CS Paper Radar

Locating Contact on Tendon-Driven Continuum Robots From Tendon Measurements Alone via Constrained Moving Horizon Estimation

Haitham El-Hussieny

cs.RO ·submitted 2026-11-06 18:53 UTC · v1
benchmarktheory

Abstract

Tendon-driven continuum robots can reach through constrained spaces, but contact along their bodies is invisible to the sensors at their motors. We show that this is a structural limitation rather than a tuning problem: the map from contact forces to tendon measurements has a null space of dimension at least seven, so no estimator that leaves the contact support free can locate contact. When the obstacle geometry is known, however, non-penetration and complementarity make the contact force locally identifiable, and we prove that the resulting system with unknown contact inputs is locally exponentially strongly detectable. We present a constrained moving horizon estimator (MHE) that encodes these conditions and runs in real time as one quadratic program per sample, and we give a local, mode-wise robust stability result for it. In a finite- element benchmark of a two-section robot pressing and sliding on a wall, the estimator located contact to 0.9 mm and estimated contact force to 0.22 N, compared with 65 mm and 0.72 N for a tuned extended Kalman filter (EKF) with state projection. The estimator tolerated millimeter- level errors in the obstacle position and unmodeled wall friction, under which the projected EKF failed. Under randomized model mismatch over 40 trials, including unmodeled tendon friction, it remained better in force and location in every trial. Without contact, the MHE offered no advantage over the EKF, which confirms that its benefit comes from the contact constraints. This report extends a letter submitted to IEEE Control Systems Letters with complete proofs and additional experiments.

Closest papers

Nearest neighbours by meaning across the whole index.

Force/Torque-Based Kinematic Adaptation for Robotic Manipulation Tasks

cs.RO ·2026-08-21 ·Carl Glen Henshaw
hot direction similarity 0.60
Abstract · 29 pages including appendices, 3 figures

Contact-rich robotic manipulation requires an accurate model of the kinematic relationship between a robot's joints and the task features it senses. This relationship is rarely known exactly: it changes with each tool the robot picks up and shifts, sometimes almost instantaneously, as contact modes change --- especially for multi-fingered hands that make and break contact at points that are not exactly prescribed, as in full-hand grasping. This paper develops an adaptive scheme that estimates that relationship online, using only joint-angle sensing and a wrist-mounted force/torque sensor, with no exteroceptive measurement of the tool tip. We derive a provably stable kinematic update law that identifies the kinematics of an unknown tool from force/torque feedback alone, and prove stability of both the rigid case and the case with a compliance controller as an inner loop. We show that identification is confined to the directions the motion excites --- so that, for example, a tool's length is unobservable under a rigid insertion push, while a compliant loop's passive yielding partially excites it; and that with a second-order admittance the compliant certificate holds unconditionally in continuous time. We also pose the combined control and estimation problem as a Quadratic Program (QP): the formulation yields the prediction term of the update law exactly but, instructively, cannot reproduce the tracking adaptation term. We validate the scheme in simulation on a peg-in-hole insertion. This work is the first step in a research program aimed at factoring manipulation learning into a task policy which can be learned in isolation of the robot, for instance by reinforcement learning, and an adaptive kinematic component that adapts online to the particular robot, hand, or tool in use.

0.29

Bayesian Continuum Robot Dynamics and State Estimation

cs.RO ·2026-09-17 ·James M. Ferguson, Tucker Hermans, Alan Kuntz
similarity 0.60
Abstract · ICRA 2027 preprint

Recent factor graph approaches to continuum robot state estimation have been successful for quasi-static applications and spatiotemporal estimation using white-noise kinematic motion priors. However, when inertial effects are significant, these approximations may fail to capture the underlying physics, limiting accuracy during dynamic motions. In contrast, our approach approximates the Cosserat rod dynamics of continuum robots. We write inertia and damping as equivalent applied loads, so that the dynamic balance retains the algebraic form of the static one from prior work with quasi-static robots. Without backbone observations, the framework reduces to a stochastic forward simulation of the robot's motion. Given observations, it jointly refines kinematic and dynamic states and infers external loads, among other states. We validate the approach through simulation and experiments, demonstrating stochastic forward simulation as well as state estimation on tendon-driven continuum robots.

0.20

Magnetic based In-situ Self 3D Pose Estimation for a Modular Soft Tendon-Driven Continuum Robot via IMU-Fusion

cs.RO eess.SPeess.SY ·2026-09-30 ·Zheng Cao, Guo Ning Sue, Xiangyun Bu, David Quinn, Junzhe Hu +1 more
similarity 0.60
Abstract

Continuum robots are well suited for gentle manipulation because of their inherent compliance and ability to adapt to complex environments. However, their continuously deformable structure makes accurate configuration estimation challenging, particularly when external vision systems are unavailable or obstructed. In this work, we present an embedded pose sensing framework that combines inertial measurement units (IMUs) and active magnetic fields to estimate the robot configuration without relying on external cameras. The angular measurements from the IMU and magnetic-field references are fused to improve local orientation estimation and reduce accumulated orientation error during operation. This pose sensing scheme achieves an update rate of 16.7~Hz, allowing real-time feedback. The proposed system is experimentally validated through closed-loop control, where the estimated robot configuration is used to maintain the end-effector at a desired position while interacting with an object. These results demonstrate the potential of distributed magnetic--inertial sensing for real-time pose estimation and closed-loop control of continuum robots.

0.11

Actuation and Control of Passive Tendon-Driven Soft Extensions Through Rigid Manipulator Motion

cs.RO ·2026-11-11 ·Ignacio Cuiral-Zueco, Gonzalo López-Nicolás, Youcef Mezouar
theorycode/data similarity 0.59
Abstract · 16 pages, 12 figures. Soon to be submitted to the IEEE Transactions on Robotics. Code: https://github.com/nachocz/passive_soft_extension_con…

Industrial manipulators offer reach and precision but can damage nearby structures in confined spaces. Soft robots provide compliant contact but typically have limited reach. Rigid-soft systems combine their advantages, although they often require dedicated actuation and control hardware. We propose actuating a passive tendon-driven soft extension through manipulator joint motion. As the robot moves, the exterior spans of tendons anchored to upstream links change, altering tendon tension and deforming the extension. Inspection through narrow apertures, for example, constrains the motion of the end effector (EE). We develop a controller that regulates the soft tip while preserving such EE constraints. A differential model separates rigid transport from soft deformation, combining analytic arm and tendon kinematics with a locally identified span-to-deformation map. We also derive a local upper bound on the number of independent deformation directions transmitted by the tendons under the EE constraint, and conditions for the exponential convergence of the tip error. A quadratic program with control barrier functions imposes obstacle clearance, fulcrum limits, and model-validity conditions. Simulations and real experiments show tip and shape regulation under free, position-constrained, and fulcrum-constrained EE motion.

0.54

Real-Time Whole-Body Safe Motion Generation for Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-22 ·Fangju Yang, Siyi Ma, Tonghao Guan, Tingcong Liu, Hang Yang +3 more
hot direction similarity 0.59
Abstract

Real-time motion generation for tendon-driven continuum robots requires accurate modeling of nonuniform bending and whole-body collision avoidance. This paper presents a unified actuation-space framework for planar multi-segment tendon-driven continuum robots. An energy-based variable-curvature model captures spatially varying tendon spacing and bending stiffness and provides analytical Jacobians for differential inverse kinematics and safety monitoring. A multipoint CBF-QP enforces backbone clearance under obstacle motion and actuation-velocity bounds, while its decision dimension depends only on the number of independently actuated segments. The model closely agrees with GVS references, with a maximum curvature error of $5.223 \times 10^{-2}\,\mathrm{m}^{-1}$. Over 100 MuJoCo trials, the proposed method achieves collision-free success rates of 96% and 100% in static and dynamic scenarios, respectively, compared with approximately 60% and 80% without CBF constraints. Hole-traversal tests further demonstrate safe motion in constrained environments. With 600 backbone monitoring points, the mean control-step time is 6.66 ms, demonstrating real-time whole-body safe motion generation.

0.29

Tactile Reconstruction of Contact Task Frames and Forces for Hybrid Force/Motion Control

cs.RO ·2026-10-07 ·Antonio Rapuano, Simone Orelli, Barbara Bazzana, Antonio Franchi, Alessandro De Luca
similarity 0.59
Abstract · 14 pages, 9 figures, 7 tables. Video: https://youtube.com/playlist?list=PLejKMZmW8AvI. Dataset: https://doi.org/10.5281/zenodo.23209032

Hybrid force/motion control requires knowledge of the interaction force and of a task frame defining the force- and motion-controlled directions. These quantities are usually obtained from force/torque sensing or model-based residuals, often assuming also a nominal environment model. This work addresses the online estimation of the contact force and a possibly time-varying task frame using only soft optical tactile sensing, under the assumption of locally planar contact with a negligible contact moment. The proposed method maps a single image of the deformed elastomer of a soft optical tactile sensor to observable contact variables: indentation depth, two surface-to-sensor tilt angles, and 3D contact force, each with a per-sample uncertainty estimate. The mapping is learned through a self-labeling acquisition procedure, in which a manipulator imposes controlled contacts while an auxiliary Force/Torque sensor is used offline to provide ground-truth labels. The tactile measurement is then fused with robot proprioceptive data in an Extended Kalman Filter, producing a continuously updated estimate of the contact task frame and of the interaction force. Control experiments with a DigiTac sensor mounted on a UR10 manipulator demonstrate closed-loop contact force regulation against a flat rigid board in linear and angular motion by a human operator, with touch as the only exteroceptive feedback.

0.23

SCRUB: Contact-Based Surface-Frame Estimation for Force-Motion Control with an Armless Quadruped

cs.RO ·2026-11-04 ·Sourav Selvaraj, Juan Pablo Espinosa Chessal, Mahdi Agheli
similarity 0.58
Abstract · 8 pages, 6 figures, 4 tables

Wiping, sanding, and inspection robots press a sliding tool on a surface with controlled force. Controlling that force needs the surface normal, which is unknown on real-world, unmapped surfaces. Surface-normal estimators can help estimate the surface normal, but they either need a friction model or assume that the instantaneous tool velocity lies along the surface; however, walking violates this assumption. We propose SCRUB, a contact-based surface-frame estimator, which lets an armless quadruped slide a body-mounted tool along near-vertical surfaces in the absence of known, axis-aligned, or vision-predicted normals. SCRUB's predictive controller presses and slides the tool using a Kalman-filter estimate of the normal from two cues: 1) A force cue measures the estimate's tilt across the motion. If friction directly opposes the motion, the cue is zero exactly when that tilt is zero, for any friction coefficient. However, if the cue's sliding direction is wrong, friction appears as a false tilt. 2) A velocity cue measures tilt along the motion. Walking and pressing move the tool in and out. SCRUB therefore subtracts the commanded press rate from the tool velocity, averages the result over each gait cycle, and treats this mean as lying along the surface. On Unitree Go1 hardware at nominal speed and load, SCRUB completed every wall traverse and column orbit. No orbit completed with either cue removed, without gait averaging, or with a fixed normal.

0.21

CoPRE: Improving Sensitivity in Proprioceptive Contact Detection for Low-Cost Robot Arms

cs.RO ·2026-09-23 ·Yuxiao Zhu, Jinzhou Li, Yifei Dong, Muhammad Suhail, Chunyuan Yang +4 more
similarity 0.58
Abstract

Contact detection during robotic manipulation allows robots to recognize unexpected contact and adapt their motion accordingly. However, in low-cost robot arms without dedicated force or tactile sensors, detecting weak contacts from proprioception is challenging because the resulting changes in joint-level proprioceptive signals can be small compared to normal variation and noise caused by robot motion itself. We introduce Contact-free Proprioceptive Response Estimation (CoPRE), improving proprioceptive contact detection sensitivity using only contact-free motion, without additional force sensors, contact labels, or analytical dynamics models. CoPRE estimate the expected joint torques under contact-free motion from proprioceptive state history and commanded motion, while removing recent observations that may already reflect contact. It then computes the residual between the expected and observed joint torque estimates, and maps this residual to a contact score using a noise-weighted Jacobian. Real-robot experiments on ARX Arm and Unitree G1 show that CoPRE achieves 74.1% and 82.2% recall on the tested contact trials, compared with 0%/0% on ARX and 16.3%/42.2% on G1 for the learned torque-prediction and inverse-dynamics baselines. CoPRE also reaches 90% detection rate for pushing force at 3.5 N on ARX and 5.5 N on G1. To demonstrate the downstream utility of our method, we implement belief-space manipulation planning for obstacle-aware object placement and book insertion where detected contacts update the spatial belief and enable the robot to retreat from blocked motions, adjust its pose, and retry. Project website at https://copre-arm.github.io

0.35