whole-Body Execution for Agile Humanoid Locomotion

cs.RO cs.LG ·2026-10-27 ·Adrian B. Ghansah, Yujin An, Jeeseop Kim, Soon-Jo Chung
published similarity 0.61
Abstract · 8 pages, 6 figures. Accepted to the 2026 IEEE-RAS 25th International Conference on Humanoid Robots (Humanoids)

This paper presents a two-stage learning framework for versatile and agile humanoid locomotion that couples online reduced-order model (ROM) reference generation with whole-body tracking control. In the first stage, we train a command-conditioned whole-body reference generator using single rigid body dynamics combined with full humanoid kinematics. In the second stage, the frozen ROM policy is rolled out online to generate references for training a whole-body tracking policy on the full-order dynamics model. Learning a kino-dynamically consistent reference generator in the simplified ROM space enables us to generate references over a broad command space and over multiple locomotion strategies using a single unified framework. We demonstrate the approach on a Unitree G1 humanoid robot, achieving longitudinal velocities from -2.0 m/s to 2.8 m/s, lateral velocities up to +-1.0 m/s, angular velocities up to +-3.0 rad/s, one-legged hopping, and continuous transitions across the commands, all using one unified reference policy and one whole-body tracking policy.

0.23

BRIDGE: An Open-Source Humanoid Platform via Morphology-Control Co-Design for Physical AI

cs.RO cs.AI ·2026-09-03 ·Jianren Wang, Letian Qian, Zikai Wang, Weiwei Wu, Junjie Zong +2 more
code/data similarity 0.60
Abstract

Developing humanoid robots capable of leveraging human behavioral data is essential for general-purpose embodiment, yet conventional development remains bottlenecked by a decoupled paradigm that isolates hardware design from whole-body control. This approach leads to suboptimal systems that compromise human-like fluidity and agility. To bridge this gap, we introduce a data-driven morphology-control co-design framework that optimizes humanoid morphology for human-like movement. To quantify morphological fidelity, we also introduce a novel metric that jointly considers kinematic retargeting fidelity to human motion and dynamic tracking performance. Our framework achieves state-of-the-art (SOTA) performance across all metrics compared to baseline humanoids (Bumi, K1, and Toddlerbot). Finally, we realize this design in Bridge, an open-source, 88cm-tall humanoid platform released alongside its control policy. We demonstrate that Bridge captures human motion data with superior fidelity, exhibiting exceptional performance across foundational locomotion, robust balance, and highly dynamic maneuvers. Videos and open-source materials: https://sites.google.com/view/bridgerobot.

0.46