CS Paper Radar

Fastener-centric acquisition and AND/OR graph representation of state-dependent disassembly knowledge from CAD-derived virtual assemblies

Shiki Iwase

cs.RO ·submitted 2026-11-09 23:56 UTC · v1

Abstract

Design-stage disassemblability assessment requires knowledge of product structure and the operations available in each assembly state, but CAD assemblies do not directly specify state-dependent disassembly operations. This paper proposes a fastener-centric virtual-disassembly framework that acquires such knowledge from CAD-derived virtual assemblies. Fasteners jointly releasing the same constraint are grouped into operation-level sets, avoiding enumeration of arbitrary individual-fastener orders. Their removability is evaluated through state-dependent visibility and tool-access checks and torque-driven virtual-removal trials. After fastener removal, graph-based reasoning identifies candidate moving units, whose separation is evaluated by initial-motion screening, path generation, and physics-based validation. The acquired operations, states, dependencies, validated paths, and simulation-derived attributes are organized into a Transformed AND/OR Graph for subsequent planning and design evaluation. Exhaustive verification with a controlled toy assembly found no branching violations for introduced tool-accessibility and precedence conditions. Evaluation with a 54-component OpenManipulator Chain gripper demonstrated state-dependent fastener-removal and part- or subassembly-separation operations. Visibility and tool-accessibility evaluations pruned 51.4% of fastener-set candidate evaluations, while removal of obstructing components enabled previously inaccessible fastener operations. Operation-level grouping and screening thereby limited detailed physical validation to mechanically plausible candidates. The results demonstrate the feasibility of acquiring product-specific disassembly knowledge from CAD-derived virtual assemblies before manufacture, supporting subsequent disassembly reasoning and design-for-disassembly evaluation.

Closest papers

Nearest neighbours by meaning across the whole index.

Can It Actually Work? Synthesizing Functional CAD Mechanisms

cs.CV cs.CLcs.GR ·2026-10-19 ·Wenqian Zhang, Yangyi Huang, Zigeng Xu, Weiyang Liu, Zhen Liu
benchmarkcode/data similarity 0.66
Abstract · 45 pages, 16 figures, project page: https://thegenlab.ai/funcad/

While LLM agents can generate visually plausible CAD assemblies, these designs often fail to fulfill their intended physical functions. We study functional CAD design, a setting where agents interpret underspecified requests to construct and iteratively revise mechanisms that satisfy functional requirements in physical simulation. Verifying these requirements is nontrivial: different candidate mechanisms may realize the same function through entirely different components, controls, and operating sequences. To bridge this gap, we propose FunCAD-Harness, a framework that translates abstract requirements into candidate-specific physical tests and uses simulation feedback to guide design revisions. To systematically evaluate this capability, we introduce FunCADBench, a benchmark spanning 46 mechanism families with interdependent and multi-step operations. Experiments across frontier LLM agents show that FunCAD-Harness exposes subtle mechanical failures invisible to visual inspection, substantially improving functional success rates over standard simulation-augmented baselines. Ultimately, our work marks a step toward CAD agents capable of translating human intent into working mechanisms.

0.39

End-to-End Autonomous Generation of Human Assembly Plans

cs.RO cs.GR ·2026-10-07 ·Faustin Arion von Arx, Millicent Schlafly, Mark D. Fuge
code/data similarity 0.64
Abstract · 22 pages, 10 figures

Turning a CAD design into an assembly plan is still largely done by hand, requiring engineers to reason about geometric feasibility, tool access, stability, and the ergonomics of human assembly. In this work, we encode long-established design for assembly (DfA) principles into a contained, end-to-end approach for generating assembly plans. Our approach takes only a mesh assembly and produces either a step-by-step assembly manual or a structured failure report, requiring no joint metadata, fastener annotations, or additional information. Four major components of a manufacturing plan are addressed autonomously: an assembly tool list, the assembly sequence and subassemblies, an assembly manual, and design feedback for improving assemblability. For determining the sequence plan, we systematically disassemble the object in a physics simulator and apply a cost function that encodes DfA principles. Manual generation, tool labelling, and assembly feedback rely primarily on multimodal large language models. Compared with a baseline that always removes the outermost part first from Tian et al., DfA-aware sequence planning reduces simulated assembly time, measured with a robot-arm assembly-time proxy, by 35% on 136 assemblies of 5 to 30 parts. The correct tool is selected for 88.6% of assembly steps. A vision-language model judge compares the generated manuals against ablated variants, identifying which page elements carry the information a reader needs. The presented approach and open-source code are available for use by engineers or AI agents looking to rapidly accelerate the creation of manufacturing plans for a given product design.

0.39

CAD-Based Relation Learning and Geometric-Symbolic Planning for Robotic Assembly

cs.RO ·2026-09-15 ·Fabian Harlacher, Christian Friedrich
similarity 0.61
Abstract · This work has been submitted to Elsevier for possible publication. Copyright may be transferred without notice, after which this version may…

Assembly Sequence Planning (ASP) remains a challenging problem due to its combinatorial nature, making exhaustive planning approaches impractical for complex industrial assemblies. Furthermore, many CAD models lack reliable semantic contact information or require extensive manual preprocessing, limiting the applicability of existing methods. This paper presents a hybrid ASP framework combining learning-based relation extraction with geometric-symbolic reasoning to generate feasible robotic disassembly sequences from imperfect CAD data. A neural network predicts semantic geometric relations from point clouds, while human-in-the-loop verification enables correction of uncertain predictions and planning failures. Extracted relations are transformed into a symbolic assembly graph, enabling a geometric-symbolic planner to efficiently compute locally valid sets of robotic manipulation primitives. A visibility-based ray-casting strategy guides the search for feasible disassembly directions without requiring an exhaustive combinatorial search, while the local solution space enables efficient sequence optimization. The framework is evaluated on an introduced assembly dataset and on the ASAP test dataset. On the ASAP test dataset, the proposed planner achieves an 85.83% planning success rate while reducing the median planning time by more than one order of magnitude across all assembly sizes and by more than a factor of 50 for assemblies with more than 30 components compared to the baseline. The results demonstrate that the proposed hybrid framework enables efficient robotic assembly sequence planning from imperfect CAD data while substantially reducing planning time. By combining learning-based feature segmentation, human-in-the-loop verification, and geometric-symbolic reasoning, the framework provides a practical foundation for scalable and adaptable robotic assembly and disassembly planning.

0.18

LABIT: Long-Horizon Robotic Assembly Benchmark for Industrial Tasks

cs.RO ·2026-10-12 ·Constantin Schempp, Christian Friedrich, Luca Kofler, Laura Suhm
benchmarkcode/data similarity 0.61
Abstract · This work has been submitted to an Elsevier journal for possible publication. Copyright may be transferred without notice, after which this …

Robot learning has undergone significant advancements in the domain of compliant control and robotic assembly. The development of novel methodologies has transcended the capacity to address discrete tasks, such as grasping or inserting, and has evolved to encompass the comprehensive construction of entire assemblies. Conventional benchmarks, which are predominantly focused on single tasks, are no longer adequate to address the complexity and interconnected nature of modern manufacturing processes. Consequently, the necessity for benchmarks to encompass a broader spectrum of assembly and subassembly steps is becoming apparent. In light of these developments, we propose LABIT, an industrial robotic assembly benchmark for long-horizon manipulation. This benchmark encompasses DIN-norm assembly tasks, including screwing, placing, inserting, and snapping, under both high and low tolerance conditions. The successive nature of these assembly steps implies that prior errors can influence subsequent manipulation. Consequently, this benchmark is particularly relevant for assessing the robustness of intelligent robotic systems. The proposed benchmarking protocols and novel performance metric, based on a taxonomy of assembly complexity in conjunction with the comprehensive list of parts and their corresponding CAD models, serve as essential tools for research and development in the field. To provide a baseline, we evaluate the benchmark using traditional force-position control and report reliability and score metrics per primitive, subtask, assembly category, and subassembly. Accompanying data is available at https://irp-hka.github.io/robotic-assembly-benchmark/.

0.48

Automated Assembly Instruction Generation from CAD Models Using Grounded Large Language Models: A Human-in-the-Loop Framework

cs.LG ·2026-10-08 ·Aaron Dsouza, Mohammed Azeez Khan, Ashutosh Mishra, Arshaan Khan, Neha K. Nair +1 more
hot direction similarity 0.61
Abstract · Withdrawal requested as one of the co-authors did not consent to the publication of the manuscript

Assembly documentation is a downstream manufacturing artifact that is still usually authored by interpreting CAD models by hand. Structured product data and large language models are both available, yet studies of CAD interpretation, assembly sequence planning, instruction writing, and human oversight have largely proceeded separately. This paper formulates CAD-grounded assembly instruction generation: the production of natural-language assembly procedures constrained by structured engineering information extracted from CAD models. The proposed framework maps a STEP assembly to a typed ProductGraph intermediate representation, derives a precedence order by deterministic topological sorting, realizes each step as language conditioned only on selected graph context, attaches per-step visual documentation, and applies rule-based and model-assisted checks. PDF export remains disabled until a human reviewer resolves every quality flag. The case study establishes endto-end feasibility on a built-in six-part reference assembly: the pipeline preserves a reported assembly order and carries quantity, material, and torque into an exported manual page. Generalization and geometric validation remain open empirical questions. The contribution is an architecture that separates engineering state, deterministic reasoning, grounded language realization, verification, and human release.

0.21

CADEngBench: It Looks Like CAD, but Does It Work? Evaluating Parametric Design, Assembly Reasoning, and Physics Simulation

cs.AI cs.CVcs.LGcs.RO ·2026-08-10 ·Harmanjot Singh, Abhra Dubey, Jorge Alejandro Amador Herrera
benchmarkhighly cited similarity 0.60
Abstract

A CAD model is not engineering-grade merely because it looks correct. It must satisfy design requirements, respond predictably to parameter changes, support controlled edits, match a reference structural response under a declared analysis, and connect to other parts through valid joints. We present CADEngBench, a two-track benchmark for these capabilities. CADEngBench-P evaluates 300 parametric parts, each used for one zero-to-CAD task and one functional-editing task (600 tasks in total), through boundary-representation (B-Rep) validity, engineering and DFM checks, parameter-family perturbations, functional editing, and matched linear-static FEA in CalculiX. CADEngBench-A evaluates 150 body pairs through ranked joint retrieval, exact face-and-edge grounding, joint-frame prediction, and kinematic verification. Across eight multimodal, code-capable models, editing supplied CAD is substantially easier than generating it, while complex edits and matched FEA remain difficult. Assembly predictions often locate the relevant region but fail to recover the recorded joint or mating entities. These results show that CAD evaluation must test engineering behavior rather than appearance alone.

0.42

From Static Models to Editable CAD: A Design-Intent-Aware Framework for Reverse Parametrization

cs.CG ·2026-10-31 ·Yurim Lee, Sumin Lee, Namwoo Kang
similarity 0.59
Abstract

Neutral CAD formats such as STEP typically preserve geometry but not feature histories or parameter dependencies. Thus, they are inherently limited for iterative design that requires modifications, a critical limitation for design optimization that relies on iterative processes. This study presents a design-intent-aware reverse-parametrization framework that converts history-free STEP parts into editable Grasshopper definitions and represents their assembly relations. Without task-specific training, the framework combines kernel-measured features, geometric relations, a compressed attributed adjacency graph, and multiview renderings. An LLM assigns dimensions independent, fixed, or dependent roles, confirms candidate joints, and interprets verification reports. Kernel- and rule-based modules perform measurement, parameter binding, geometry construction, and verification. Evaluation distinguishes default-shape preservation, design-intent reflection, and edit validity, with the latter examined through assembly-level editing examples involving checks for geometry regeneration, joint alignment, interference, and mechanism closure. As an example, five components of a mechanical mechanism were used, and across 25 runs, the mean global and analytic-feature-region intersection over unions (IoUs) were 0.984 and 0.983, respectively; all runs passed the combined shape-preservation criterion. In a separate request experiment, the requested dimension was selected as an independent variable in 19 of 20 runs. Product-level examples show coordinated changes in part geometry and assembly design while preserving assembly relations and avoiding inter-part interference. These results demonstrate editable reconstruction of history-free CAD models under the evaluated geometric and assembly constraints, indicating potential for subsequent design optimization.

0.20

Backward Layout Search for Sequence-Constrained Robotic Assembly

cs.RO ·2026-08-19 ·Xi Zhang, Jiancong Dai, Hao Chen, Zhengtao Hu, Changcai Yang +1 more
similarity 0.58
Abstract · Submit to ROBIO2026

Robotic assembly layout planning must determine the assembly site and the initial pose of each part while ensuring collision-free execution of a prescribed assembly sequence. This problem is challenging because the obstacle environment changes after each assembly step, and unassembled parts re maining in the workspace may block robot motions. We observe that the feasibility of each assembly step depends only on the initial poses of the current and later-assembled parts. Based on this dependency, we propose Backward Layout Search (BLS), which assigns initial part poses in reverse assembly order. Each expansion performs geometric, kinematic, grasp, and prescribed-motion checks, while collision masks and candidate set filtering remove infeasible initial part pose candidates. Promising partial layouts are retained through beam selection, and complete layouts are validated by full motion planning in forward assembly order. Experiments on five assembly models show that BLS produces collision-free executable layouts and reduces step evaluations and search time compared with a matched forward search.

0.31