CS Paper Radar

Acoustic Signature Optimisation for Bioinspired Flapping-Wing Micro Aerial Vehicles

Yi Lun Duh, Krispin C. V. Broers, Sophie F. Armanini

cs.RO ·submitted 2026-10-27 13:12 UTC · v1

Abstract

Flapping-wing micro air vehicles are prized for quiet flight, yet the few existing measurements show engineered wings to be 15-30 dB louder than the animals they imitate. This paper investigates two passive geometric approaches to reduce the acoustic signature of a flapping membrane wing, and applies these to an exemplary wing. A significant sound source in flapping wings is the impulsive click radiated at stroke reversal, when a slack membrane snaps between two curvatures. Our first noise-reduction approach optimises the wing's venation layout, based on an analytical model of the reversal click as a dynamic snap-through of the membrane. The optimised venation pattern was manufactured and resulted in a reduction of up to 8 dB during the reversal snap in experiments. During testing, the venation was found to be sensitive to orientation rather than thickness. Secondly, an additive trailing-edge fringe inspired by hummingbird feathers was shown to further reduce the broadband swoosh by 3-4 dB at no lift cost, matching a cut serration wing without removing lifting area.

Comment
9 pages, 6 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Flap like a bat: Soft pneumatic wings for biomimetic ornithopters

cs.RO ·2026-10-31 ·Besetty Satyanarayana, Sirivelu Akhilesh, Bammidi Abhilash, Prabhat Kumar
similarity 0.55
Abstract · iNaCoMM2025 conference paper

This paper describes the development of a bio-inspired ornithopter wing mechanism that uses soft pneumatic actuators, such as PneuNet structures, in place of revolute joints, inspired by the complicated kinematics of bat flight. The proposed design employs pneumatically driven air pockets within a flexible wing skeleton to achieve smooth, lifelike flapping motion. The actuation system is controlled by 3/2-way solenoid valves and an air pump, which manipulate airflow and actuator deformation. We demonstrate, using ANSYS FEA software, the bending behavior of the PneuNet actuators under varying pressures to inform the wing's structural design. The implementation of soft robotics in the flapping-wing system offers potential advantages over traditional mechanisms, such as reduced mechanical complexity, lower acoustic signatures, enhanced adaptability, and wing morphing. This work demonstrates the feasibility of replacing rigid revolute joints with compliant pneumatic actuators, enabling more agile, silent, and biomimetic aerial robots.

0.32

Self-excited actuation enables adaptive and resilient flapping-wing flight

cs.RO ·2026-09-16 ·Rundong Yang, Ethan S. Wold, Ellen Liu, James Lynch, Wei Zhou +3 more
similarity 0.55
Abstract

The muscles that power insect flight fall into one of two categories: 1) synchronous muscles that contract under direct control from the nervous system, and 2) asynchronous muscles which have an intrinsic stretch activation response that spontaneously generates wingbeats without the need for signaling from the brain. It is thought that the emergent nature of asynchronous wingbeats provides both adaptive and responsive capabilities for flight control. To date, most flying robots use synchronous actuation. In this paper we develop the first flight-capable flapping wing robot that uses asynchronous actuation. We demonstrate that asynchronous actuation allows wings to respond to changes in the resonant mechanics of the body without control input, and wings can react instantaneously to collisions with obstacles with no extrinsic sensing needed. Flight tests within cluttered environments demonstrate that asynchronous actuation significantly improves stability and performance when compared to synchronous actuation. In total this work demonstrates that a flapping wing robot actuation strategy that emulates the asynchronous muscles of flying insects can provide fast, reactive actuation responses before a control system would need to intervene. This partitioning of embodied control to both the low-level actuation dynamics and and high-level sensorimotor system provides a compelling blueprint for new flying robots.

0.23

Optimized size, shape and orientation of rhombic transposition flaps and excisions by gradient-based methods

cs.CE physics.med-ph ·2026-11-03 ·Niels Aage, Brandon Marshal Parks
unusual similarity 0.48
Abstract · 21 pages, 9 figures, 4 tables. Submitted to the Journal of the Mechanical Behavior of Biomedical Materials

This work presents a new method for gradient-based optimization of the rhombic transposition flap and the excision it closes, which set the strain of the skin after closure. Previous studies swept at most three parameters. Here, using structural optimization methods, up to eight variables, two flap angles, two cut lengths and the size, shape and position of the rhombic excision, are optimized under up to 32 geometric and stress constraints. The skin is a pre-stretched, incompressible hyperelastic membrane that wrinkles instead of carrying compression. Smoothed level-sets on a fixed grid represent the cuts, and springs between interpolated points the sutures, so designs change without remeshing and the adjoint method gives the sensitivities. The energy the surgery adds to the skin is minimized, and the model reproduces the energies of a published 48-design sweep with a median deviation of 5%. The optimal flap angles, $(-23^\circ, 31^\circ)$, lie outside the swept range and add 63% less energy than the Limberg flap and 15% less than the best swept design. Under unequal in-vivo tension, the optimal flap turns with the direction of the tension. Fitting the excision to the lesion and its margin lowers the energy by a further 35%, and with all eight variables it is 78% below the Limberg flap. This optimum is the same for finer grids, narrower cuts and wider undermining, although wider undermining reduces its gain. Lowering its suture-line stress by 41% costs only 2.3% more energy.

0.32

Towards insect-like distributed proprioception in actuators and appendages for flapping-wing insect-scale aerial robots

cs.RO ·2026-08-22 ·Alexander Hedrick, Arvind Gupta, Kaushik Jayaram
similarity 0.48
Abstract · 8 pages, 6 figures, this work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after wh…

Modern flapping-wing insect-scale air vehicles display agility similar to that of their insect counterparts; however, these impressive maneuvers are only possible with off-board sensors like optical tracking cameras. In this manuscript, we introduce two embedded proprioceptive sensors for insect-scale aerial robots: thin film piezoelectric polymers integrated directly into a driving actuator and a pitching hinge which track stroke and pitch angle, respectively. We fabricate the aforementioned size-agnostic mechanically intelligent structures (sensor-actuator, sensor-flexure) using laminate stack fabrication methods. Chirp experiments with our sensors integrated into an insect-size flapping-wing robot show accurate tracking of stroke (RMSE = 0.44 deg) and pitch (RMSE = 2.44 deg) angles in the relevant frequency range. As the first step towards demonstrating the utility of these sensors for enabling numerous onboard autonomy applications, including closed-loop wingbeat control and sensor fusion with existing insect-scale sensor suites for more accurate proprioception and localization, we show one application for each sensor. The proprioceptive hinge enables collision detection, reducing the chance of permanent damage if the robot's wing collides with an object. The proprioceptive actuator enables asynchronous flapping, which is hypothesized to increase adaptability and efficiency in insects and robots alike. A microrobot equipped with our proprioceptive actuator allows us to test these hypotheses with potential for improving flapping aerial robot performance. We foresee proprioceptive sensors having an important role in progressing both the fields of insect-scale aerial robots and robo-physics due to the bio-inspired nature and high integration level of our sensors.

0.27

Rigid-body support motion and post-flutter piezoelectric energy harvesting from a pitch-plunge-flap aerofoil

cs.CE ·2026-09-21 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
similarity 0.48
Abstract

A piezoelectric transducer on a pitch-plunge aerofoil with a finite-mass trailing-edge flap turns the limit cycle that follows flutter into electrical power. The design findings for such a harvester have so far been obtained with the section's suspension reacting against rigid ground, which is what a wind-tunnel mounting provides. Here a 3-dof aerofoil with a transducer is carried by a fuselage mass that is itself free to translate, so that the coupled system is free-free and the wing's plunge is measured relative to a support that moves. The support degree of freedom is destabilising on its own, softening the flutter mode by taking a share of it in antiphase with the wing's plunge, and it acts on the three transducer mountings unequally, amplifying the plunge mounting's destabilisation, leaving the largest pitch-mounted stabilisation untouched while halving it where the electrical time constant meets the flutter frequency, and leaving the flap mounting alone. The optimum coupling and load resistance do not move, so the matching rules of the rigidly supported section carry over unchanged. The harvested power rises with the support mass at a fixed flow speed for every mounting, and that rise is shown to be an artefact of the fixed-speed convention rather than a property of the cycle. Measured instead at a fixed margin above each system's own flutter boundary, which divides out the boundary's motion, the plunge mounting keeps a real gain while the pitch mounting loses power, so the apparent benefit of a soft support to a pitch-mounted harvester is entirely the boundary coming down to meet the flow speed. A harvester result quoted at a fixed speed and read as a property of the limit cycle is therefore wrong by the whole of that difference.

0.38

FlapKAD: A Simulation Dataset of Coupled Wing Kinematics and Aerodynamic Dynamics for Flapping-Wing Aerial Vehicles

cs.RO ·2026-09-30 ·Haichuan Li
benchmark similarity 0.47
Abstract

Experimental investigation and modeling of flapping-wing aerial vehicles are limited by the scarcity of large-scale records that temporally align wing kinematics, aerodynamic responses, and flight states. Existing datasets are often limited in scale and affected by measurement noise and temporal misalignment between rapidly varying wing motion and the associated dynamic response, particularly during high-frequency flapping. We introduce FlapKAD, an episode-structured simulation dataset comprising 2,000 rigid-wing flight episodes and 720,152 valid time steps, with bilateral wing kinematics, aerodynamic responses, and flight states recorded synchronously within a common clock. FlapKAD supports a unified bidirectional sequence-prediction benchmark constructed from the same temporally aligned episodes. The forward task predicts future vertical force coefficients and body vertical velocity from histories of realized flap and twist angles, whereas the inverse task reconstructs future flap- and twist-angle trajectories from the corresponding response histories. A benchmark of eight representative time-series architectures across multiple prediction horizons reveals direction- and horizon-dependent model behavior, systematically higher reconstruction errors for twist angle than for flap angle, and no consistent advantage from increased architectural complexity. FlapKAD provides a reproducible dataset and benchmark for studying coupled wing-kinematic, aerodynamic, and flight-state dynamics in flapping-wing aerial vehicles.

0.27

From Model to Prototype: Design and Motor-Flap Propulsion Control of a Twin-Wing Metamorphic UAV

cs.RO ·2026-10-06 ·Anja Bosak, Dorian Erić, Ana Milas, Stjepan Bogdan
similarity 0.45
Abstract · 8 pages, 12 figures

This paper presents the design and control strategy for MetaMorpher, a metamorphic Unmanned Aerial Vehicle (UAV), capable of both spinning-wing hover and fixed flying-wing cruise flight. Since control of the cruise configuration is comparatively well established in the literature, this paper focuses on control of the MetaMorpher in hover mode, building on the flight dynamics model and conceptual design validated in previous work. The control algorithm is implemented using one of two phase-synchronized strategies: motor propulsion, which pulses motor thrust in synchrony with the vehicle's rotation, or flap propulsion, a novel strategy that pulses the deflection of the wing-mounted elevons. We evaluate both strategies in simulation through different flight experiments. Simulation results confirm the mathematical model and show stable reference tracking, demonstrating flap propulsion as a lightweight, decoupled alternative for hover control. Experimental testing validated the vertical-dynamics propulsion model against the physical prototype, demonstrating very good steady-state agreement across different configurations.

0.22

Transducer Placement and the Limits of a Four-State Reduced Model in Post-Flutter Piezoelectric Energy Harvesting from a Pitch-Plunge-Flap Aerofoil

cs.CE eess.SYmath-ph ·2026-09-11 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
unusualhighly cited similarity 0.44
Abstract · 16 pages; 6 figures;

Aeroelastic ?utter is normally a failure mode to be designed against, yet the limit-cycle oscillations (LCOs) that follow it convert flow energy into sustained structural motion that a piezoelectric transducer can turn into electrical power. A transducer is embedded in a three-degree-of-freedom pitch-plunge aerofoil with a finite-mass trailing-edge flap and unsteady strip-theory aerodynamics, giving a fifteen-state electro-aeroelastic system with a cubic hardening pitch spring, and the system is reduced by biorthonormal projection of the Taylor-expanded residual onto eigenvectors of the coupled Jacobian. The testbed is deliberately low order, so that every reduced prediction can be checked against the full-order system it replaces. The degree of freedom that carries the transducer is a first-order design variable, since it sets both the sign of the shift in the flutter boundary and the magnitude of the harvested power. The error of the reduced model is dominated not by the size of the retained basis but by how the reduced operator is made to depend on low speed. Expanding the retained eigenvalues leaves the reduced operator block-diagonal, with no coupling between the retained modes at any order of the expansion, whereas re-projecting the exact Jacobian onto the same frozen basis supplies that coupling and restores the structural response without enlarging the basis. It is found that the error that remains lies in the harvested voltage, which the equilibrium eigenvectors carry in a fixed proportion to the motion, and this is not removed by adding the electrical modes to the basis, whereas the flap detection, which the same basis also misses, is recovered by retaining the flap modes. The accuracy of a harvester reduced-order model must therefore be reported on the harvested quantity itself.

0.57