CS Paper Radar

Compact Microstrip Triplexer Using Square Open-Loop Resonators with High Isolation for 5G Sub-6 GHz Applications

Bhaskarareddy N C, Rashmi Ravi, Augustine O. Nwajana

eess.SP ·submitted 2026-08-13 22:28 UTC · v1

Abstract

The rapid proliferation of multi-standard 5G New Radio sub-6 GHz systems have intensified the demand for compact, high-isolation multiplexing components capable of simultaneously routing multiple frequency channels through a single shared antenna port without cross-band interference. This paper presents the design and full-wave electromagnetic simulation of a compact microstrip triplexer operating at 2.2, 2.6, and 3.0 GHz for 5G sub-6 GHz applications. The proposed triplexer employs square open-loop resonators arranged as three independent three-pole Chebyshev bandpass filter channels, yielding nine resonator poles in total. Each channel is synthesised from the standard normalised Chebyshev lowpass prototype. The three channels are integrated at a common input port via a T-junction, with connecting transmission line stubs dimensioned to enforce high inter-channel isolation. Full-wave EM simulation results demonstrate return losses of 21.1 dB, 23.1 dB, and 22.8 dB; insertion losses of 1.08 dB, 1.01 dB, and 0.98 dB; and inter-channel isolations of 45.7 dB, 45.2 dB, and 45.7 dB, respectively. The achieved inter-channel isolation exceeding 45 dB represents a significant improvement over the majority of recently reported microstrip triplexer designs.

Comment
6 pages, 1 table, 5 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Interference-Tolerant Mixer-First Receivers for FR3: Design Principles and Tradeoffs

eess.SP ·2026-08-23 ·Reza Nikandish, Hamed Rahmani
similarity 0.52
Abstract

Frequency Range 3 (FR3), spanning 7.125-24.25 GHz, is a promising candidate band for 6G communications, bridging the coverage of sub-6 GHz bands and the capacity of millimeter-wave frequencies. Its incumbent-dense and non-contiguous spectrum demands frequency-agile, interference-tolerant receivers (RXs) capable of hopping across fragmented sub-bands while withstanding strong blockers. Mixer-first RXs are well suited to this role, yet their design for FR3 has not been systematically addressed. This paper presents a hardware design perspective on mixer-first RXs for FR3, evaluating selectivity enhancement, harmonic rejection, linearization, low-noise design, and multi-phase clock generation under FR3-specific constraints. The analysis identifies viable techniques, fundamental limitations, and circuit- and architecture-level design tradeoffs. A central insight is that the frequency-translational property of mixer-first RXs allows selectivity, linearization, and noise cancellation to be implemented partly at baseband and translated to RF, enabling frequency-agile FR3 operation while shifting the dominant design constraints to mixer parasitics, baseband circuit robustness, and multi-phase clock generation.

0.24

A 188-260 GHz Distributed Frequency Multiplier Achieving 4 dBm Saturated Output Power in 65 nm CMOS

eess.SP ·2026-10-03 ·Ahmet Yelboğa, Shuhei Amakawa, Korkut Kaan Tokgöz
similarity 0.49
Abstract · Latin America Microwave Conferance 2026

Sub-terahertz (sub-THz) low-phase-noise signal sources commonly employ frequency multiplier chains to extend the operating frequency of lower-frequency oscillators. This paper presents the design and simulations of a wideband, high-output-power frequency multiplier implemented in TSMC 65 nm CMOS technology. The proposed design is based on a distributed frequency multiplier with a quarter-wave transmission line termination at the drain side, where the reflected and forward-traveling waves are constructively combined to enhance the output power. The proposed frequency doubler achieves a minimum conversion loss of 12 dB at an input frequency of 115 GHz with an input power of 12 dBm, resulting in an output power of 0 dBm and 12.6 dB fundamental suppression. For the same input power, the output power remains within 3 dB of its peak value over the 188-260 GHz output frequency range. At 230 GHz, the proposed design achieves a saturated output power of 4 dBm while occupying an area of 0.149 mm^2.

0.25

Energy-Efficient RF Chain Activation for Uplink mmWave Cell-Free Massive MIMO Systems: A Minimum-Cost Maximum-Flow Approach

eess.SP ·2026-10-12 ·Bo Yu, Abdol Hamid Aghvami, Mohammad Shikh-Bahaei
published similarity 0.44
Abstract · Accepted for presentation at 2026 IEEE Globecom Workshops (GC Wkshps)

With the incessant demand for green and sustainable communications, energy efficiency (EE) has become a cornerstone of sixth-generation (6G) network design, especially for cell-free millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems, which can achieve significant throughput gains by leveraging large-scale antenna arrays. Adaptive radio frequency (RF) chain activation (ARFA) is a key technique for reducing power consumption without severely degrading the achievable rate, thereby enhancing the total EE of 6G MIMO systems. In this paper, we propose a minimum-cost maximum-flow (MCMF)-based ARFA scheme to reduce unnecessary power consumption and maximize the total EE of uplink mmWave cell-free massive MIMO systems. Simulation results indicate that the proposed approach can significantly improve the total EE while maintaining a relatively high achievable rate and acceptable computational complexity.

0.30

A Wideband STAR-RIS Employing Shared-Aperture Polarization Conversion and Diagonal Switching Topology for 6G Applications

eess.SP ·2026-10-13 ·Ruiqi Wang, Atif Shamim
similarity 0.42
Abstract

Simultaneously transmitting and reflecting reconfigurable intelligent surfaces (STAR-RIS) enable programmable wave control on both sides of a surface, extending wireless coverage beyond single-sided operation. However, practical STAR-RIS demonstrations in literature have narrow bandwidths, because it is challenging to achieve wideband reflection and transmission simultaneously from the same aperture. To overcome this limitation, a wideband STAR-RIS architecture is proposed based on shared-aperture polarization conversion and diagonal switching topology. Here, multiple resonances enable wideband magnitude responses and mirror-symmetric current reversal maintains $180^{\circ}$ phase difference in both reflection and transmission modes. Accordingly, a diagonal four-branch unit cell configuration is developed, where the tailored top patch directs the received wave either through a pair of blind vias connected by a buried strip to the shared top aperture for reflection, or to the bottom ring patch using a through via for transmission. Based on the proposed design, a 10 by 10 STAR-RIS prototype is fabricated and experimentally characterized. The measured 3-dB bandwidths reach 19.8% in reflection mode and 21.9% in transmission mode. Near-field measurements show average signal enhancements of 19.8 and 22.6 dB for reflection and transmission, respectively, over the wide frequency range of 6.8-8.4 GHz. Far-field measurements further demonstrate average received-power enhancements of 11.2 dB in reflection and 11.9 dB in transmission. To the best of the authors' knowledge, this work presents the first experimentally demonstrated wideband STAR-RIS covering the 7.125-8.4 GHz band within the emerging 6G FR3 spectrum.

0.20

Multi-Band Indoor MIMO Channel Measurements Across Sub-6 GHz, Mid-Band and mmWave: Comparing 2.55 GHz, 12.75 GHz and 25.5 GHz

eess.SP ·2026-11-11 ·Faruk Pasic, Florian Kiss, Florian Asperger, Diego Dupleich, Stefan Schwarz +1 more
published similarity 0.40
Abstract · Submitted to the 21th European Conference on Antennas and Propagation (EuCAP), 2027

Future wireless systems for indoor applications are expected to extend their operating frequencies from sub-6 GHz to mid-band and millimeter wave (mmWave) frequencies to support higher data rates. To characterize the frequency-dependent propagation behavior across these bands, multi-band channel measurements are essential. In this work, we conduct double-directional multiple-input multiple-output (MIMO) channel measurements in an indoor environment to enable a consistent comparison across three frequency bands. Measurements are performed using a 16x16 MIMO configuration at center frequencies of 2.55 GHz, 12.75 GHz and 25.5 GHz, covering both line-of-sight (LOS) and obstructed line-of-sight (OLOS) conditions. The measured channels are processed using the space-alternating generalized expectation maximization (SAGE) algorithm to extract multipath parameters, which are subsequently used to characterize the angular power distributions across the three frequency bands. The results show substantial angular-domain similarity across all three bands in both LOS and OLOS conditions, while also highlighting frequency-dependent variations.

0.31

Noncoherent MIMO in the FR3 Upper Mid-Band Using Grassmannian Signaling: Prototype and Experimental Evaluation

eess.SP math.DG ·2026-10-06 ·Álvaro Pendás-Recondo, Enrique Pendás-Recondo, Álvaro F. Vaquero, Marcos R. Pino, Jesús Alberto López-Fernández
similarity 0.39
Abstract · 13 pages, 9 figures

This work presents a prototype implementation of a noncoherent multiple-input multiple-output (MIMO) system based on Grassmannian signalling, where neither the transmitter nor receiver requires channel state information (CSI), operating at a carrier frequency of 15 GHz in the frequency range 3 (FR3) upper mid-band envisioned for 6G. To the best of our knowledge, this is the first prototype implementation of Grassmannian signaling reported in the literature beyond sub-6 GHz bands. We identify the motivation of applying Grassmannian signaling, a form of unitary space-time modulation (USTM), in this band for wireless and mobile applications with low spectral-efficiency requirements but strict reliability and power-efficiency demands. With this idea in mind, we present a system design integrated with orthogonal frequency-division multiplexing (OFDM) that addresses the challenges associated with the higher carrier frequencies of FR3 while providing reliable operation across a broad range of scenarios, including urban and rural environments as well as vehicular communications. We then present the prototype implementation of the proposed design, based on software-defined radio (SDR) devices integrated with radio-frequency (RF) mixers, filters, and power amplifiers to ensure adequate operation in the targeted band. Over-the-air (OTA) experiments based on symbol error rate (SER) measurements under non-line-of-sight (NLoS) and line-of-sight (LoS) scenarios, and across different data rates, show good agreement with software simulations, thereby validating the prototype implementation.

0.28

Toward Massive MIMO HAPS Networks: Antenna Architectures and Design

eess.SP ·2026-11-18 ·Shasha Liu, Abla Kammoun, Mohamed Slim Alouini
survey similarity 0.39
Abstract · 8 pages, 3 Figures

High-altitude platform stations (HAPS) are expected to become an important component of sixth-generation (6G) and beyond wireless networks by providing wide-area wireless connectivity through massive multiple-input multiple-output (mMIMO) technology. As the communication performance of HAPS systems is fundamentally determined by the antenna array architecture, efficient antenna design has become a critical research topic. Motivated by these considerations, this article provides a comprehensive overview of antenna array design for mMIMO-enabled HAPS systems and proposes two novel antenna architectures to improve antenna-user alignment and communication performance. Specifically, the representative applications of mMIMO-enabled HAPS are first introduced, followed by the key design requirements for HAPS antenna arrays. Representative antenna architectures are then systematically reviewed and compared under a unified simulation framework based on the 3GPP NTN channel model. Finally, several promising research directions are discussed to provide insights into the design of next-generation intelligent HAPS antenna systems.

0.31

Virtualized 5G Tesbed using OpenAirInterface: Tutorial and Benchmarking Tests

cs.NI ·2026-09-11 ·M. Dória, V. Sousa, A. Campos, N. Oliveira, P. Eduardo +7 more
publishedbenchmarkhighly cited similarity 0.39
Abstract

The development of 5G and its evolutionary path to 6G brings virtualization as close as possible to the antennas. Native 3GPP systems are now software running at servers boosted by accelerator cards to cope with computationally intense signal processing. Meanwhile, the Radio Frequency (RF) front-end is still proprietary hardware, sheltering specific PHY-layer procedures like passband amplification/modulation. This approach takes advantage of the software's flexibility while keeping the complex microsecond signal processing performance from modern telecommunication systems. This paper provides tutorial material on the Core Network and Radio Access Network of OpenAirInterface (OAI) 5G stack on top of Universal Software Radio Peripheral (USRP) platforms. A set of blueprints showcases OAI's ability to provide a virtualized 5G network with different transmission capabilities and the possibility to use it with commercial mobile phones. Configuration discussions and throughput benchmark analyses follow installation and deployment instructions. Our results show that 5G prototyping using OAI and USRP frontends can lead to good reproducibility and consistent throughput.

0.49