CS Paper Radar

Delayed Convergence of S-Parameter Sensitivities to Design Parameters in FDTD Simulations

Byungkwan Kim

eess.SP physics.comp-ph ·submitted 2026-10-20 16:40 UTC · v1

Abstract

In the finite-difference time-domain (FDTD) method, the sensitivities of S-parameters to design parameters come from discrete Fourier transforms of responses ending at a simulation time T. We show that, when a design parameter moves a resonance, the sensitivity converges later than the S-parameter. For a single mode with field decay time $τ$, the truncation error of the sensitivity is $(1+T/τ)e^{-T/τ}$, against $e^{-T/τ}$ for the resonant part of the S-parameter, so a 1% sensitivity error needs $T \geq 6.6τ$ instead of $4.6τ$. Automatic differentiation, the discrete adjoint and finite differences on the same run carry this error, so their agreement cannot reveal it. In three solvers, with no fitted parameter, the estimate predicts the simulated error within 4% at cavity resonances with $Q$ of 1000-7000; at lower $Q$ the error is larger. On a cavity whose slowest mode is weakly coupled, common end criteria leave $|S_{11}|$ within 0.5 dB of a 1.3 dB dip but its sensitivity 10-72% in error. A matrix-pencil extrapolation inside the differentiable computation recovers the sensitivity on a cavity with field probes from a run 66 times shorter. In a single-pole filter loop with a symmetric objective, truncation leaves the maximum of the objective in place, and the optimizer reaches the resonance of a full run despite the wrong gradient. With two coupled poles, the truncated objective moves the optimum: on runs of $1τ$ it over-couples by $Δk \approx 1.24/Q$, and an equal-ripple objective still shifts it by about $0.2\barα$ at $3τ$, but not at $4.6τ$.

Comment
10 pages, 7 figures. Submitted to IEEE Transactions on Microwave Theory and Techniques

Closest papers

Nearest neighbours by meaning across the whole index.

Band-Selective Microwave Cavity Optimization Using Differentiable FDTD: Gradient-Guided Search Versus Structured Random Search

eess.SP ·2026-08-20 ·Hasan Yiğit, Kutlu Karayahşi
benchmarkunusual similarity 0.54
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

We compare gradient-based inverse design with structured random search for dielectric-loaded microwave cavities using an in-house JAX-based differentiable FDTD solver. The benchmark fixes material fraction, filtered density representation, initialization, band-energy objective, and measured selection wall time. Each selected design is evaluated in a separate 8000-step FDTD simulation. Across four target bands, three prescribed material fractions, and six seeds, gradient optimization achieves a higher in-band spectral-energy fraction in all 72 paired comparisons. The mean paired improvement is 0.356, with a 95 percent paired bootstrap interval of 0.339-0.374 and an exact two-sided sign-flip p value of 0.03125. Gradient, cavity-mode, CFL, material-fraction, and raw-output integrity checks pass before inference. Under matched material and computational budgets, the results support an advantage for gradient-based optimization in this cavity-design benchmark.

0.28

Differentiable Synthesis and Yield Optimization of Cross-Coupled Resonator Filters

eess.SP math.OC ·2026-09-15 ·Orion Georgiou
similarity 0.51
Abstract · 17 pages, 6 figures, 12 tables

Coupling-matrix synthesis of cross-coupled resonator filters is difficult when the desired topology is noncanonical. Automatic differentiation removes the need for problem-specific sensitivity expressions, but does not by itself overcome the nonconvex optimization landscape. This work develops a staged differentiable synthesis framework and identifies the importance of its initial objective through a controlled comparison that varies only the objective of the first optimization phase. For tenth- and sixteenth-order benchmarks, directly matching a frequency-sampled response under the prescribed topology reaches the target from $0$ of $24$ and $0$ of $12$ random starts, respectively. Replacing the first-stage objective with characteristic-polynomial matching increases the success rate to $18$ of $24$ and $12$ of $12$ (exact paired $p=7.6\times10^{-6}$ and $4.9\times10^{-4}$). The observed difference is not explained by local conditioning and is consistent with saturation of the bounded response residual far from the solution. A differentiable front end converts symmetric multiband specifications into target polynomials and, when applied end to end to a fabricated dual-band filter specification, finds a realization with one fewer cross-coupling than the published design. Finally, differentiating through Monte Carlo tolerance simulations enables yield-driven design centering, increasing the model-predicted yield from $50.9\%$ to $67.0\pm0.5\%$ under an additive coupling-error model, an improvement of $16.1$ percentage points.

0.26

Discontinuity-Aware Solvers for Vapor-Compression Cycles

cs.MS math.NA ·2026-11-15 ·Shreyas Ekanathan, Avinash Subramanian, Oscar Smith, Yingbo Ma, Christopher Rackauckas +1 more
code/data similarity 0.47
Abstract

Physics-based models of vapor-compression cycles are often formulated as large, stiff DAE systems with derivative discontinuities introduced at the points of phase change. We use an implementation of a discontinuity-aware ODE and DAE solver scheme that uses domain-specific, user-declared information to compute appropriate time steps for more efficient integration. This scheme is made open-source within Julia's DifferentialEquations package. We demonstrate how discontinuity information can be specified symbolically in a declarative modeling language such as Dyad and passed to the solver to address the numerical challenges posed. We apply this discontinuity-aware technique to two applications: first, a scalar ODE with two discontinuities, and then a model of a full vapor-compression cycle. The discontinuity-aware solver yields significantly fewer step rejections and improved solver times, particularly with the Rodas5P solver at loose tolerances, as compared to standard error control, suggesting that exposing physical discontinuity information from equation-oriented models to adaptive solvers can improve practical simulation performance without requiring reassembly of the model.

0.47

Maxwell's equations are universal for sparse linear algebra

cs.CC physics.optics ·2026-10-28 ·Yannick Augenstein
theorycode/dataunusual similarity 0.44
Abstract · 109 pages (18 pages main text, 91 pages Supplementary Information), 8 figures, 4 tables. v2: adds numerical illustrations (Fig. 3, SI Part V…

Optical and wave-based analog computing has re-emerged as a route to accelerating linear algebra, with metamaterials and photonic circuits shown to invert matrices and solve integral equations. However, it has remained unclear which problems such passive structures can represent, and at what cost, once encoding, precision, conditioning and readout are accounted for. Here, we show that every polynomially conditioned sparse linear system can be compiled into a three-dimensional dielectric -- a cavity filled with lossless, isotropic material of bounded permittivity -- whose time-harmonic response encodes its solution. For $m$ nonzero coefficients, the volume of the structure and the cost of writing it down and reading out the answer scale as $\tilde O(m^{3/2})$, coefficients require only $O(\log m)$ bits, and every field that approximately satisfies Maxwell's equations decodes to an approximate solution. We prove the construction for the continuum equations and give a computer-assisted version for the Yee discretization underlying finite-difference solvers. Read in reverse, it implies that electromagnetic simulation is, up to this overhead, as hard as general sparse linear algebra: a sufficiently fast general-purpose Maxwell solver would yield a faster sparse linear solver.

0.50

Identification of $dq$-Asymmetric Impedances as Complex Transfer Functions Using a Single Arbitrary Excitation

eess.SP eess.SY ·2026-08-30 ·Mohamed Abdalmoaty, Zheran Zeng, Dongsheng Yang, Florian Dörfler
similarity 0.43
Abstract

Cross-coupling between the $dq$ coordinates makes the identification of asymmetric grid impedances a challenging problem, particularly near the fundamental frequency where the asymmetric coupling is strongest. Existing schemes usually handle it either by perturbing the two coordinates sequentially, which lengthens the measurement, or by using a time-domain method with a global parametric model whose order must be tuned. This paper develops a single-shot active non-parametric frequency-domain method that avoids both. The equivalent impedance is parameterized by a pair of single-input single-output complex transfer functions. Each spectral line is fitted with a local rational model; the leakage and transient contributions are estimated, so that neither periodic steady-state excitation nor repeated excitation cycles are required. We give the exact finite-time discrete Fourier transform relation for the conjugate-coupled complex-signal model, and analyse the distortion that a stationary-frame filter placed ahead of the Park transform imposes on the identified pair. The method is validated on a controller hardware-in-the-loop platform against an analytically derived small-signal model, for a symmetric grid and for the same grid with an added grid-following converter that renders it asymmetric. Both complex transfer functions and all four real transfer functions of the $dq$ impedance are recovered over a wide band from a single one-second record of a random excitation, at 1 Hz resolution.

0.26

Simulator-Refined Diffusion for Radio-Frequency Inverse Design

cs.LG cs.AI ·2026-09-29 ·Jinhao Liang, Jacob K. Christopher, Michael Frei, Tommaso Dreossi, Nando Fioretto
similarity 0.42
Abstract

Diffusion models have shown potential in inverse design of printed circuit boards (PCBs), enabling the generation of layouts conditioned on target S-parameters. Despite this promise, applying diffusion models to PCB layout generation remains challenging due to their difficulty in meeting the quantitative electromagnetic specifications. A common approach is gradient-based guidance, which biases the diffusion sampling process with the gradient of an objective used for evaluation. However, full-wave electromagnetic simulators are accurate but expensive and typically non-differentiable, whereas differentiable surrogates are informative but not always reliable. To address these limitations, this paper proposes Simulator-Refined Diffusion (SRD), a novel combination of a low-fidelity differentiable surrogate and a high-fidelity non-differentiable simulator within the diffusion sampling process. Unlike standard zeroth-order optimization, which requires a great number of random perturbations, our approach uses the surrogate's gradient to propose the perturbation direction while the simulator then searches based on this direction to identify an effective design update. Experimental results across different settings show that this method consistently outperforms current state-of-the-art methods, producing layouts whose simulated S-parameters match the target specifications up to 21.2% closer for in-distribution targets and up to 19.8% for out-of-distribution targets.

0.15

Time-Domain Data-Driven Loewner Reduced-Order Models for Electromagnetic Simulation

eess.SP physics.comp-ph ·2026-10-15 ·Pablo Biurrun, Carlos J. Ramos-Salas, Luis D. Angulo, Valentin de la Rubia
similarity 0.42
Abstract

This paper presents a data-driven Loewner framework for constructing reduced-order models (ROMs) from time-domain electromagnetic (EM) simulation data. High-fidelity simulation of microwave devices can be computationally expensive, particularly when fine spatial discretization and long observation windows are required. The proposed method uses transient input-output data to construct Loewner and shifted Loewner matrices, from which a reduced descriptor realization is obtained through singular value decomposition (SVD). The resulting models are identified from a limited training window and used to predict responses over substantially longer time intervals, with prediction windows up to 50 times the duration of the training window. The method is formalized as an explicit, reproducible algorithm and validated against full-order simulations for four microwave structures: a substrate-integrated-waveguide filter, a frequency-selective surface, an evanescent-mode coaxial comb-line filter, and a diplexer. The results demonstrate the potential of Loewner-based identification to provide compact models of electromagnetic responses while reducing the need for repeated full-order simulation.

0.23

FDM+: A Framework for Constrained Control of the 2D Radiative Transport Equation

cs.LG physics.comp-ph ·2026-11-18 ·Hualing Zhong, Shuai Wang, Hui Xie, Heng Yong
similarity 0.42
Abstract

Applying the frozen diffusion model (FDM) [29] to the constrained control of the 2D radiative transport equation presents several challenges. These include the dimensional difference between control variables and state functions, the resolution mismatch between traditional numerical solvers and deep learning models, and solution non-uniqueness. To address these obstacles, we propose a novel approach, FDM+, which includes three key improvements. Firstly, a decoupled prediction architecture is introduced to address the dimensional heterogeneity. Secondly, an efficient parameterization strategy resolves the resolution mismatch. Meanwhile, we derive a total error bound to analyze how the parameterization error and the model estimation error jointly affect the performance. Thirdly, the conditional distribution learned by the diffusion model is leveraged to perform design space exploration for multi-solution problems. A series of numerical experiments demonstrate that FDM+ outperforms existing methods in reconstruction accuracy and design flexibility.

0.33