CS Paper Radar

A 2-DOF MultiBody Track Joint for Race Car Optimization

Srikanth Sivaramakrishnan, Behzad Danaei, Adwait Verulkar, Ryan Trinter

cs.RO eess.SY ·submitted 2026-10-26 23:41 UTC · v1
unusual

Abstract

TrackJoint is a Modelica MultiBody component that turns a three-dimensional road surface into a joint with two degrees of freedom. The two joint coordinates are the distance travelled along a reference line and the sideways offset from that line. Together they give the position, orientation and angular velocity of a single frame_b connector. All road geometry reaches the joint as a small set of periodic piecewise-quintic splines, so one component can represent any circuit whose splines have been fitted beforehand. The road constraint is closed with d'Alembert's principle. The two generalized forces that belong to the joint coordinates are set to zero, so no Lagrange multipliers are needed. The joint is connected to a multibody race car in Dymola and the pair is exported as one FMI~3.0 FMU. The same FMU is then used for time-domain simulation and for CasADi/IPOPT minimum lap-time optimization, with no change to the model in between. This works because the joint keeps the arc-length coordinate as a real state and publishes its time derivative, which is the quantity that lets the problem be rewritten with distance We report results for minimum lap time simulations on the Singapore Formula~1 circuit.

Comment
American Modelica & FMI Conference 2026

Closest papers

Nearest neighbours by meaning across the whole index.

A Singularity Avoiding Track Model for Race Car Optimization

cs.RO eess.SY ·2026-10-27 ·Adwait Verulkar, Behzad Danaei, Srikanth Sivaramakrishnan, Ryan Trinter
similarity 0.54
Abstract · American Modelica & FMI Conference 2026

A track fitting pipeline is presented that converts a measured racetrack point cloud into a closed, $C^4$ differentiable, three-dimensional surface model suitable for high-fidelity Modelica race-car optimization. The surface is a Monge patch, parametrised by a curvilinear arc-length coordinate measured along the minimum-curvature line (MCL) and a signed lateral offset, with a height polynomial of user-selectable degree capturing the cross-sectional elevation profile. The choice of MCL as the reference line is deliberate since anchoring the same surface on the geometric centre-line can cause adjacent normals to cross inside the drivable region on tight corners. The resulting non-injective parametrisation assigns multiple curvilinear addresses to the same three-dimensional point and returns invalid road geometry. The MCL is obtained from a quadratic program that minimises integrated curvature subject to track-boundary, periodicity, and jerk-regularisation constraints. By reducing total curvature while remaining within the track bounds, the MCL moves the region of parametrisation breakdown outside the drivable strip on all circuits studied, keeps the normal map injective across the full track width, and yields a more linear time-to-arc-length transformation for minimum lap-time problems. The fitted surface and the associated track widths are exported as periodic piecewise-quintic $C^4$ B-splines, solved as a nonlinear program.

0.50

A heuristic for optimal coordination of autonomous vehicles: real-time algorithms

eess.SY ·2026-10-27 ·Saugat Shahi, Jonathan Frey, Filippo Fabiani, Moritz Diehl, Mario Zanon
similarity 0.48
Abstract

When coordinating connected and automated vehicles at an unsignalized intersection, the crossing order and the vehicle trajectories must be decided jointly. For a fixed crossing order, the problem can be formulated conveniently in a bi-level form where each vehicle solves its own optimal control problem, whose optimal value is a function of its entry and exit times, and a coordinator optimizes these times subject to precedence constraints. We compute the first and second order sensitivities of lower-level problems, which are required to solve the upper-level problem, by means of algorithmic differentiation using the real-time software package \texttt{acados}. This implementation exploits tailored algorithms to obtain a computationally efficient implementation of the optimal coordination algorithm. We validate our implementation in numerical simulations that demonstrate both real-time feasibility and effectiveness of our algorithm.

0.59

Integrated Longitudinal and Lateral Control for High-Speed Platooning of Articulated Vehicles

cs.RO eess.SY ·2026-10-21 ·Aashish Shaju, Steve Southward, Mehdi Ahmadian
published similarity 0.48
Abstract · Original manuscript of an article published in Vehicle System Dynamics on September 20, 2026. Published version: https://doi.org/10.1080/004…

This paper presents an integrated control framework for high-speed platooning of articulated vehicles, combining advanced longitudinal and lateral control strategies to address the challenges of safe and efficient autonomous driving. A novel proof of string stability for the proposed longitudinal control algorithm, based on a PID framework, ensures robust inter-vehicle distance regulation even under dynamic operating conditions. Additionally, an arc-length-based longitudinal error formulation enhances the applicability of the control system for curved roads, making it realistic for diverse driving scenarios. For lateral control, significant improvements to the clothoid-based path tracking algorithm are introduced to mitigate oscillations and enhance stability at high speeds. These enhancements include a tangential criterion for oscillation reduction, trajectory segment classification for adaptive lookahead distance tuning, a dual-adaptive mechanism for regulating the rate of lookahead distance adjustments based on both cross-track error (CTE) and anticipated road curvature, and extensions for articulated vehicle dynamics. The proposed integrated control framework is validated through simulations, demonstrating its effectiveness in maintaining stability, minimizing tracking errors, and ensuring robust performance in high-speed and challenging platooning scenarios.

0.41

A Note on the Point-Clothoid Distance Algorithm

cs.CG math.NA ·2026-09-09 ·Haibin Ye, Hao Ge, Gong Cheng
theory similarity 0.47
Abstract

Computing the closest point on a clothoid is a recurring task in geometric design, road and railway alignment, and path planning. The efficient algorithm of Frego and Bertolazzi addresses this problem, but its candidate-selection analysis assumes at most one local minimum per search interval. We exhibit admissible configurations with two local minima, raising the question of whether the existing strategy accounts for every possible minimum. Using the geometry of the clothoid evolute, we prove that, for any query point and any proper no-inflection planar clothoid segment with tangent-angle variation at most $2π$, the squared-distance function has at most three stationary points; if all three are local extrema, their order is min-max-min. This establishes the completeness of the original candidate-selection logic beyond the one-minimum premise. It also shows that no interior search is needed when neither endpoint derivative test is active, allowing unnecessary midpoint searches to be omitted while retaining numerical fallback. Numerical experiments demonstrate reductions in iteration count and evaluation time.

0.25

High-Fidelity Multi-Body Simulator for Autonomous Racing

cs.RO eess.SY ·2026-09-11 ·Nicola Musiu, Francesco Iacovacci, Fausto Lupo, Matteo Pini, Giovanni Scapicchi +9 more
similarity 0.47
Abstract

We present a custom high-fidelity vehicle dynamics simulation environment for testing and validation of Autonomous Racing software. The digital twin of the autonomous vehicle is developed in Dymola, using racecar dynamics modeling libraries to build a complete multi-body model. A 3D road surface, including elevation profiles and curbs, is implemented using the Curved Regular Grid (CRG) standard. The model is exported from Dymola as a Functional Mock-up Unit (FMU) and integrated into a custom software-in-the-loop simulator, where communication interfaces with the autonomous racing stack were developed in C++. A calibration procedure based on experimental data is also presented, along with a validation study to further support the quality of the proposed framework. The simulator runs in real time on a portable computer and provides reliable ground truth for algorithms validation prior to real-world deployment.

0.20

Energy- and Time-Efficient Multi-Vehicle Trajectory Planning Using Augmented DAG Search in Configuration Space

eess.SY ·2026-11-10 ·Amirreza Akbari, Galina Sidorenko, Johan Thunberg
similarity 0.47
Abstract · This manuscript is currently under review at IEEE Transactions on Intelligent Transportation Systems

Multi-vehicle trajectory planning for CAV requires balancing energy consumption and travel time while ensuring safety and scalability. While travel-time-optimal methods based on Integer Programming exhibit poor scalability in large-scale multi-vehicle scenarios, existing energy-oriented approaches fail to balance energy consumption and travel time. We extend a configuration-space framework for multi-vehicle trajectory planning to jointly locally optimize travel time and energy consumption. A weighted energy-travel time objective is combined with an efficient augmented DAG search on two-dimensional decompositions of a high-dimensional configuration space, enabling scalable and collision-free coordination of large numbers of vehicles. Although the proposed framework is applicable to other traffic scenarios, such as roundabouts and vehicle-following, we focus on intersections as a representative and challenging planning problem. To further improve performance for our methodology, we also extend the method with an insertion-ordering heuristic that exploits reduced-space geometric information. Combined with nonlinear model predictive control, the proposed framework is shown to scale to 40 vehicles, outperform MILP-based and convex optimization baselines in dense intersections, and reduce energy consumption at equalized travel times relative to time-optimal planning.

0.23

Induced Riemannian Metrics for Motion Planning with Constraints

cs.RO ·2026-09-22 ·Phone Thiha Kyaw, Thomas Cohn, Miguel Angel Rogel Garcia, Jonathan Kelly
similarity 0.46
Abstract · 9 pages, 2 figures, 4 tables

In constrained motion planning problems, task and loop-closure constraints restrict a robot's motion to a curved, lower-dimensional submanifold of its configuration space. Planners measure path length with a metric, which sets the cost of moving in each direction. Under the Euclidean metric, this cost is the same everywhere, whereas under a general Riemannian metric, such as the kinetic-energy metric, the cost can vary with direction and configuration. Existing methods often describe the submanifold either implicitly, as a constraint level set, or explicitly, through a parameterization. The implicit representation is typically combined with the Euclidean metric of the configuration space, and the explicit representation with the parameter domain, so the path length that a planner minimizes depends on the representation. Instead, we measure path length with the induced metric, which the submanifold inherits from a Riemannian metric on the configuration space. The implicit and explicit representations yield the same induced metric, expressed in different coordinates, and hence the same geometry. This result holds for any Riemannian metric on the configuration space, not only the Euclidean one. The choice of metric is therefore independent of the choice of representation. Using this result, we extend planning under a Riemannian metric from unconstrained spaces to constraint submanifolds by applying the induced metric in both a sampling-based planner and a trajectory optimizer. For an explicit representation, the induced metric also accounts for the distortion that the parameterization introduces. In experiments on a bimanual manipulation setup with two Franka arms under end-effector task constraints, we compare the Euclidean and kinetic-energy metrics.

0.32

The Flat Earth Error: Differential Geometry in Vehicle Dynamics

eess.SY ·2026-08-25 ·David J. N. Limebeer, Charl van de Merwe
benchmark similarity 0.46
Abstract · 38 pages, 12 figures, 3 tables

The widespread idealization of road surfaces as horizontal planes can introduce significant inaccuracies into vehicle dynamics simulations, a phenomenon termed the ``Flat Earth Error.'' This article provides an expository guide to the use of classical differential geometry to model vehicular motion on curved surfaces. The influence of road curvature is characterized using the metric tensor, the second fundamental form, the shape operator, and the Christoffel symbols. Reproducible MATLAB scripts using an elliptic cone as a benchmark example illustrate the construction of geodesic curves and the simulation of particle dynamics on curved surfaces. The resulting geometric structures are integrated into a single-track vehicle-and-track model within a pseudospectral optimal control framework. Trajectory optimization results over a high-density mobile LiDAR profile of Darlington Raceway are used to generate a high-fidelity road-surface model. This model is used within an hp-adaptive collocation framework to investigate minimum lap time optimal control vehicular trajectories. These computations capture the non-smooth traction saturation limits of the tyres alongside position-dependent variations in gravitational forcing. Integrating differential geometry, multibody mechanics, and optimal control is essential for high-fidelity driven and autonomous vehicle-dynamics simulations. The optimized velocity and tyre slip profiles show that real-world racing track geometries induce dynamically significant three-dimensional effects. These results are particularly relevant to performance-limited simulations on highly banked track surfaces such as NASCAR ovals.

0.19