CS Paper Radar

Design and Analysis of a Nonlinear Parallel Mechanism Coupling for Dynamic Humanoid Legs

Rohit Kumar, Heiner Peters, Felix Wiebe, Franek Stark, Janne Janzen, Dennis Mronga, Shubham Vyas, Frank Kirchner

cs.RO ·submitted 2026-10-12 11:22 UTC · v2

Abstract

Humanoids increasingly demand lightweight leg mechanisms for agile, dynamic, and energy-efficient locomotion. Reducing distal inertia through proximal actuation has thus become a common design goal. Yet, compact transmissions that preserve torque capability and efficient force transmission remain hard to achieve. This paper presents a novel series-parallel leg design combining a knee parallel mechanism, an ankle parallel mechanism, and a nonlinear knee-ankle coupling where all actuators placed closer to the hip. As the knee flexes, the coupling passively assists ankle dorsiflexion for foot clearance and, as it extends it assists plantarflexion for push-off, redistributing ankle load through the knee transmission. We derive the coupling's nonlinear transmission models and validate them in simulation and on hardware. The design shows that the shared transmission lets both joints draw on each other's actuator capacity by easing the knee's peak torque demand under load and the ankle's peak speed demand during fast motion. With the leg's proximal actuator placement, the leg achieves an effective reflected mass of 0.37 kg at the foot for a 6 kg leg, demonstrating very low distal leg inertia for dynamic humanoid robots.

Closest papers

Nearest neighbours by meaning across the whole index.

A Dual-Cam Parallel Elastic Actuator with Shared Gas-Spring Compensation for Humanoid Ankles

cs.RO ·2026-08-31 ·Jingcheng Jiang, Yifang Zhang, Nikos G. Tsagarakis
published similarity 0.74
Abstract · Accepted to IEEE AIM 2026. Copyright 2026 IEEE. Personal use of this material is permitted

To improve torque capacity and energy efficiency of humanoid ankles, this paper proposes a 2-DoF parallel elastic actuator (PEA). The main novelty of the proposed design lies in its dual-cam, single-gas-spring architecture, which enables torque compensation in both pitch and roll using a shared elastic element, thereby improving structural compactness compared with conventional multi-element compensation schemes. By leveraging parallel gas springs and customized cam modules, the proposed architecture provides dual-axis torque assistance tailored to specific task requirements. The second key contribution is the formulation of a coupled 2-DoF mathematical model that explicitly captures the interdependence between the two compensation units through the shared spring. Based on this model, an optimization-based design framework is developed to synthesize customized cam profiles from prescribed torque references, establishing a systematic link from task requirements to hardware realization. The complete lower-leg CAD integration is presented in detail. Static FEA and kinematic simulations confirm the design's feasibility and torque-relief effectiveness. The results highlight the proposed design as a compact, customizable solution for 2-DoF humanoid ankle torque compensation.

0.48

Modeling and Control of a Rigid-soft Hybrid-link Humanoid Robot

cs.RO ·2026-10-10 ·Zewen He, Taiki Ishigaki, Ko Yamamoto
published similarity 0.64
Abstract

Physical flexibility plays a significant role not only in human motions but also in robot motions. For example, a humanoid robot with passive and flexible elements, which can be regarded as a rigid--soft hybrid-link system, has the advantages of storing energy and mitigating impact in a dynamic motion. However, the motion design and control of a hybrid-link system are challenging to achieve and have only been discussed in the literature. In this study, we propose the framework of inverse kinematics and compliance optimization-based control for a hybrid-link humanoid system that represents the continuous deformation of a flexible structure using the piece-wise constant strain (PCS) model. The proposed method was validated using forward dynamics simulations for standing, jumping, and walking motions. Then, we built an experimental setup using a biped humanoid robot with leaf-spring type prosthesis leg, in which the prosthesis deformation was measured by a motion capture system. Using this setup, we experimentally validated the proposed method for standing balance control in both double- and single-support cases.

0.45

Hip Energized Monopedal Hopping

cs.RO ·2026-08-11 ·Shane Rozen-Levy, Griffon McMahon, Daniel Koditschek
similarity 0.63
Abstract · 35 pages, 11 figures

We present a novel stepping strategy for pitch unlocked planar monopeds where the reaction torques from stabilizing pitch with a conventional PD + feedfoward controller are recruited to counteract energetic losses from damping. By moving the location of the mass center, our controller increases the pitch stabilization torque, thereby adding energy to the gait. A new stepping policy adjusts the distribution of energy between the radial and angular degrees of freedom to counteract dissipative losses and achieve a user specified balance between steady state fore-aft speed and apex height. Hybrid averaging analysis yields closed form expressions for the fixed points and eigenvalues of the resulting gait, lending insight into the interplay between the physical and control parameters' influence on performance. Simulation studies on a generic 5 link biped and a careful model of the Penn Jerboa reveal a useful correspondence to these analytical predictions. Physical experiments on the Penn Jerboa exhibit stable locomotion with speeds ranging from 1.02 m/s to 1.77 m/s (5.10 leg lengths/s to 8.85 leg lengths/s) in a manner effectively approximated by the mathematical analysis.

0.10

Optimization Design and Simulation Validation of a Variable Stiffness Actuator Based on a Crossed Four-Bar Mechanism

eess.SY ·2026-09-16 ·Yuanlong Ji, Ruizhe Jiang, Xiangyu Xie, Junheng Lin, Dongrun Jin +1 more
published similarity 0.63
Abstract · 7 pages, 5 figures

This paper presents a bio-inspired antagonistic variable stiffness actuator (VSA) based on two crossed four-bar compliant transmission elastic units (CFB-CTEs). The design addresses the difficulty of combining nonlinear elastic shaping with low structural inertia in antagonistic VSA mechanisms. Inspired by the crossed constraint behavior of the anterior and posterior cruciate ligaments during knee flexion, the proposed actuator uses geometric transmission, elastic energy storage, and bilateral antagonistic arrangement to shape the output torque and equivalent stiffness. A multi-objective optimization model is established to balance torque tracking accuracy, equivalent inertia, and mass. The selected compromise design achieved a torque root-mean-square error (RMSE) of $0.883~\mathrm{N\,mm}$ and a total mass of $50.2~\mathrm{g}$. Its average equivalent inertia was reduced by about 78% compared with an independent torque-only optimized design. An ADAMS multibody model was further built to verify the structural response under single-input, opposite-input, and same-input conditions. The results support the feasibility of the proposed crossed four-bar elastic unit as a lightweight nonlinear elastic branch for antagonistic VSAs.

0.68

Breaking speed scaling in quadrupedal robots via Huygens' coupled-pendulum dynamics

cs.RO ·2026-09-09 ·Yucheng Tao, Yongbin Jin, Shaowen Cheng, Xianwei Liu, Yanyan Yuan +6 more
similarity 0.61
Abstract

Achieving biological-level running speeds has largely been pursued through advances in control algorithms, which improve the utilization of existing hardware. However, the ultimate speed limits remain governed by the underlying force and torque requirements of rapid locomotion, which are typically addressed through increased actuator capacity. Inspired by Huygens' coupled pendulums, we demonstrate that superior locomotion can emerge from principled exploitation of intrinsic dynamics rather than brute-force hardware scaling. Inter-limb inertial coupling redistributes energy across the gait cycle and reduces peak joint torque required for rapid periodic motion, thereby expanding the achievable speed without proportional increases in actuator capability. Incorporating hardware parameters as additional design variables further extends this analysis into a co-optimization framework, enabling the systematic utilization of inertial coupling in robot design. Guided by this framework, a quadruped robot achieves a running speed of 10.74 m/s (Froude number 21.4) and completes a 100-meter sprint in 12.2 seconds, representing the first legged robot to surpass 10 m/s. These results establish inertial coupling as an underlying mechanism governing high-speed legged locomotion and highlight its role in reducing force requirements, offering new insights into the design of agile robotic systems.

0.24

When to Waddle: A Comparative Study of Bipedal Torso-Stabilization on Low-Friction Surfaces

cs.RO ·2026-09-18 ·Ben Gu, Naomi Oke, George Ortiz, Stacy Ashlyn, Cordelia Pride +2 more
similarity 0.61
Abstract

Low-friction surfaces challenge bipedal locomotion by limiting the contact forces available during stepping. Inspired by penguin waddling, we investigate how lateral torso motion and center of mass (COM) placement affect locomotion as surface friction changes. Using a five-actuator biped, we compare an upright-gait strategy with a penguin-inspired torso-over-stance-leg strategy across multiple COM placements in simulation and hardware. In the 3-D simulator MuJoCo, we sweep through sinusoidal leg and hip actuation parameters across four friction coefficients mu = 0.1, 0.3, 0.5, 0.7. In simulation, torso-over-stance-leg motion produces more successful controllers and higher forward speeds at low friction, with the highest speed occurring for the high-COM configuration. Hardware experiments show the same low-friction speed trend: at mu=0.12, torso-over-stance-leg motion increases forward speed and reduces cost of transport at both tested COM ratios, and the higher COM also improves both measures. The high-COM penguin configuration is the fastest and most energy efficient while maintaining low sideways foot motion. At mu=0.45, the COM trend reverses: the lower-COM configurations are faster and more energy efficient, while gait strategy has little effect on forward speed but still changes sideways foot motion. These results show that the effects of lateral torso motion and COM placement depend on the available friction, and that forward speed, energy use, and slip-related foot motion can be modulated with a penguin-inspired torso motion on hardware.

0.22

Spiderbot: An Open-Source Energy-Efficient Hexapod with Passive Gravity Compensation

cs.RO eess.SY ·2026-09-22 ·Ritwik Sharma, Vimarsh Shah, Saransh Agrawal
code/data similarity 0.60
Abstract · 8 pages

Hexapod robots can achieve static stability with fewer actuated joints than bipeds or quadrupeds, yet many platforms still use 3-DOF legs, increasing weight and continuous torque requirement with limited gain in locomotion capability on flat, inclined and moderately rough terrains. We release Spiderbot, an open-source hexapod that uses a 4-bar linkage with a passive spring to mechanically support body weight, with a 2-DOF per-leg design that substantially reduces energy consumption. This mechanism substantially offloads gravitational torque during standing stance consuming only 1.5W (reduction of over 90\% over the unsprung version and up to 96\% over other similar hexapods). The passive spring compensation extends to payloads of up to 3.25kg with no additional torque requirements. The platform enables long-duration deployments on a modest battery budget and costs under \$400, making it suitable for large-scale multi-agent experiments. We validate the locomotion capabilities of the platform with an RL policy trained in mjlab, including successful sim-to-real transfer, despite the complexity of the mechanism. The platform is evaluated on flat and rough terrains, slope up to $15^\circ$ and step obstacles. We release all the CAD files, assembling instructions, and full training and deployment code along with the model checkpoints at https://erc-bpgc.github.io/SpiderBot/.

0.27

Contact-Constrained Lower-Limb Joint-Offset Calibration for Humanoid Robots

cs.RO ·2026-09-02 ·Kaixiang Lu, Haiyu Lan, Chunxiao Qiao, You Li, Chengyuan Luo +3 more
top venue similarity 0.59
Abstract

Accurate joint encoder offsets are essential for kinematic consistency in humanoid lower limbs, yet existing calibration methods typically require external motion-capture systems or fiducial targets. We present a self-contained calibration framework exploiting only onboard joint encoders and a pelvis-mounted IMU during static double-support contact. The inter-foot transform from forward kinematics must stay constant when both feet are fixed; minimizing its posture-dependent dispersion yields a nonlinear least-squares problem over the 12-dimensional offset vector. A Hessian eigenstructure analysis shows that parallel pitch axes induce a rotational coupling. Orientation residuals then observe only the pitch-offset sum, while translation and posture diversity set the remaining numerical observability. For the A3 pitch-to-roll-to-yaw ordering, hip-roll and hip-yaw excitation reduce hip-pitch coupling. A standing-posture knee prior then anchors the remaining weak pitch-chain decomposition. Simulation and real-machine injection tests show consistent recovery, and on held-out recordings calibration reduces foot-height RMS residuals from 4.26 to 2.20 mm on A3 and from 8.03 to 1.43 mm on A2. An independent LiDAR-inertial reference checks the pitch-coupled channel. Removing an injected pitch offset moves the leg-odometry vertical drift back toward the LiDAR trajectory. A few static double-support stances thus provide contact-consistent corrections for well-excited directions. Individual offsets in the weak pitch chain remain prior-dependent.

0.44