CS Paper Radar

Band-Selective Microwave Cavity Optimization Using Differentiable FDTD: Gradient-Guided Search Versus Structured Random Search

Hasan Yiğit, Kutlu Karayahşi

eess.SP ·submitted 2026-08-20 09:15 UTC · v1
benchmarkunusual

Abstract

We compare gradient-based inverse design with structured random search for dielectric-loaded microwave cavities using an in-house JAX-based differentiable FDTD solver. The benchmark fixes material fraction, filtered density representation, initialization, band-energy objective, and measured selection wall time. Each selected design is evaluated in a separate 8000-step FDTD simulation. Across four target bands, three prescribed material fractions, and six seeds, gradient optimization achieves a higher in-band spectral-energy fraction in all 72 paired comparisons. The mean paired improvement is 0.356, with a 95 percent paired bootstrap interval of 0.339-0.374 and an exact two-sided sign-flip p value of 0.03125. Gradient, cavity-mode, CFL, material-fraction, and raw-output integrity checks pass before inference. Under matched material and computational budgets, the results support an advantage for gradient-based optimization in this cavity-design benchmark.

Comment
This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may no longer be accessible

Closest papers

Nearest neighbours by meaning across the whole index.

Simulator-Refined Diffusion for Radio-Frequency Inverse Design

cs.LG cs.AI ·2026-09-29 ·Jinhao Liang, Jacob K. Christopher, Michael Frei, Tommaso Dreossi, Nando Fioretto
similarity 0.56
Abstract

Diffusion models have shown potential in inverse design of printed circuit boards (PCBs), enabling the generation of layouts conditioned on target S-parameters. Despite this promise, applying diffusion models to PCB layout generation remains challenging due to their difficulty in meeting the quantitative electromagnetic specifications. A common approach is gradient-based guidance, which biases the diffusion sampling process with the gradient of an objective used for evaluation. However, full-wave electromagnetic simulators are accurate but expensive and typically non-differentiable, whereas differentiable surrogates are informative but not always reliable. To address these limitations, this paper proposes Simulator-Refined Diffusion (SRD), a novel combination of a low-fidelity differentiable surrogate and a high-fidelity non-differentiable simulator within the diffusion sampling process. Unlike standard zeroth-order optimization, which requires a great number of random perturbations, our approach uses the surrogate's gradient to propose the perturbation direction while the simulator then searches based on this direction to identify an effective design update. Experimental results across different settings show that this method consistently outperforms current state-of-the-art methods, producing layouts whose simulated S-parameters match the target specifications up to 21.2% closer for in-distribution targets and up to 19.8% for out-of-distribution targets.

0.15

Differentiable Synthesis and Yield Optimization of Cross-Coupled Resonator Filters

eess.SP math.OC ·2026-09-15 ·Orion Georgiou
similarity 0.54
Abstract · 17 pages, 6 figures, 12 tables

Coupling-matrix synthesis of cross-coupled resonator filters is difficult when the desired topology is noncanonical. Automatic differentiation removes the need for problem-specific sensitivity expressions, but does not by itself overcome the nonconvex optimization landscape. This work develops a staged differentiable synthesis framework and identifies the importance of its initial objective through a controlled comparison that varies only the objective of the first optimization phase. For tenth- and sixteenth-order benchmarks, directly matching a frequency-sampled response under the prescribed topology reaches the target from $0$ of $24$ and $0$ of $12$ random starts, respectively. Replacing the first-stage objective with characteristic-polynomial matching increases the success rate to $18$ of $24$ and $12$ of $12$ (exact paired $p=7.6\times10^{-6}$ and $4.9\times10^{-4}$). The observed difference is not explained by local conditioning and is consistent with saturation of the bounded response residual far from the solution. A differentiable front end converts symmetric multiband specifications into target polynomials and, when applied end to end to a fabricated dual-band filter specification, finds a realization with one fewer cross-coupling than the published design. Finally, differentiating through Monte Carlo tolerance simulations enables yield-driven design centering, increasing the model-predicted yield from $50.9\%$ to $67.0\pm0.5\%$ under an additive coupling-error model, an improvement of $16.1$ percentage points.

0.26

Delayed Convergence of S-Parameter Sensitivities to Design Parameters in FDTD Simulations

eess.SP physics.comp-ph ·2026-10-20 ·Byungkwan Kim
similarity 0.54
Abstract · 10 pages, 7 figures. Submitted to IEEE Transactions on Microwave Theory and Techniques

In the finite-difference time-domain (FDTD) method, the sensitivities of S-parameters to design parameters come from discrete Fourier transforms of responses ending at a simulation time T. We show that, when a design parameter moves a resonance, the sensitivity converges later than the S-parameter. For a single mode with field decay time $τ$, the truncation error of the sensitivity is $(1+T/τ)e^{-T/τ}$, against $e^{-T/τ}$ for the resonant part of the S-parameter, so a 1% sensitivity error needs $T \geq 6.6τ$ instead of $4.6τ$. Automatic differentiation, the discrete adjoint and finite differences on the same run carry this error, so their agreement cannot reveal it. In three solvers, with no fitted parameter, the estimate predicts the simulated error within 4% at cavity resonances with $Q$ of 1000-7000; at lower $Q$ the error is larger. On a cavity whose slowest mode is weakly coupled, common end criteria leave $|S_{11}|$ within 0.5 dB of a 1.3 dB dip but its sensitivity 10-72% in error. A matrix-pencil extrapolation inside the differentiable computation recovers the sensitivity on a cavity with field probes from a run 66 times shorter. In a single-pole filter loop with a symmetric objective, truncation leaves the maximum of the objective in place, and the optimizer reaches the resonance of a full run despite the wrong gradient. With two coupled poles, the truncated objective moves the optimum: on runs of $1τ$ it over-couples by $Δk \approx 1.24/Q$, and an equal-ripple objective still shifts it by about $0.2\barα$ at $3τ$, but not at $4.6τ$.

0.28

AbsorbEvo: An Agentic Framework for Autonomous Inverse Design of Microwave Absorbers

cs.AI ·2026-10-01 ·Zhicheng Feng, Yubo Zhao, Xuefeng Yao
similarity 0.52
Abstract

Designing high-performance microwave absorbers requires specialized expertise in electromagnetic theory, materials science and simulation programming, and entails time-consuming optimization. Here, we present AbsorbEvo, an agentic framework for autonomous inverse design that translates natural-language performance objectives into designs verified by full-wave simulations. Its candidate evolution strategy integrates language reasoning, physics-based prediction and historical feedback. A large language model proposes the directions and magnitudes of parameter adjustments based on task objectives and computational history. The system combines directed increments with global sampling to generate candidates and uses a low-cost predictive model as a physics prior to rank them. Only high-ranking designs undergo full-wave simulation. Results passing physical validity checks are used to evaluate performance and guide subsequent search. Experience from training tasks is further distilled into textual skills, which are independently validated before use in new tasks. Under identical proposal budgets on held-out AbsorbBench-36 tasks, AbsorbEvo achieved a task success rate of 79.17%, versus 25.00% for a generic agent and 12.50% for random search. Its mean best coverage was 0.7816, compared with 0.6434 and 0.6448, respectively. By integrating language reasoning and physics-based feedback into design decisions, AbsorbEvo provides a methodological foundation for natural-language-driven autonomous inverse design of microwave absorbers.

0.25

Multi-Label Classification with Constrained Search for Inverse Design of a 16x16 Reconfigurable Pixel Antenna

eess.SP ·2026-11-11 ·Nadeem Rather, Holger Claussen, Lester Ho
similarity 0.52
Abstract

In this paper, an inverse design method is presented for a 16x16 reconfigurable pixel antenna with 480 binary switches, giving 2480 possible patterns, far beyond what full-wave simulation can explore. Given a target frequency between 1 and 6 GHz, the method searches for a switch configuration whose simulated resonance lies close to the target. A forward surrogate model is trained on 22,152 full- wave simulated patterns to predict where a given switch pattern resonates. The forward task is formulated as multi-label classification over 100 frequency bins rather than reflection-coefficient regression, because a curve-fitting objective is dominated by the flat baseline around the narrow resonances of this structure. The inverse design is a simulated annealing search over the switch state, with a connectivity constraint maintained at every step so that every pattern generated is a valid antenna. The proposed methodology combines resonance-focused surrogate modelling with connectivity-constrained discrete optimization, enabling candidate generation without full-wave solver calls during the search. The pipeline is verified in CST Microwave Studio by simulating 220 predicted candidates, ten for each of 22 target frequencies. For each request, the best of the ten candidates reached a median frequency error of 23 MHz across the 22 targets, compared with 35 MHz for a solver-guided search using 200 simulations for each target. The proposed methodology therefore enables automatic switch configuration to achieve a requested resonant frequency, eliminating solver calls during the search and manual redesign of the antenna geometry.

0.18

Diffusion-Based Inverse Design of Dielectric Resonator Metasurfaces for Shaping Smart Electromagnetic Environments

cs.LG physics.app-phphysics.comp-ph ·2026-08-30 ·M. Tsukerman, K. Grotov, D. Vovchuk, P. Ginzburg
similarity 0.50
Abstract

Future wireless systems are expected to transform the surrounding space from a passive propagation medium into a smart electromagnetic environment, where engineered surfaces control wave propagation, support wireless sensing, and create programmable electromagnetic fingerprints. A key challenge in realizing this vision is the inverse design of metasurfaces for tailored electromagnetic propagation. While forward analysis evaluates the response of a known geometry, the inverse task starts from a prescribed scattering signature and seeks a physically realizable structure that produces it. This inverse task is inherently nonlinear and often high-dimensional, while candidate solutions may be non-unique and provide no direct indication of practical realizability. Here, we introduce a conditional diffusion framework for inverse design of dielectric resonator metasurfaces from target angular scattering patterns. Trained on T-matrix simulated geometry-response pairs, the model learns a conditional distribution of geometries instead of a deterministic mapping, enabling multiple candidate designs for the ill-posed inverse problem. The best generated metasurface achieves a mean percentage error of 1.39%, outperforming CMA-ES optimization (4.1% after 10 h) while requiring only about one minute for after-training inference. The model also produces lower error distributions than deterministic neural baselines for out-of-distribution spectra, highlighting the potential of diffusion models for efficient metasurface design.

0.28

Machine Learning Assisted Inverse Design of Pixelated mmWave Patch Antennas

eess.SP cs.AI ·2026-08-24 ·Nadeem Rather, Holger Claussen, Lester Ho
published similarity 0.50
Abstract

A machine learning-assisted framework for the inverse design of pixelated millimetre-wave patch antennas targeting the 22--30 GHz band is presented. The antenna surface is represented as a 19x23 binary pixel grid on a Rogers RT/duroid 5880 substrate, where each pixel is either metal or empty, with a continuous electrical path from the feed enforced by design. An initial dataset of approximately 6,000 full-wave CST simulations was collected from structured random pixel patterns, of which only around 40% achieved a resonance with |S11| <= -10 dB anywhere in the band, resulting in an imbalanced dataset. To improve simulation efficiency, an XGBoost binary classifier was trained on this data to distinguish resonant from non-resonant patterns before simulation. Using the classifier as a pre-simulation filter, an additional 4,000 patterns were selected and simulated, raising the overall proportion of resonant designs in the combined 10,000-sample dataset from approximately 40% to 52%. A hybrid CNN-BiLSTM forward surrogate was then trained on this augmented dataset to predict the full complex S11 response across 801 frequency points, using a physics-guided composite loss that explicitly emphasises resonance dip accuracy. Finally, an inverse design model was developed that optimises in a compact 64-dimensional latent space using gradient descent to generate pixel patterns matching a desired S11 specification. The results show good agreement between the surrogate-predicted and CST-simulated |S11| responses for the generated designs and demonstrate the feasibility of automatically designing and reconfiguring antenna structures.

0.64

K-TRAIL: Simulator-Guided Generative Design of EM/RF Circuits

cs.LG ·2026-09-19 ·Piyush Saha, Evan Newell, Hanna O'Leary, Arun Natarajan, Alireza Aghasi
similarity 0.49
Abstract

Inverse design of RF and electromagnetic (EM) circuits is challenging because the relationship between circuit layout and electrical response is non-unique, and full-wave simulation is computationally expensive. This paper presents K-TRAIL, a simulator-guided generative framework for automated EM/RF circuit synthesis. K-TRAIL combines diffusion-based layout generation with derivative-free ensemble Kalman guidance, allowing feedback from a black-box EM simulator to refine candidate layouts during generation without requiring adjoint sensitivities or differentiable solver models. The framework supports both synthesis from prescribed S-parameter responses and synthesis directly from RF performance constraints. Experiments on multi-layer RFIC structures show that simulator-guided generation improves agreement with target responses and can identify structurally distinct layouts that satisfy circuit-level design requirements. The proposed approach provides a practical path toward generative, verification-aware RF circuit design while retaining the flexibility to explore diverse layout topologies.

0.52