CS Paper Radar

Interference-Tolerant Mixer-First Receivers for FR3: Design Principles and Tradeoffs

Reza Nikandish, Hamed Rahmani

eess.SP ·submitted 2026-08-23 23:04 UTC · v1

Abstract

Frequency Range 3 (FR3), spanning 7.125-24.25 GHz, is a promising candidate band for 6G communications, bridging the coverage of sub-6 GHz bands and the capacity of millimeter-wave frequencies. Its incumbent-dense and non-contiguous spectrum demands frequency-agile, interference-tolerant receivers (RXs) capable of hopping across fragmented sub-bands while withstanding strong blockers. Mixer-first RXs are well suited to this role, yet their design for FR3 has not been systematically addressed. This paper presents a hardware design perspective on mixer-first RXs for FR3, evaluating selectivity enhancement, harmonic rejection, linearization, low-noise design, and multi-phase clock generation under FR3-specific constraints. The analysis identifies viable techniques, fundamental limitations, and circuit- and architecture-level design tradeoffs. A central insight is that the frequency-translational property of mixer-first RXs allows selectivity, linearization, and noise cancellation to be implemented partly at baseband and translated to RF, enabling frequency-agile FR3 operation while shifting the dominant design constraints to mixer parasitics, baseband circuit robustness, and multi-phase clock generation.

Closest papers

Nearest neighbours by meaning across the whole index.

The Price of the Golden 6G Band: Evaluation of Beam Management Effort in FR3

cs.NI ·2026-09-15 ·Clémence Altmeyerhenzien, Ljiljana Simić, Marina Petrova
published similarity 0.53
Abstract · 6 pages, 10 figures. Accepted for Publication in the IEEE GLOBECOM 2026 Conference

Frequency Range 3 (FR3), 7.125-24.25 GHz, regarded as the "golden band" for 6G networks, has less challenging propagation characteristics than FR2 while offering much wider bandwidth for high data rate applications than FR1. Reusing existing FR1 infrastructure for FR3 network deployments requires gNodeBs (gNBs) to employ antenna arrays and perform beam management, which has proven challenging at FR2. In this paper, we extensively study and characterize the beam management effort in an FR3 urban network, in terms of: beam alignment sensitivity, number of directional link opportunities, gNB handover and beam switch rates, and beam steering distance. Our results show that achieving a high and stable mobile throughput requires significant beam management effort across FR3 bands. While the beam tracking requirements are less stringent at the lower frequencies due to wider beams, the beam switching rate to a non-adjacent beam is relatively comparable at FR3 and FR2.

0.38

Compact Microstrip Triplexer Using Square Open-Loop Resonators with High Isolation for 5G Sub-6 GHz Applications

eess.SP ·2026-08-13 ·Bhaskarareddy N C, Rashmi Ravi, Augustine O. Nwajana
similarity 0.52
Abstract · 6 pages, 1 table, 5 figures

The rapid proliferation of multi-standard 5G New Radio sub-6 GHz systems have intensified the demand for compact, high-isolation multiplexing components capable of simultaneously routing multiple frequency channels through a single shared antenna port without cross-band interference. This paper presents the design and full-wave electromagnetic simulation of a compact microstrip triplexer operating at 2.2, 2.6, and 3.0 GHz for 5G sub-6 GHz applications. The proposed triplexer employs square open-loop resonators arranged as three independent three-pole Chebyshev bandpass filter channels, yielding nine resonator poles in total. Each channel is synthesised from the standard normalised Chebyshev lowpass prototype. The three channels are integrated at a common input port via a T-junction, with connecting transmission line stubs dimensioned to enforce high inter-channel isolation. Full-wave EM simulation results demonstrate return losses of 21.1 dB, 23.1 dB, and 22.8 dB; insertion losses of 1.08 dB, 1.01 dB, and 0.98 dB; and inter-channel isolations of 45.7 dB, 45.2 dB, and 45.7 dB, respectively. The achieved inter-channel isolation exceeding 45 dB represents a significant improvement over the majority of recently reported microstrip triplexer designs.

0.07

A 188-260 GHz Distributed Frequency Multiplier Achieving 4 dBm Saturated Output Power in 65 nm CMOS

eess.SP ·2026-10-03 ·Ahmet Yelboğa, Shuhei Amakawa, Korkut Kaan Tokgöz
similarity 0.52
Abstract · Latin America Microwave Conferance 2026

Sub-terahertz (sub-THz) low-phase-noise signal sources commonly employ frequency multiplier chains to extend the operating frequency of lower-frequency oscillators. This paper presents the design and simulations of a wideband, high-output-power frequency multiplier implemented in TSMC 65 nm CMOS technology. The proposed design is based on a distributed frequency multiplier with a quarter-wave transmission line termination at the drain side, where the reflected and forward-traveling waves are constructively combined to enhance the output power. The proposed frequency doubler achieves a minimum conversion loss of 12 dB at an input frequency of 115 GHz with an input power of 12 dBm, resulting in an output power of 0 dBm and 12.6 dB fundamental suppression. For the same input power, the output power remains within 3 dB of its peak value over the 188-260 GHz output frequency range. At 230 GHz, the proposed design achieves a saturated output power of 4 dBm while occupying an area of 0.149 mm^2.

0.25

Edge-Combining Subharmonic Mixer-First Receiver

eess.SP ·2026-11-17 ·Eric Danson, Jeffrey S. Walling
unusual similarity 0.51
Abstract · 4 pages, 10 figures, 1 Table

A 1-10 GHz subharmonic mixer-first receiver using edge combining to drive N-path switches from 50% duty-cycle clocks at half the local oscillator (LO) frequency avoids the gain penalty of harmonic mixing. Inverter-based differential baseband amplifiers with back-gate feedback linearization set their gain by process-defined capacitance ratios, using no additional components and consuming no additional power. A 22 nm fully depleted silicon on insulator (FD-SOI) prototype receiver achieves a conversion gain of 12.8-18.1 dB and a noise figure of 5.7-11 dB across the band. It achieves up to 15.4 dBm out-of-band IIP3 while consuming 16.7-22.3 mW.

0.31

Rydberg Atomic Quantum Receivers for OFDM Systems: An Atomic-Comb Design

cs.IT physics.atom-phquant-ph ·2026-10-11 ·Yuanbin Chen, Chong Meng Samson See, Chau Yuen
similarity 0.47
Abstract · This manuscript has been submitted to IEEE journal

Rydberg atomic quantum receivers (RAQR) exhibit exceptional sensitivity to radio-frequency (RF) signals, positioning them as promising candidates for next-generation wireless systems. Extending their capabilities to orthogonal frequency-division multiplexing (OFDM), however, requires atomic responses that go beyond broadband reception and are tailored to the structured interference of multicarrier signals. To bridge this gap, we develop an atomic-comb Rydberg receiver based on six-wave mixing (SWM) transduction. In particular, injecting a multi-tone local oscillator (LO) into the RAQR generates frequency-shifted replicas of the intrinsic SWM response. By subtly tuning the amplitude and phase of each LO tone, constructive and destructive interference can be selectively induced to preserve desired response components while attenuating harmful frequency offsets. Furthermore, we harness the response-reshaping capability of the proposed atomic comb to proactively mitigate OFDM interference. More explicitly, by exploiting the discrete difference-frequency structure of both carrier-frequency-offset (CFO)-induced and phase-noise (PN)-induced inter-carrier interference (ICI), we optimize the atomic-comb response to suppress dominant ICI components directly. We further reveal an intrinsic coupling between spectral shaping and the time-domain effective channel memory, motivating a joint optimization of both ICI and inter-symbol interference (ISI), which simultaneously suppresses inter-carrier leakage and post-cyclic-prefix (CP) tail energy. Extensive simulation results validate our atomic-comb design, unveiling that the proposed atomic comb can effectively reshape the receiver response over the OFDM, while mitigating ICI, shortening the effective channel memory, and substantially lowering CP overhead.

0.29

Wideband Microwave Linear Analog Computer (MiLAC) for Frequency-Flat and Frequency-Selective Processing

cs.IT eess.SP ·2026-11-01 ·Juan Vidal Alegría, Matteo Nerini, Bruno Clerckx
similarity 0.47
Abstract · 15 pages, 6 figures. Copyright information may change upon publication at an IEEE journal

Microwave linear analog computer (MiLAC) has been proposed as an analog processing architecture to perform efficient computation in the microwave domain. Consisting of reconfigurable impedance networks, a MiLAC can extract many of the gains of large multi-antenna systems without costly digital processing, e.g., achieving capacity in narrowband multiple-input single-output (MISO). However, the behavior of wideband MiLAC, required to support high data-rate transmissions, is widely unknown. The impedance components of MiLACs have non-trivial frequency-dependent response, requiring specific implementations to characterize it. In this work, we consider MiLAC implementations based on LC resonators with tunable capacitance, which allow synthesizing near-arbitrary passive lossless impedance matrices at individual frequencies using inductors and varactors. We characterize the mapping between optimal MISO precoding at a reference frequency, and the vector of capacitances configuring the MiLAC. We derive the degrees of freedom (DoFs) remaining after fixing such optimum precoding at the reference frequency, and show that these DoFs can be exploited to tune the frequency response of the MiLAC. We propose two techniques to exploit these DoFs: a closed-form approach for frequency-flat MiLAC processing, and a numerical approach for multi-frequency MiLAC processing, optimizing processing at frequencies other than the reference one. The frequency-flat approach shows satisfactory performance in a simulated frequency-flat millimeter-wave scenario, approaching the performance of digital processing. The multi-frequency approach can adapt to the frequency-selectivity of a simulated sub-6GHz scenario, attaining gains over frequency-flat digital processing. This constitutes the first demonstration that realistic MiLAC implementations can be configured to perform independent computations at different frequencies.

0.27

Measurement-Based FR3 Urban Macrocell Channel Characterization and Coverage Analysis

eess.SP ·2026-09-20 ·Enrui Liu, Pan Tang, Haiyang Miao, Qi Zhen, Jianhua Zhang
similarity 0.46
Abstract · 6 pages, 11 figures, conference

The 6--18~GHz upper mid-band is a promising spectrum range for future sixth-generation (6G) networks due to its favorable balance between available bandwidth and propagation capability, while its same-site coverage performance remains a key deployment concern. This paper presents a wideband channel measurement campaign at 13 spatially aligned frequency points from 6 to 18~GHz in an urban macrocell (UMa) environment, and investigates the frequency evolution of channel characteristics and same-site coverage capability. The results show that path loss generally increases with frequency, while the higher-frequency channels tend to exhibit smaller root-mean-square (RMS) delay spread (DS) and larger PDP-based $K$-factors. Based on the measured path-loss characteristics, the additional link-budget requirement and service-aware same-site coverage are further evaluated. Under the baseline service configuration, the 80\% coverage distance $d_{80}$ decreases from approximately 129~m at 6~GHz to 58~m at 18~GHz. Further analysis quantifies the impacts of service rate, resource allocation, interference, and link-budget degradation on coverage, providing measurement-based insights for same-site deployment across the 6--18~GHz band.

0.20

Comparative Analysis and Behavioral Modelling of Power Amplifiers in FR3

eess.SP ·2026-10-14 ·Cel Thys, Rodney Martinez Alonso, Ali H Alsarraf, Zhuangzhuang Cui, Dominique Schreurs +1 more
publishedcode/data similarity 0.45
Abstract · Accepted at 2026 IEEE 1st Annual Integrated Sensing and Communication Conference (ISAC)

Power amplifier (PA) nonlinearity is a critical transmitter impairment in the upper mid-band (7 GHz to 24 GHz), designated as Frequency Range 3 (FR3) in emerging 6G standardisation. The 3GPP PA model baseline, TR 38.803 Annex A, was derived from 2.1 GHz and 28 GHz measurements and has not been revisited yet for FR3 standards work. This paper addresses that gap with characterisation measurements of multiple PA devices-under-test (DUTs), driven into gain compression in the 7 GHz and 15 GHz bands with 100 MHz and 200 MHz bandwidth. Memoryless polynomial and Generalized Memory Polynomial (GMP) behavioral models are extracted by least-squares regression and compared with 3GPP models spanning FR1 and FR2. The GaN PA DUT is modelled best at a higher nonlinear order and shows markedly stronger phase distortion than the wideband PA. The memory terms of the GMP model measurably improve the Normalized Mean Square Error (NMSE) at all operating points. An orthogonal frequency-division multiplexing (OFDM) ambiguity function analysis from the Integrated Sensing and Communication (ISAC) literature, using the extracted models, illustrates how PA compression raises the sidelobe floor of the sensing response. These results provide a reference for PA impairment modelling in FR3, directly applicable to ISAC system design. All model coefficients and measurement data are publicly available [1].

0.40