CS Paper Radar

S-ALSA: Co-Design of Adiabatic Logic-based Sensing and Balanced Bit-Cells for Secure and Energy-Efficient MRAM

Wu Yang, Amit Degada, Himanshu Thapliyal

cs.AR ·submitted 2026-09-27 14:35 UTC · v1

Abstract

Magnetoresistive Random Access Memory (MRAM) technologies such as Spin-Transfer Torque (STT-MRAM) and Spin-Orbit Torque assisted (SOT-STT-MRAM) offer nonvolatility and low leakage, making them attractive for IoT systems. However, conventional MRAM read circuits face two fundamental challenges: high dynamic energy consumption and vulnerability to side-channel attacks caused by data-dependent current variations in Magnetic Tunnel Junctions (MTJs). This paper presents a Secured Adiabatic Logic Sense Amplifier (SALSA) that addresses both challenges simultaneously through circuit-device co-design. S-ALSA combines structural current balancing via a 4T-2MTJ bit cell, which eliminates read current asymmetry at the storage level, with dynamic power equalization via adiabatic charge recovery in the sensing circuit. The proposed architecture supports both STT-MRAM and SOT-STT-MRAM. Case studies using 4x4 MRAM macros shows up to 80% energy savings over conventional Pre-Charge Sense Amplifiers (PCSA) across IoT frequencies. Correlation Power Analysis (CPA) attacks on PRESENT-80 encryption confirm complete suppression of key leakage when S-ALSA is combined with a balanced bit cell. This work establishes a unified framework where energy efficiency and hardware security are achieved simultaneously, enabling secure and low-power IoT memory design.

Comment
6 pages; 2026 IEEE Computer Society Annual Symposium on VLSI, July 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Design Space Exploration of In-Memory Computing Implementations for Discrete Fourier Transform

eess.SP ·2026-09-18 ·Sofia Tatidis, Philip Nielsen, Liang Liu, Mojtaba Mahdavi
similarity 0.61
Abstract

Although memristor-based in-memory computing (IMC) has been widely investigated for brain-inspired neuromorphic workloads, systematic evaluations of its energy, latency, and signal-to-noise ratio (SNR) trade-offs across diverse system parameters remain scarce for classical digital signal processing (DSP). To address this gap, this paper introduces a comprehensive hardware-aware design framework for systematically mapping algorithmic workloads onto IMC architectures, using the discrete Fourier transform (DFT) as a case study. Tailored to the stringent performance requirements of a DFT accelerator for 5G orthogonal frequency-division multiplexing (OFDM) systems, we propose a novel mapping scheme that reduces energy consumption per computation by 53% compared with conventional mapping techniques. Additionally, we present a comparative study of resistive random-access memory (RRAM) and ferroelectric tunnel junction (FTJ) technologies with identical numbers of programmable states but distinct conductance ranges, demonstrating the importance of device-informed architectural co-design. By bridging the gap between emerging IMC architectures and rigid DSP constraints, this work provides a pathway toward energy-efficient edge accelerators for future wireless communication systems.

0.12

Understanding the Power Consumption of Modern High Bandwidth Memory: Experimental Analysis and Modeling Using Real HBM2 DRAM Chips

cs.AR cs.PF ·2026-10-09 ·Ataberk Olgun, Spiros Galanopoulos, Andreas Kosmas Kakolyris, İsmail Emir Yüksel, Haocong Luo +2 more
top venuecode/data similarity 0.54
Abstract · Extended version of the paper titled "Understanding the Power Consumption of Modern High Bandwidth Memory: Experimental Analysis and Modelin…

We perform the first comprehensive experimental characterization of power consumed by real HBM2 DRAM chips. Our extensive characterization yields 1) the empirical basis for developing new, accurate HBM power models or validating existing power models and 2) key insights into structural and data-pattern-dependent variation of power in HBM2 chips. Out of our 13 new findings and 6 key takeaway messages, we highlight: 1) a read operation consumes significantly higher current than any other operation and 2) the toggled data bus signals in a data transfer burst significantly affect current draw where toggling all HBM2-internal bank group bus signals causes 29.4% higher power consumption than keeping them constant. Leveraging our empirical insights into HBM2 power consumption, we engineer an access pattern that yields 23.6% higher power consumption on average across 36 tested HBM2 chips than the highest-power-consuming JEDEC-specified current measurement loop. Our results have important implications for HBM-based system design and validation. Relying solely on JEDEC- or vendor-specified test loops to bound HBM power could cause system failures and/or thermal throttling in real-world high-power AI/ML workloads. To improve 3D-stacked DRAM power modeling in open source architectural simulation infrastructures, we develop a new HBM power model. Our model predicts the power of 36 real HBM2 chips across diverse workloads (including a real LLM decode workload) with 7.6 -- 8.1% mean absolute percentage error, substantially more accurately than state-of-the-art HBM power models. The power consumption predicted by our model for a power-intensive microbenchmark closely matches (with 2.4% to 5.3% error across HBM3E's specified supply voltage range) the average HBM3E memory power consumed by three tested NVIDIA H200 GPUs. We publicly release our power model at https://github.com/CMU-SAFARI/HBM-Power.

0.56

OTTER - Two Transistor - One RRAM Architecture for Reliable In-Memory-Computing in 28 nm CMOS Technology

cs.ET ·2026-09-08 ·Yang Chen, Daniele Storelli, Xinyi Zhao, Ankit Bende, Paul-Philipp Manea +18 more
similarity 0.54
Abstract

This work presents OTTER, a 28 nm CMOS platform co-integrated with TaOx-based valence-change mechanism (VCM) RRAM, demonstrating a two-transistor-one-memristive-device (2T1R) architecture for reliable in-memory computing. The 2T1R cell combines a low-drive-current (LD) transistor and a high-drive-current (HD) transistor in parallel, providing dedicated bias paths for SET programming and RESET operation, respectively. Through systematic experimental and simulated comparison of various transistor-pairing configurations using the physical compact model JART VCM Rth, design guidelines for transistor sizing are derived, establishing the minimum RESET transistor W/L required for complete RESET as a function of the SET current compliance. The 2T1R cell is further characterized under pulse-based programming, demonstrating multilevel analog conductance tuning with narrow, well separated conductance states across six programmable levels. An analog content-addressable memory (aCAM) design based on the same 2T1R cell is additionally analyzed at the circuit level, evaluating trade-offs between top- and bottom-connected RRAM comparator configurations. A hardware implementation of compute-in-memory (CIM) multiply-and-accumulate (MAC) operations is further demonstrated on a 15 x 15 2T1R crossbar array.

0.29

A Time-Based Readout for Vector-Matrix Multiplication in Fully Analog Memristive SNNs

cs.ET cs.AIcs.AR ·2026-09-10 ·Elia Mateu-Barriendos, Álvaro Gómez-Pau, Josep Rius, Daniel Arumí, Rosa Rodríguez-Montañés +1 more
published similarity 0.53
Abstract · Accepted at 2026 IEEE 33rd International Conference on Electronics, Circuits and Systems (ICECS)

Artificial neural networks rely on vector-matrix multiplications (VMMs), whose implementation in von Neumann architectures is dominated by costly data movement between memory and processing units. Spiking neural networks (SNNs) mitigate this bottleneck by performing in-memory, analog VMMs using memristive crossbar arrays. However, conventional current-mode readout circuits incur significant area and power overhead. This work proposes a fully analog readout architecture based on voltage-to-time conversion of the VMM output. By sensing the column voltage, the proposed approach avoids current-mode summing and scaling circuitry, improving area and energy efficiency. Post-layout simulations of a 10x1 SNN implemented in a 130 nm CMOS technology validate the proposed architecture, while application to a trained 64x10 SNN for digit classification further demonstrates its feasibility for SNN inference.

0.51

FALCON: Fault-Tolerant Magnetic Tunnel Junction-Based In-Memory Stochastic Architecture for Reliability-Critical Edge AI Applications

cs.ET cs.AReess.IV ·2026-09-01 ·Farzad Razi, Mehran Moghadam, Sercan Aygun, M. Hassan Najafi, Marc Riedel
similarity 0.53
Abstract

As modern data-centric applications such as neural inference and sensor-edge analytics expand, they increasingly encounter the von Neumann memory wall, suffering from excessive data movement overhead and stringent energy constraints. In-Memory Computing (IMC) utilizing emerging non-volatile technologies, such as Magnetic Tunnel Junctions (MTJs), promises to mitigate these bottlenecks. However, conventional binary radix-based IMC architectures suffer from excessive vulnerability to process-induced variations, restricted operating margins, and thermal noise. To bridge the gap between energy efficiency and computational reliability, this work proposes FALCON, a fault-tolerant, MTJ-based in-memory arithmetic architecture integrated with Stochastic Computing (SC). By encoding numerical values into uniform bit-streams, SC naturally absorbs localized soft errors and enables the execution of an essential suite of arithmetic operations using highly compact logic primitives directly within the memory arrays. FALCON integrates a deterministic bit mapping mechanism with reconfigurable logic-in-memory (LIM) structures, eliminating the need to transfer data to external processors or area- and power-hungry random number generators. Experimental results using 14 nm FinFET technology validate the correct functionality of FALCON even under aggressive voltage scaling, severe process variation, and noise injection levels up to 30%, making it a robust framework for reliability-critical edge AI applications. We investigate the proper functionality of FALCON on morphological closing as a realistic noise-tolerant image processing case study.

0.36

RRAM circuit-enabled nonlinear precoding and bit precision analysis

eess.SP ·2026-08-15 ·Yuhao Zhang, Haifan Yin, Tao Wang, Jindiao Huang, Kewei Zhu
top venuetheory similarity 0.52
Abstract · 15 pages, 13 figures. Accepted for publication in IEEE Transactions on Communications

The rising number of users and antennas imposes exponentially growing computational loads on future communication systems. Yet conventional processors are facing a bottleneck for their nature of memory-computing separation. In-memory computing (IMC) emerges as a promising solution leveraging its intrinsic high parallelism. This work proposes an IMC architecture that employs resistive random access memory (RRAM) to reduce the computational complexity of the nonlinear Tomlinson-Harashima precoding (THP) to a linear scale. We present a computation-constraint principle for designing RRAM circuits to perform nonlinear matrix operations and construct an LQ decomposition RRAM circuit. Since the conductance of memristor is generally quantized, we perform the bit precision analysis and derive the lower bound of the Signal-to-Interference-plus-Noise Ratio (SINR) and achievable rate. Our analysis indicates that at a high Signal-to-Noise Ratio (SNR) or with a large number of antennas, each 1-bit precision increase yields 6 dB SINR gain and linear rate growth. For practical implementation, we derive the optimal bit precision to sustain SINR performance under varying system configurations. Simulation demonstrates the feasibility and accuracy of the RRAM-based circuit and our theoretical analysis. Our work proves that RRAM-based IMC holds significant potential for high-complexity nonlinear precoding, addressing the escalating computational demands for future communications.

0.35

Evaluating Positive Feedback Adiabatic Logic in 16nm FinFET with a Realistic Power-Clock

cs.AR ·2026-09-17 ·Franciszek Łukowski, Maciej Pyrzowski, Aida Todri-Sanial
similarity 0.51
Abstract · 11 pages, 21 figures, 8 tables

Adiabatic logic reuses the energy stored on load capacitances through quasi-reversible switching, enabling a lower minimum energy consumption than conventional static CMOS. Yet its practicality in FinFET technologies and at multi-GHz clock rates has yet to be investigated. This work provides a systematic evaluation of Positive Feedback Adiabatic Logic (PFAL) simulated in the TSMC 16nm FinFET process. A set of PFAL standard-cell gates were realised, along with two representative combinational circuits - a 2$\times$2 multiplier and a 4-bit comparator - and compared against static CMOS logic using the energy--delay product (EDP) and the energy advantage metric $η= E_{\mathrm{CMOS}} / E_{\mathrm{PFAL}}$. Transient simulations reveal three sources of non-adiabatic loss: two specific to the PMOS/NMOS latch, threshold-voltage-related loss and a previously unreported redundant charging of the output node and one related to the complexity of PFAL logic trees. The low-threshold Buffer/NOT cell achieves a minimum EDP of $1.23\times10^{-26}$J$\cdot$s at $V_{\mathrm{CLK}} = 0.6$V and $f_{\mathrm{CLK}} = 7.94$GHz, while PFAL preserves an energy benefit over static CMOS of up to roughly $5\times$ at reduced frequencies and elevated supply voltages. A parallel-coupled quadrature voltage-controlled oscillator is designed as a realistic four-phase power-clock generator. With this non-ideal supply, the Buffer/NOT energy stays within $2\%$ of the ideal sinusoidal case at $3$GHz. A loading study quantifies the phase shift and amplitude reduction induced by increasing fan-out. Overall, the results provide a design-oriented evaluation of PFAL in 16nm FinFET and a motivation to exploit adiabatic logic for future low-power system architectures.

0.22

A Unified Device-Level Physical Framework for DRAM Read Disturbance

cs.AR cond-mat.mes-hallphysics.app-ph ·2026-11-13 ·Zhaoqiang Bai, Haocong Luo, Xinhe Wang, Xujing Li, Yuelin Jiang +8 more
similarity 0.51
Abstract

Read disturbance in dynamic random-access memory (DRAM) depends on both local device interactions and the electrical conditions imposed by shared array circuitry. Here, we combine DIMM-level characterization results, device measurements, and TCAD simulations to interpret RowHammer, RowPress, and ColumnDisturb within a unified device-level physical framework. We relate charge evolution at the floating storage node to three key mechanisms: trap-assisted electron migration (EM), capacitive coupling (CC), and sense-amplifier-mediated disturb (SAMD). EM is local and trap-sensitive, while CC weakens with wordline separation. SAMD extends disturbance through shared column circuitry by modifying unselected-cell leakage under rail-level bitline biases, a contribution supported by the approximately ninefold higher OFF-state leakage measured relative to retention-like conditions for a high-voltage storage state. These distinct spatial ranges account for localized RowHammer and RowPress failures and remote ColumnDisturb populations with abrupt changes at subarray boundaries. We further interpret prolonged RowPress activation as a transition from an initial RowHammer-like transient to sustained leakage driven mainly by SAMD under held wordline and bitline biases. Within this device-level framework, trap effectiveness and storage-state-dependent leakage provide an interpretation of previously puzzling failure signatures, including the earlier onset of 0-to-1 RowHammer failures despite the predominance of 1-to-0 failures at high hammer counts. The same framework explains the observed RowPress and ColumnDisturb polarities and the duration-dependent reversal of neighboring- and passing-wordline effectiveness. These results provide a physical basis for developing compact DRAM reliability models across access patterns and array configurations.

0.22