CS Paper Radar

Impedance Cloning: Learning Equilibrium Point Parameters for Contact-Rich Manipulation

Hayato Takahashi, Ryoga Oishi, Yuki Kasuga, Toshiaki Tsuji

cs.RO ·submitted 2026-09-25 05:36 UTC · v1

Abstract

Contact-rich manipulation requires robots to regulate force against surfaces whose geometry deviates unpredictably from training conditions. Trajectory-based imitation learning, which reproduces observable outputs, breaks down under such shifts. We propose Impedance Cloning, which instead imitates the biomechanical priors that generate motion -- the stiffness and equilibrium point -- and thereby passively absorbs contact uncertainty. Because these parameters encode intent rather than outcome, they generalize across surface geometries where trajectory reproduction does not. We extract them from bilateral teleoperation demonstrations via a particle filter without force/torque sensors and evaluate the framework on two CRANE-X7 manipulators. In a wiping task with joint-space actions, the trajectory-based baseline loses contact below -6 cm, whereas the proposed method maintains a consistent 4-5 N contact force above -6 cm, with a gradual decrease below; with Cartesian-space actions, its force-height slope over 0 to +8 cm is 0.13 +/- 0.03 N/cm, versus 0.34-0.83 N/cm for fixed-impedance baselines. In a pick-and-place task with 10 diverse cups (100 trials), the proposed method succeeds in 84 trials, outperforming the fixed-impedance baseline (74/100) and performing comparably to a variable impedance control baseline (82/100) with one demonstration instead of ten. In a grasping task, the representation reduces torque tracking error with both ILBiT and Mamba backbones, confirming its generality across architectures.

Comment
8 pages, 7 figures, 3 tables. Submitted to IEEE Robotics and Automation Letters (RA-L)

Closest papers

Nearest neighbours by meaning across the whole index.

Learning Reflexive Behavior for Contact-Rich Manipulation

cs.RO ·2026-10-02 ·Quan Nguyen, Yunho Kim, Joonho Lee
similarity 0.78
Abstract

During contact-rich manipulation, interactions between a robot and its environment carry information about local geometry: a surface prevents penetration, a bore guides a peg. A controller that exploits these interactions can comply with environmental constraints while preserving task intent. Robot-earning systems commonly use position, hybrid force-position, or Cartesian impedance control. Their prescribed tracking objectives, stiffness, or force-control directions may not match local constraints and may degrade performance. We learn a proprioceptive reflex policy in simulation on three simple interaction primitives: a spring, a plane, and a rail. The policy maps task-space commands to joint-position targets using state history, without direct force or geometrical measurements. Once trained, it serves as a frozen execution layer beneath higher-level controllers. We evaluate it in dual-arm box lifting, peg insertion, and surface following. In box lifting, the reflex kept the force below the threshold while the baseline failed. In rough-surface following it stayed below the 10 N reference, on par with tuned hybrid force-position control. In 0.02 mm peg insertion It reduced mean estimated contact force to less than half that of the baseline while increasing hardware success rates from at most 22 % to 36-58 %. By separating contact response from command generation, the reflex policy provides motion planners, learned policies, and teleoperators with robust contact-rich execution.

0.15

ImpedanceMimic: Learned Impedance as Action Space for Force-Accurate Motion Imitation

cs.RO cs.GRcs.LG ·2026-11-14 ·Matthias Jammot, Pembe Gizem Özdil
code/data similarity 0.78
Abstract · 39 pages, 13 figures, 28 tables. Project page: https://impedancemimic.github.io/ImpedanceMimic/

Recovering the forces behind a motion is ill-posed: different controllers can reproduce the same movement while generating different contact forces. Physics-based motion imitation resolves this ambiguity through simulation, but relies on fixed-gain proportional-derivative (PD) control. We show that fixed gains impose a trade-off between motion and force tracking, as contact and swing place conflicting demands on joint stiffness and damping. We introduce ImpedanceMimic, a reinforcement-learning policy that modulates per-joint stiffness, damping, and position setpoints from motion and force measurements, but requires only motion at inference. Across 129 participants and six activities, ImpedanceMimic outperforms matched fixed-gain PD under every integration scheme, direct-torque, muscle-actuated and existing imitation controllers in kinematic and force fidelity, approaching a dedicated motion-to-force regressor. By expressing gains as multiples of inertia-scaled priors, a single policy controls subject-specific biomechanical models without explicit anthropometric input and transfers zero-shot to unseen humans and a humanoid robot. The learned impedance forms a low-dimensional representation of motor state, shared across bodies, that generalizes to withheld activities: stiffness scales with load, and damping anticipates unloading.

0.17

One Demonstration, Many Objects: Generalizing Manipulation via Local Contact Geometry

cs.RO ·2026-09-01 ·Satvik Sharma, Samrat Sahoo, Huang Huang, Fei-Fei Li, Jiajun Wu +2 more
highly cited similarity 0.77
Abstract

Dexterous manipulation with multi-fingered robot hands promises human-level dexterity, but collecting large-scale dexterous robot hand data remains difficult. Learning from human demonstrations has emerged as a scalable alternative to robot teleoperation, providing strong priors on object interaction and contact strategies. Recent sim-to-real RL methods incorporate such priors, but often (i) omit rewards that explicitly incentivize precise contact, yielding weak real-world performance, and/or (ii) generalize poorly to unseen object instances. We propose DemoMimic (Dexterous Motion Mimic), a policy that manipulates objects by focusing on their geometry local to the contact points. Its contact-centric rewards encourage precise contact and improve sim-to-real consistency, yielding a single real-world policy that transfers across objects of varying shape, scale, mass, and friction wherever local contact structure is preserved. Real-world ablations show that DemoMimic achieves 71% success across 16 objects, four tasks, and two robot-hand embodiments, with the smallest sim-to-real drop compared to baselines.

0.36

Imp-ACT: Adaptive Impedance Control and Action Chunking with Transformers to Learn Contact-Rich Manipulation from Demonstrations

cs.RO ·2026-09-25 ·Luca Zanetti, Doganay Sirintuna, Idil Ozdamar, Pietro Balatti, Heng Zhang +1 more
similarity 0.77
Abstract · 9 pages, 5 figures, submitted to IEEE International Conference on Robotics & Automation 2027, for associated video see https://youtu.be/iAu_…

Contact-rich manipulation requires robots to balance accurate motion tracking with compliant interaction, yet most visual-action policies leave compliance fixed at the controller level. We present Imp-ACT, a methodologically grounded and practical approach to incorporating direction-dependent Cartesian stiffness modulation directly into demonstration collection, without manual stiffness selection or offline target reconstruction. During teleoperation, a self-tuning impedance controller adapts stiffness along the instantaneous direction of motion while maintaining compliance in orthogonal directions. The adapted stiffness is applied and recorded alongside visual observations and motion commands, capturing motion and compliance under the same dynamics. We implement this pipeline using Action Chunking with Transformer (ACT) to predict end-effector pose, gripper action, and motion-direction stiffness from visual, proprioceptive, and wrench observations. The performance of Imp-ACT is evaluated on wiping and plug insertion using both success rate and quantitative measures of contact behavior. Compared with fixed low- and high-stiffness baselines, Imp-ACT achieves comparable or higher success while maintaining low interaction forces. In wiping, it reduces contact-force vibration by approximately $29\times$ relative to the compliant baseline and $180\times$ relative to the stiff baseline. In plug insertion, it reduces forces orthogonal to the insertion direction by $43\%$ relative to the better fixed-stiffness baseline. These results highlight the benefit of maintaining sufficient stiffness along the direction needed for task execution while preserving compliance in other directions to limit contact forces and accommodate environmental constraints.

0.32

FOMI: A Force-Feedback Manipulation Interface for Teaching Contact-Rich Manipulation

cs.RO ·2026-10-14 ·Yishu Shen, Yiming Luo, Ruilin Wang, Bowen Yang, Shuai Yang +5 more
similarity 0.75
Abstract

Robot-free collection with handheld interfaces enables scalable acquisition of human demonstrations for policy learning. However, existing handheld interfaces often provide limited intuitive force feedback, making contact-rich demonstration collection challenging for human operators. To address this, we present FOMI, a force-feedback manipulation interface with a scissor-shaped mechanism, which transmits object interaction forces directly to the operator's hands through actuation links without force sensors. This intuitive force feedback supports real-time action adjustment during robot-free collection of contact-rich demonstrations. Around FOMI, we build a demonstration collection system that integrates sensor calibration, data acquisition, and synchronization for robot-free collection. By further mapping pose changes and gripper opening of FOMI to robot end-effector poses and gripper commands, the system also supports teleoperation. Across four contact-rich tasks, FOMI improves collection efficiency by approximately 29% and 18% over the best baselines in robot-free collection and teleoperation, respectively. Demonstrations collected with FOMI in both modes enable policies to perform challenging contact-rich manipulation tasks with high success rates.

0.32

Force-Modulated Dexterity: Unified Compliance for Contact-Rich Manipulation

cs.RO cs.AI ·2026-10-12 ·Ying Yuan, David Held, Jitendra Malik, Haozhi Qi
code/data similarity 0.75
Abstract · Project page: https://yingyuan0414.github.io/fomo-dex/

Teleoperation is widely used to collect high-quality demonstrations for robot learning. Dexterous manipulation, however, requires coordinated control of motion and contact forces. Operators can specify motion, but struggle to reproduce the subtle force adjustments of human manipulation without feeling the robot's contacts. We introduce Force-Modulated Dexterity (FOMO-Dex), a unified compliance formulation for contact-rich manipulation. FOMO-Dex expresses nominal actions in coordinates defined by task geometry and contact structure. It applies force-driven motion corrections along selected directions while leaving the remaining command components unchanged. Across card picking, paper cutting, screwdriving, and nut-and-bolt assembly, FOMO-Dex reduces excessive contact forces compared with stiff control. A user study shows that operators collect more successful demonstration data per hour after brief practice. For policy learning, imitating the corrected actions improves card-picking success over imitating raw operator commands. Policies trained on FOMO-Dex demonstrations also achieve more rotation in nut-and-bolt manipulation and screwdriving than those trained on demonstrations collected with the stiff controller. Videos are shown on https://yingyuan0414.github.io/fomo-dex/ .

0.41

Wrench-ACT: Enhancing Robot Policies for Contact Rich Behavior Using Direct Wrench Control

cs.RO ·2026-09-29 ·Johannes Hechtl, Yannik Blei, Simon Ball, Reihaneh Mirjalili, Michael Krawez +3 more
similarity 0.75
Abstract

While contact-rich manipulation requires deliberate regulation of interaction forces, recent approaches to robot manipulation learning predominantly represent actions as target positions or poses. Even methods that incorporate force sensing either use it solely as an observation or, when predicting forces as part of the output, rely on a hybrid force controller. In this paper, we propose an imitation learning policy that predicts wrenches as its sole action output for direct use by a pure force controller. Our studies suggest that force-domain imitation learning depends critically on data collection, with force-feedback teleoperation improving policy performance by capturing the operator's deliberate force regulation. Using Action Chunking with Transformers (ACT) as the base architecture, we train single-task models on bilateral wrench demonstrations and evaluate them on five contact-rich manipulation tasks. The wrench policy matches or outperforms position-based baselines across all tasks, with gains varying according to the degree of deliberate force regulation each task requires. Cross-condition ablations show that the bilateral data collection interface and the wrench action space each contribute independently to performance. To support further research, we will release over 1000 wrench-action demonstrations spanning these tasks on a companion website upon publication.

0.16

Contact-Aware Imitation Learning Through Contact Factorization

cs.RO ·2026-10-07 ·Jiho Hong, Daeun Song, Sanghyun Kim, Mingyo Seo
code/data similarity 0.75
Abstract

Generalizable contact-rich manipulation requires robots to preserve intended task behavior while adapting its physical realization to changing contact conditions. However, interaction forces can vary substantially with small changes in surface geometry, orientation, and friction, making policies trained directly on raw force measurements difficult to transfer beyond demonstrated conditions. We introduce FACE, a contact-factorized imitation learning framework that separates intended task behavior from environment-dependent contact factors. Our representation expresses interaction forces in normalized, contact-relative coordinates, while a learned contact-normal estimator and an online friction estimator infer the local contact normal and effective friction scale. Together, these estimators enable force observations to be encoded and policy outputs to be decoded into physical motion and force commands during execution. In this way, FACE adapts execution to current contact conditions while preserving the intended task behavior, without updating the policy parameters. We evaluate FACE on real-robot contact-rich manipulation under unseen variations in surface properties and geometry, demonstrating robust generalization across contact conditions through controlled comparisons with variants that adapt prior approaches to our setting. Videos and additional materials can be found on the project page: https://rcilab.khu.ac.kr/face.

0.28