CS Paper Radar

Optimized size, shape and orientation of rhombic transposition flaps and excisions by gradient-based methods

Niels Aage, Brandon Marshal Parks

cs.CE physics.med-ph ·submitted 2026-11-03 09:27 UTC · v1
unusual

Abstract

This work presents a new method for gradient-based optimization of the rhombic transposition flap and the excision it closes, which set the strain of the skin after closure. Previous studies swept at most three parameters. Here, using structural optimization methods, up to eight variables, two flap angles, two cut lengths and the size, shape and position of the rhombic excision, are optimized under up to 32 geometric and stress constraints. The skin is a pre-stretched, incompressible hyperelastic membrane that wrinkles instead of carrying compression. Smoothed level-sets on a fixed grid represent the cuts, and springs between interpolated points the sutures, so designs change without remeshing and the adjoint method gives the sensitivities. The energy the surgery adds to the skin is minimized, and the model reproduces the energies of a published 48-design sweep with a median deviation of 5%. The optimal flap angles, $(-23^\circ, 31^\circ)$, lie outside the swept range and add 63% less energy than the Limberg flap and 15% less than the best swept design. Under unequal in-vivo tension, the optimal flap turns with the direction of the tension. Fitting the excision to the lesion and its margin lowers the energy by a further 35%, and with all eight variables it is 78% below the Limberg flap. This optimum is the same for finer grids, narrower cuts and wider undermining, although wider undermining reduces its gain. Lowering its suture-line stress by 41% costs only 2.3% more energy.

Comment
21 pages, 9 figures, 4 tables. Submitted to the Journal of the Mechanical Behavior of Biomedical Materials

Closest papers

Nearest neighbours by meaning across the whole index.

Physically Interpretable Basin Selection in Discrete-Variable Origami Design

cs.LG cond-mat.mtrl-scicond-mat.soft ·2026-11-12 ·Lucy Liu, Leon M. Kamp, Katia Bertoldi, L. Mahadevan
similarity 0.52
Abstract

Automatic differentiation has enabled rapid progress on continuous-variable mechanical design problems, but gradient-based optimization still struggles with discrete variables. The standard approach is to optimize using a continuous relaxation of the choices, then commit to the nearest discrete design at the end. Why this procedure selects unfavorable basins is poorly understood. Here, we introduce a practical, interpretable design problem inspired by origami, in which automatic differentiation is used to design shapes with a target functional behavior. Each origami sheet has a fixed geometry, and a bilevel optimization framework tunes which one of four discrete hinge types to place at each fold. Baseline gradient-based design settles into basins with a large discretization gap: relaxed optimization solves 97% of runs, but the final, discrete solutions succeed only half the time. We find that the gap can be relieved with a surprisingly simple modification. An initialization prior uniformly biased toward the stiff, flat hinge option boosts the final solve fraction from 49% to 69%. Applying the prior adds no additional compute and leaves the optimization process unchanged. Compared to the baseline, sheets produced with the prior have greater geometric compatibility and mechanical stiffness. Directly penalizing frustration and floppiness in the outer loss function produces an even greater improvement than the prior does, raising the solve fraction to 78% and indicating that these properties help distinguish the unfavorable basins. Our results demonstrate that loss landscapes for mechanical design can have physically meaningful basins that are not robust to discretization and cause solves to fail. Targeting these basins' physical signatures, even with just an initialization bias, helps avoid them.

0.30

Concurrent two-scale topology optimization of printable bone scaffolds via rectified-flow generation and exact latent-space refinement

cs.LG physics.comp-ph ·2026-10-18 ·Reza T Batley, Sourav Saha
benchmarkunusual similarity 0.51
Abstract

Bone scaffolds must reconcile a macroscale mechanical response with microscale geometric feasibility, yet conventional approaches to their design restrict attainable constitutive properties. This work presents a concurrent two-scale topology optimization framework; a conditional rectified flow generates periodic lattice microstructures, which are then refined in latent space by exact finite-element homogenization sensitivities. The resulting unit-cell geometries and their spatial assignments are jointly optimized under mechanical and feature-size constraints. In a distal rabbit femur benchmark, all eight flow-started refinements produce printable cells with maximum relative errors under 1\% across six prescribed engineering moduli. Constructing the implant from a single tiled cell reproduces intact whole-femur compliance within 0.1\% and regional strain energy within 0.35\% under four loading conditions. In human femoral reconstruction, multiscale concurrent optimization produces a cortical mid-shaft scaffold with porosity 63\% while satisfying the compliance constraint within 2\% under walking and stair-climbing loads. It achieves an 84\% porosity on a proximal cancellous scaffold with strain-energy deviations below 0.25\% under the same loads. Analysis of the learned representations reveals distinct architectural families in latent space. Further, the attention heads of the rectified-flow transformer specialize for spatial shifts -- learning the analogue of a finite-difference stencil -- and coordinate symmetries, with ablations showing their influence on generated topologies. These results establish a route to printable, mechanically constrained scaffold designs. The framework is general enough for extending to many other multiscale structural design applications including topology-microstructure co-design in metal additive manufacturing.

0.22

Structural Affinity: An Algorithm for Coherent Cage-Based Shape Design

cs.LG cs.GRcs.RO ·2026-10-16 ·Aviraj Newatia, Shengan Yang, Hantao Zhong, Rika Antonova
similarity 0.51
Abstract · 27 pages, 16 figures

Cage-based deformation (CBD) parametrises 3D geometry through a small set of control handles, effectively enabling a variety of tasks from animation and interactive modelling to tool-based co-design, neural deformation transfer, and aerodynamic shape optimization. Many optimization approaches relying on CBD employ regularisation strategies to reduce the distortion of the deformed mesh by encouraging smooth, regular cage deformations. These techniques offer soft guidance to an optimization algorithm towards desirable deformations, but compete with the task objective rather than changing the deformation parameterization itself. In this work we introduce Structural Affinity for CBD, an explicit regularisation method which enables smooth deformations through control cages by exploiting a two-cage structure to couple cage-handle motion directly. Structural Affinity precomputes an affinity matrix using mean-value coordinates, binding the inner control-cage to a coarser outer-cage. This matrix defines how much a cage handle displacement propagates to neighbouring handles which substantially decreases and often eliminates cage self-intersections, reduces mesh distortion, and adds linear overhead at deformation time. Across robotic control--morphology co-design, source-to-target neural deformation transfer, and aerodynamic wing shape optimization, Structural Affinity produces more regular deformations and substantially reduces reliance on hand-designed structural loss terms. We report consistent gains on three complementary diagnostics: the cotangent Laplacian, a proxy for surface smoothness; cage distortion, capturing whether control handles move coherently; and surface roughness, which measures undesirable oscillation in wing geometry.

0.24

Shape optimisation of nonlinear Naghdi shells on discrete geometries

cs.CE math.NA ·2026-08-11 ·Ado Farsi, Alberto Paganini
benchmark similarity 0.51
Abstract · 19 pages, 10 figures, 6 tables. Revised manuscript submitted to Computers & Structures

We present an automated framework for the shape optimisation of a geometrically nonlinear, five-parameter Naghdi model on faceted triangulations. By recovering directors numerically, we remove the requirement for an analytic or spline parameterisation of the mid-surface, whereas partial selective reduced integration alleviates locking. The residual and tangent of symbolic energies are generated in an automated fashion building on Firedrake's and UFL's symbolic differentiation capabilities. Additionally, UFL's and pyadjoint's algorithmic differentiation enables automated first and second shape derivative evaluations that are verifiably correct via Taylor tests. The forward model agrees with the Sze/Abaqus semi-cylinder reference. A three-model mesh-refinement study indicates that geometry recovery and surface faceting have small effects on the predicted deflection. Numerical experiments show that 100 trust-region iterations suffice to reduce the squared-displacement functional of a semi-cylinder by 98.4% and the elastic strain energy of a bracket by 94.6%. The latter result is validated against a COMSOL benchmark. Non-uniqueness of optimal shapes is demonstrated by optimising initial designs subject to small perturbations. Comparisons with linearised designs distinguish optimisation performance from the accuracy of the predicted nonlinear response.

0.12

Inverse origami inspired by insect morphogenesis: geometric design of wrinkle structures for curved surface formation

cs.GR cond-mat.softphysics.app-phphysics.bio-ph ·2026-10-26 ·Kentaro Morikawa, Yuuki Shimizu, Nen Saito, Yasuhiro Inoue
unusual similarity 0.50
Abstract · 10 pages, 7 figures; SI Appendix: 4 pages

Insect exoskeletons abruptly acquire complex three-dimensional forms during metamorphosis from larva to pupa. This transformation occurs through the unfolding of preformed wrinkle structures inside the larval body under internal pressure. Inspired by this process, we investigate an inverse-origami strategy for fabricating curved surfaces. Whereas conventional origami produces three-dimensional objects by folding a flat sheet, this strategy produces curved surfaces by unfolding preformed wrinkle structures. The central design problem is to derive a wrinkle structure from a prescribed target surface. Our key idea is to regard a wrinkle structure as a unidirectional stretching field, which specifies at each point the stretch produced when the structure unfolds. We first derive such a field from the target surface geometry and then translate it into spatially varying wrinkle directions and spacing, so that the wrinkle structure unfolds into the target. The resulting numerical designs approximate the intrinsic metric of the target surface. We demonstrate the method on multiple target surfaces through numerical construction, mechanical unfolding simulations, and 3D-printed prototypes. This work provides a biologically inspired geometric design principle for encoding prescribed surface shapes in wrinkle structures, as well as a framework for designing and fabricating deployable curved surfaces.

0.35

Acoustic Signature Optimisation for Bioinspired Flapping-Wing Micro Aerial Vehicles

cs.RO ·2026-10-27 ·Yi Lun Duh, Krispin C. V. Broers, Sophie F. Armanini
similarity 0.48
Abstract · 9 pages, 6 figures

Flapping-wing micro air vehicles are prized for quiet flight, yet the few existing measurements show engineered wings to be 15-30 dB louder than the animals they imitate. This paper investigates two passive geometric approaches to reduce the acoustic signature of a flapping membrane wing, and applies these to an exemplary wing. A significant sound source in flapping wings is the impulsive click radiated at stroke reversal, when a slack membrane snaps between two curvatures. Our first noise-reduction approach optimises the wing's venation layout, based on an analytical model of the reversal click as a dynamic snap-through of the membrane. The optimised venation pattern was manufactured and resulted in a reduction of up to 8 dB during the reversal snap in experiments. During testing, the venation was found to be sensitive to orientation rather than thickness. Secondly, an additive trailing-edge fringe inspired by hummingbird feathers was shown to further reduce the broadband swoosh by 3-4 dB at no lift cost, matching a cut serration wing without removing lifting area.

0.33

Love Handles: Decimation for Deformation Handles with Compact Support and Low Memory Footprints

cs.GR ·2026-08-18 ·David IW Levin, Paul Kry, Kartic Subr, Ryan Schmidt, Etienne Vouga +1 more
similarity 0.48
Abstract

Estimating the deformation of solids via physical simulation is an important problem spanning fields such as computer animation, engineering and robotics. Such simulations are computationally expensive and scale poorly when the representation of an object is refined by increasing the level of discretization. Reduced Order Methods (ROM) offer computational savings by decreasing the number of degrees of freedom, for example by using \emph{handles} that control groups of vertices. We present the first decimation-based algorithm for computing a sparse, compactly supported set of deformation handles. The crux of our method utilizes iterative algebraic simplification to optimize handle deformation to match any input deformation, such as linear vibration modes. This applies to any volumetric input mesh, including those with high genus or porous features, since we do not alter the geometry. We also devise an efficient algorithm to compute and update compact supports and their associated weights. We leverage compact support to develop an efficient, reduced-cubature computation scheme. Once optimized, our handles offer a memory-efficient solution while enabling real-time elastodynamics simulation of complex geometry. We show real-time performance on a variety of tetrahedral meshes with up to 796,623 tetrahedra.

0.23

CROPS: Cosserat-Rod-Based Co-Design of Soft Slender Programmable Material Systems for Biomedical Applications

cs.CE cs.RO ·2026-10-16 ·Aaditya Chandrasekhar, Dex Doksoo Lee, Hyunwoo Kwon, Shicheng Li, Wei Chen
similarity 0.47
Abstract · Submitted to Finite Elements in Analysis and Design

Slender structures made of stimuli-responsive materials represent an emerging class of programmable material systems, with applications in soft robotics, minimally invasive surgery, wearable electronics, and deployable structures. In biomedical applications, the on-demand design of slender structures, encompassing both their material layout and actuation, is essential to harnessing their large deformation and multiphysics actuation to meet patient-specific design requirements. However, owing to geometric and material nonlinearities, their structure-actuation-response relationship is highly nonintuitive and computationally demanding. This often makes trial-and-error and conventional design approaches challenging for addressing patient-specific needs. To this end, we present a Cosserat-rod-based design optimization framework for the autonomous design of programmable slender structures. Leveraging the Cosserat rod representation, the end-to-end differentiable framework is demonstrated on two case studies: (i) design of swellable stents that morph to the shape of carotid vessels; (ii) co-design of the remnant magnetization and the applied field of magnetically-active catheters to reduce the force exerted on the patient-specific vessel wall during insertion. Both self-contact and external contact with surrounding structures are accounted for. We consider two actuation mechanism, namely the swelling of gel-elastomer composites and the magnetic actuation of hard-magnetic composites. The proposed framework presents an autonomous design platform of soft slender material systems that support large deformations and multiphysics actuation toward personalized biomedical design.

0.25