CS Paper Radar

Differentiable Synthesis and Yield Optimization of Cross-Coupled Resonator Filters

Orion Georgiou

eess.SP math.OC ·submitted 2026-09-15 07:19 UTC · v1

Abstract

Coupling-matrix synthesis of cross-coupled resonator filters is difficult when the desired topology is noncanonical. Automatic differentiation removes the need for problem-specific sensitivity expressions, but does not by itself overcome the nonconvex optimization landscape. This work develops a staged differentiable synthesis framework and identifies the importance of its initial objective through a controlled comparison that varies only the objective of the first optimization phase. For tenth- and sixteenth-order benchmarks, directly matching a frequency-sampled response under the prescribed topology reaches the target from $0$ of $24$ and $0$ of $12$ random starts, respectively. Replacing the first-stage objective with characteristic-polynomial matching increases the success rate to $18$ of $24$ and $12$ of $12$ (exact paired $p=7.6\times10^{-6}$ and $4.9\times10^{-4}$). The observed difference is not explained by local conditioning and is consistent with saturation of the bounded response residual far from the solution. A differentiable front end converts symmetric multiband specifications into target polynomials and, when applied end to end to a fabricated dual-band filter specification, finds a realization with one fewer cross-coupling than the published design. Finally, differentiating through Monte Carlo tolerance simulations enables yield-driven design centering, increasing the model-predicted yield from $50.9\%$ to $67.0\pm0.5\%$ under an additive coupling-error model, an improvement of $16.1$ percentage points.

Comment
17 pages, 6 figures, 12 tables

Closest papers

Nearest neighbours by meaning across the whole index.

Band-Selective Microwave Cavity Optimization Using Differentiable FDTD: Gradient-Guided Search Versus Structured Random Search

eess.SP ·2026-08-20 ·Hasan Yiğit, Kutlu Karayahşi
benchmarkunusual similarity 0.54
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

We compare gradient-based inverse design with structured random search for dielectric-loaded microwave cavities using an in-house JAX-based differentiable FDTD solver. The benchmark fixes material fraction, filtered density representation, initialization, band-energy objective, and measured selection wall time. Each selected design is evaluated in a separate 8000-step FDTD simulation. Across four target bands, three prescribed material fractions, and six seeds, gradient optimization achieves a higher in-band spectral-energy fraction in all 72 paired comparisons. The mean paired improvement is 0.356, with a 95 percent paired bootstrap interval of 0.339-0.374 and an exact two-sided sign-flip p value of 0.03125. Gradient, cavity-mode, CFL, material-fraction, and raw-output integrity checks pass before inference. Under matched material and computational budgets, the results support an advantage for gradient-based optimization in this cavity-design benchmark.

0.28

Delayed Convergence of S-Parameter Sensitivities to Design Parameters in FDTD Simulations

eess.SP physics.comp-ph ·2026-10-20 ·Byungkwan Kim
similarity 0.51
Abstract · 10 pages, 7 figures. Submitted to IEEE Transactions on Microwave Theory and Techniques

In the finite-difference time-domain (FDTD) method, the sensitivities of S-parameters to design parameters come from discrete Fourier transforms of responses ending at a simulation time T. We show that, when a design parameter moves a resonance, the sensitivity converges later than the S-parameter. For a single mode with field decay time $τ$, the truncation error of the sensitivity is $(1+T/τ)e^{-T/τ}$, against $e^{-T/τ}$ for the resonant part of the S-parameter, so a 1% sensitivity error needs $T \geq 6.6τ$ instead of $4.6τ$. Automatic differentiation, the discrete adjoint and finite differences on the same run carry this error, so their agreement cannot reveal it. In three solvers, with no fitted parameter, the estimate predicts the simulated error within 4% at cavity resonances with $Q$ of 1000-7000; at lower $Q$ the error is larger. On a cavity whose slowest mode is weakly coupled, common end criteria leave $|S_{11}|$ within 0.5 dB of a 1.3 dB dip but its sensitivity 10-72% in error. A matrix-pencil extrapolation inside the differentiable computation recovers the sensitivity on a cavity with field probes from a run 66 times shorter. In a single-pole filter loop with a symmetric objective, truncation leaves the maximum of the objective in place, and the optimizer reaches the resonance of a full run despite the wrong gradient. With two coupled poles, the truncated objective moves the optimum: on runs of $1τ$ it over-couples by $Δk \approx 1.24/Q$, and an equal-ripple objective still shifts it by about $0.2\barα$ at $3τ$, but not at $4.6τ$.

0.28

Multi-Label Classification with Constrained Search for Inverse Design of a 16x16 Reconfigurable Pixel Antenna

eess.SP ·2026-11-11 ·Nadeem Rather, Holger Claussen, Lester Ho
similarity 0.48
Abstract

In this paper, an inverse design method is presented for a 16x16 reconfigurable pixel antenna with 480 binary switches, giving 2480 possible patterns, far beyond what full-wave simulation can explore. Given a target frequency between 1 and 6 GHz, the method searches for a switch configuration whose simulated resonance lies close to the target. A forward surrogate model is trained on 22,152 full- wave simulated patterns to predict where a given switch pattern resonates. The forward task is formulated as multi-label classification over 100 frequency bins rather than reflection-coefficient regression, because a curve-fitting objective is dominated by the flat baseline around the narrow resonances of this structure. The inverse design is a simulated annealing search over the switch state, with a connectivity constraint maintained at every step so that every pattern generated is a valid antenna. The proposed methodology combines resonance-focused surrogate modelling with connectivity-constrained discrete optimization, enabling candidate generation without full-wave solver calls during the search. The pipeline is verified in CST Microwave Studio by simulating 220 predicted candidates, ten for each of 22 target frequencies. For each request, the best of the ten candidates reached a median frequency error of 23 MHz across the 22 targets, compared with 35 MHz for a solver-guided search using 200 simulations for each target. The proposed methodology therefore enables automatic switch configuration to achieve a requested resonant frequency, eliminating solver calls during the search and manual redesign of the antenna geometry.

0.18

Route-Aware EM Surrogate for Automated LC Matching Network Optimization

cs.AR eess.SP ·2026-10-30 ·Subhadip Ghosh, Surya Srikar Peri, Ramesh Harjani, Sachin S. Sapatnekar
code/data similarity 0.48
Abstract · Submitted to the IEEE International Symposium on Circuits and Systems (ISCAS) 2027

This paper proposes an open-source automated LC matching network optimization framework that combines schematic-level design optimization with electromagnetic (EM)-aware post-layout refinement. An ML-based surrogate predicts the frequency-dependent complex admittance of individual routes, enabling reuse across matching network topologies and physical layouts for the same technology node without retraining. These route models guide post-layout passive retuning to recover matching performance while preserving the layout footprint. Evaluated in a commercial 65nm CMOS technology, the surrogate achieves 1.94-4.91% mean absolute percentage error with respect to a full-wave electromagnetic solver, with no detected passivity violations. Across nine LC matching networks operating at 5-95GHz, our framework recovers S_11 from -6.37dB, for schematic-level optimization after post-layout degradation to -22.27dB after EM-aware post-layout refinement. All designs meet matching targets under full-layout EM verification in optimization runtimes below 70s.

0.34

Delta-Seeker: Closed-Loop Generative Search for Novel Circuit Design Discovery

eess.SY ·2026-10-30 ·Dinithi Jayasuriya, Devangshu Dutta, Aravind Saravanan, Nilesh Ahuja, Amanda Rios +1 more
similarity 0.47
Abstract

Generative models are increasingly used for circuit synthesis and optimization by proposing topologies, sizing devices, and exploring large design spaces. We investigate whether they can instead support design discovery, where generated structures must depart from known designs while producing reproducible electrical behavior. We propose Delta-Seeker, a closed-loop circuit search framework that combines discrete diffusion for topology generation and mutation with structural checking, SPICE-in-the-loop sizing, Pareto selection, and feedback from prior search outcomes. The search controller uses progress and recurring structural failures to allocate evaluation effort and steer subsequent topology generation, while independent re-sizing and operating-corner analysis are performed only after search. In generator-only experiments, cross-generation feedback increases structurally valid children from 143 to 945 and reduces the faulty-candidate fraction from 0.925 to 0.761. In op-amp topology discovery at matched sizing cost, Delta-Seeker yields 54 designs that remain feasible in at least three of four independent re-sizings and 18 that additionally pass device-level checks and supply-temperature corner analysis, compared with 38 and 10 under fixed control. Removing cross-generation memory reduces independently robust discoveries from 54 to 43 and seven-corner robust discoveries from 40 to 27. In DC-DC converter search, nearest-parent analysis identifies a corpus-absent topology whose generated switching current path changes its nearest training-corpus parent from infeasible at all four operating corners to feasible at all four, while increasing median efficiency from 31.2% to 98.96%. These results show that closed-loop generative search can support circuit discovery beyond structural novelty by identifying new topologies with independently verified changes in circuit operation.

0.33

End-to-End Neural Modeling of EM Response and Design Performance for Free-Form RFIC Passives

eess.SP cs.LG ·2026-10-25 ·Yuhao Mao, Chenhao Chu, Martin Vechev, Hua Wang
publisheddatasetcode/data similarity 0.47
Abstract · NeurIPS'26

Passive matching networks are critical components in radio-frequency integrated circuits (RFICs), but their design is bottlenecked by expensive finite-difference-based electromagnetic (EM) simulation. We propose an end-to-end neural framework for free-form RFIC passives that predicts both EM response and downstream design performance under varying frequency and circuit contexts, combining a frequency-conditioned neural simulator with a circuit-conditioned neural solver. To improve design performance prediction, the simulator outputs a neural EM response consisting of both the explicit EM response and a complementary response, together with a dependence regularizer that encourages the two responses to capture orthogonal information. To evaluate the proposed framework, we construct a large-scale dataset of free-form passive layouts, synthesized from both expert-designed contours and random paths. Our 21M-parameter model achieves high accuracy across a broad frequency range, circuit contexts and passive matching settings, with $R^2>0.98$ for almost all targets, while providing orders-of-magnitude faster evaluation than traditional EM simulation. Code available at https://github.com/ETH-IDEAS/RFIC-NeuralSim.

0.37

Co-designing a Layered Control Architecture

eess.SY math.OC ·2026-10-14 ·Chris Verhoek, Charis Stamouli, George J. Pappas, Nikolai Matni
similarity 0.45
Abstract · 19 pages, extended version

Layered control architectures (LCAs) are ubiquitous in complex engineering systems. However, in practice they are largely designed ad hoc and mostly dictated by the experience of the designer. This is because there is currently no systematic and practically applicable theory available to holistically design LCAs. Hence, systematically reasoning about the optimality, stability, and feasibility of the LCA design is not possible. We set a first step toward such a theory by presenting a framework for co-designing a two-layer LCA for a linear time-invariant plant. The resulting co-design problem optimizes over architectural design variables (e.g., reduced order model dimension and sampling ratio between the layers) and tuning-based design variables (e.g., the numerical values of the feedback gain or the matrices of the reduced order model), all subject to constraints that ensure stability, feasibility, and compute properties of the closed-loop LCA. The proposed formulation allows to make informed tradeoffs along the Pareto front traced over different axes of optimality, e.g., speed, accuracy or computational effort. We demonstrate the effect of making various tradeoffs in a simple numerical example.

0.45

LOADBench: A Large Open Analog Dataset and Benchmark for Machine Learning in IC Design

cs.AI ·2026-10-15 ·M. Leibl, F. Azevedo, S. Uhlich, A. Bonetti, A. Venkitaraman +5 more
publishedbenchmarkcode/data similarity 0.45
Abstract · Dataset available on zenodo: https://zenodo.org/records/21759759 9 pages, 6 figures, Conference: MLCAD '26: 8th ACM/IEEE International Sympo…

Machine learning (ML) for analog IC design is constrained by limited open data and the absence of standardized evaluation: results reported in different papers are typically obtained on bespoke, often closed, datasets and with ad-hoc metrics, leaving comparisons across methods unreliable. We address both gaps with a large opensource dataset and a suite of standardized benchmarks. The dataset contains more than 100 operational amplifier (opamp) topologies (1-, 2-, and 3-stage) in the SkyWater130 PDK, each shipped with structural and functional annotations, topology-specific sizing constraints (symmetry and sizing rules), an Ngspice testbench, and a multi-objective NSGA-II sizing run producing around 103 Pareto-optimal and 106 intermediate sizing-performance pairs per topology. On top of this data we define six benchmark tasks with precise protocols: inverse sizing, topology selection, sub-circuit classification, structural circuit generation, Pareto-membership prediction, and multi-objective optimization. Thus, the data presented here constitutes the most comprehensive dataset for ML development in over four decades of analog IC design automation. The dataset, ground-truth annotations, and reference implementations of the metric-defining routines are released under an open license, enabling reproducible and directly comparable evaluation across heterogeneous analog design automation methods.

0.65