CS Paper Radar

A 188-260 GHz Distributed Frequency Multiplier Achieving 4 dBm Saturated Output Power in 65 nm CMOS

Ahmet Yelboğa, Shuhei Amakawa, Korkut Kaan Tokgöz

eess.SP ·submitted 2026-10-03 13:23 UTC · v1

Abstract

Sub-terahertz (sub-THz) low-phase-noise signal sources commonly employ frequency multiplier chains to extend the operating frequency of lower-frequency oscillators. This paper presents the design and simulations of a wideband, high-output-power frequency multiplier implemented in TSMC 65 nm CMOS technology. The proposed design is based on a distributed frequency multiplier with a quarter-wave transmission line termination at the drain side, where the reflected and forward-traveling waves are constructively combined to enhance the output power. The proposed frequency doubler achieves a minimum conversion loss of 12 dB at an input frequency of 115 GHz with an input power of 12 dBm, resulting in an output power of 0 dBm and 12.6 dB fundamental suppression. For the same input power, the output power remains within 3 dB of its peak value over the 188-260 GHz output frequency range. At 230 GHz, the proposed design achieves a saturated output power of 4 dBm while occupying an area of 0.149 mm^2.

Comment
Latin America Microwave Conferance 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Interference-Tolerant Mixer-First Receivers for FR3: Design Principles and Tradeoffs

eess.SP ·2026-08-23 ·Reza Nikandish, Hamed Rahmani
similarity 0.52
Abstract

Frequency Range 3 (FR3), spanning 7.125-24.25 GHz, is a promising candidate band for 6G communications, bridging the coverage of sub-6 GHz bands and the capacity of millimeter-wave frequencies. Its incumbent-dense and non-contiguous spectrum demands frequency-agile, interference-tolerant receivers (RXs) capable of hopping across fragmented sub-bands while withstanding strong blockers. Mixer-first RXs are well suited to this role, yet their design for FR3 has not been systematically addressed. This paper presents a hardware design perspective on mixer-first RXs for FR3, evaluating selectivity enhancement, harmonic rejection, linearization, low-noise design, and multi-phase clock generation under FR3-specific constraints. The analysis identifies viable techniques, fundamental limitations, and circuit- and architecture-level design tradeoffs. A central insight is that the frequency-translational property of mixer-first RXs allows selectivity, linearization, and noise cancellation to be implemented partly at baseband and translated to RF, enabling frequency-agile FR3 operation while shifting the dominant design constraints to mixer parasitics, baseband circuit robustness, and multi-phase clock generation.

0.24

An Ultra-Compact Differential V-Band Power Amplifier Using EDMOS Transistors With 18.1 dBm P1dB and 21% PAE in 22nm FD-SOI CMOS

eess.SP eess.SY ·2026-08-25 ·Han Zhou, Torgil Kjellberg, Haojie Chang, Christian Fager
unusual similarity 0.51
Abstract

This paper presents a compact, fully differential, two-stage millimeter-wave (mm-wave) cascode power amplifier (PA) designed and implemented in a 22nm FD-SOI CMOS process (22FDX+). The PA employs the newly introduced extended-drain MOS (EDMOS) device in 22FDX+, together with a carefully engineered device core and transformer baluns. At 50 GHz, the prototype achieves 18.8 dBm saturated output power (PSAT), 18.1 dBm 1-dB compression output power P1dB, and 21% power-added efficiency (PAE) at P1dB. To the best of our knowledge, this work achieves the highest reported power density of 2.6 W/mm2 among single-way, two-stage CMOS cascode PAs.

0.35

Compact Microstrip Triplexer Using Square Open-Loop Resonators with High Isolation for 5G Sub-6 GHz Applications

eess.SP ·2026-08-13 ·Bhaskarareddy N C, Rashmi Ravi, Augustine O. Nwajana
similarity 0.49
Abstract · 6 pages, 1 table, 5 figures

The rapid proliferation of multi-standard 5G New Radio sub-6 GHz systems have intensified the demand for compact, high-isolation multiplexing components capable of simultaneously routing multiple frequency channels through a single shared antenna port without cross-band interference. This paper presents the design and full-wave electromagnetic simulation of a compact microstrip triplexer operating at 2.2, 2.6, and 3.0 GHz for 5G sub-6 GHz applications. The proposed triplexer employs square open-loop resonators arranged as three independent three-pole Chebyshev bandpass filter channels, yielding nine resonator poles in total. Each channel is synthesised from the standard normalised Chebyshev lowpass prototype. The three channels are integrated at a common input port via a T-junction, with connecting transmission line stubs dimensioned to enforce high inter-channel isolation. Full-wave EM simulation results demonstrate return losses of 21.1 dB, 23.1 dB, and 22.8 dB; insertion losses of 1.08 dB, 1.01 dB, and 0.98 dB; and inter-channel isolations of 45.7 dB, 45.2 dB, and 45.7 dB, respectively. The achieved inter-channel isolation exceeding 45 dB represents a significant improvement over the majority of recently reported microstrip triplexer designs.

0.07

Edge-Combining Subharmonic Mixer-First Receiver

eess.SP ·2026-11-17 ·Eric Danson, Jeffrey S. Walling
unusual similarity 0.46
Abstract · 4 pages, 10 figures, 1 Table

A 1-10 GHz subharmonic mixer-first receiver using edge combining to drive N-path switches from 50% duty-cycle clocks at half the local oscillator (LO) frequency avoids the gain penalty of harmonic mixing. Inverter-based differential baseband amplifiers with back-gate feedback linearization set their gain by process-defined capacitance ratios, using no additional components and consuming no additional power. A 22 nm fully depleted silicon on insulator (FD-SOI) prototype receiver achieves a conversion gain of 12.8-18.1 dB and a noise figure of 5.7-11 dB across the band. It achieves up to 15.4 dBm out-of-band IIP3 while consuming 16.7-22.3 mW.

0.31

Realistic modeling of Photonic Terahertz Communication based on a real-world 30 km 30 Gbps experimental demonstration

eess.SP ·2026-09-26 ·Mingxu Wang, Jianjun Yu, Xianming Zhao, Jiali Chen, Ye Zhou +7 more
publishedbenchmark similarity 0.46
Abstract · 15 pages, 10 figures

Experimental studies have demonstrated that THz links can support multi-kilometer, gigabit-per-second wireless transmission. However, few studies have effectively validated channel models through high-capacity, long-distance experiments. In this work, we experimentally demonstrate a 30 km ultra-long-haul photonic THz wireless communication system. 16 Gbaud quadrature phase shift keying (QPSK) signals are transmitted and tested, achieving a maximum data rate of 30 Gbps. For the first time, we validate two widely used THz channel models using a fully implemented 30 km experimental setup, providing a systematic and thorough analysis that integrates theoretical modeling with experimental results. We also perform an analysis of power consumption in photonic THz communication systems and provide a detailed comparison between simulated and experimental power consumption results. Finally, a detailed performance comparison between the simulation and experimental results, including signal-to-noise ratio (SNR), bit error rate (BER) and data rate, are provided. Our work provides essential insights for the design and energy-efficient deployment of future high-capacity THz networks, establishing a benchmark for subsequent research in channel modeling, experimental verification, and system-level energy efficiency.

0.34

An Efficient W-/D-Band Power Amplifier in a 130 nm SiGe BiCMOS Process

eess.SP eess.SY ·2026-08-25 ·Han Zhou, Yu Yan, Haojie Chang, Herbert Zirath
unusual similarity 0.46
Abstract

This paper presents a wideband power amplifier (PA) designed and implemented in Infineon Technologies' 130-nm SiGe BiCMOS process for upper W-band and lower D-band applications. A complete load-pull simulation methodology is carried out, and a band pass filter (BPF)-based matching strategy is employed for the design of the output and inter-stage matching networks. The fabricated PA prototype achieves a small-signal gain 3-dB bandwidth of 71-133 GHz. Moreover, it maintains a relatively flat gain of approximately 15.7 dB over 75-128 GHz, with less than 1-dB fluctuation. The measured saturated output power is 8.8-11.7 dBm, while the measured peak power-added efficiency (PAE) is 7.2-11.1%. These results demonstrate the potential of SiGe BiCMOS technology for wideband and integrated transmitter front ends operating across the W-/D-band frequency range.

0.35

Wideband Microwave Linear Analog Computer (MiLAC) for Frequency-Flat and Frequency-Selective Processing

cs.IT eess.SP ·2026-11-01 ·Juan Vidal Alegría, Matteo Nerini, Bruno Clerckx
similarity 0.44
Abstract · 15 pages, 6 figures. Copyright information may change upon publication at an IEEE journal

Microwave linear analog computer (MiLAC) has been proposed as an analog processing architecture to perform efficient computation in the microwave domain. Consisting of reconfigurable impedance networks, a MiLAC can extract many of the gains of large multi-antenna systems without costly digital processing, e.g., achieving capacity in narrowband multiple-input single-output (MISO). However, the behavior of wideband MiLAC, required to support high data-rate transmissions, is widely unknown. The impedance components of MiLACs have non-trivial frequency-dependent response, requiring specific implementations to characterize it. In this work, we consider MiLAC implementations based on LC resonators with tunable capacitance, which allow synthesizing near-arbitrary passive lossless impedance matrices at individual frequencies using inductors and varactors. We characterize the mapping between optimal MISO precoding at a reference frequency, and the vector of capacitances configuring the MiLAC. We derive the degrees of freedom (DoFs) remaining after fixing such optimum precoding at the reference frequency, and show that these DoFs can be exploited to tune the frequency response of the MiLAC. We propose two techniques to exploit these DoFs: a closed-form approach for frequency-flat MiLAC processing, and a numerical approach for multi-frequency MiLAC processing, optimizing processing at frequencies other than the reference one. The frequency-flat approach shows satisfactory performance in a simulated frequency-flat millimeter-wave scenario, approaching the performance of digital processing. The multi-frequency approach can adapt to the frequency-selectivity of a simulated sub-6GHz scenario, attaining gains over frequency-flat digital processing. This constitutes the first demonstration that realistic MiLAC implementations can be configured to perform independent computations at different frequencies.

0.27

A Wideband STAR-RIS Employing Shared-Aperture Polarization Conversion and Diagonal Switching Topology for 6G Applications

eess.SP ·2026-10-13 ·Ruiqi Wang, Atif Shamim
similarity 0.44
Abstract

Simultaneously transmitting and reflecting reconfigurable intelligent surfaces (STAR-RIS) enable programmable wave control on both sides of a surface, extending wireless coverage beyond single-sided operation. However, practical STAR-RIS demonstrations in literature have narrow bandwidths, because it is challenging to achieve wideband reflection and transmission simultaneously from the same aperture. To overcome this limitation, a wideband STAR-RIS architecture is proposed based on shared-aperture polarization conversion and diagonal switching topology. Here, multiple resonances enable wideband magnitude responses and mirror-symmetric current reversal maintains $180^{\circ}$ phase difference in both reflection and transmission modes. Accordingly, a diagonal four-branch unit cell configuration is developed, where the tailored top patch directs the received wave either through a pair of blind vias connected by a buried strip to the shared top aperture for reflection, or to the bottom ring patch using a through via for transmission. Based on the proposed design, a 10 by 10 STAR-RIS prototype is fabricated and experimentally characterized. The measured 3-dB bandwidths reach 19.8% in reflection mode and 21.9% in transmission mode. Near-field measurements show average signal enhancements of 19.8 and 22.6 dB for reflection and transmission, respectively, over the wide frequency range of 6.8-8.4 GHz. Far-field measurements further demonstrate average received-power enhancements of 11.2 dB in reflection and 11.9 dB in transmission. To the best of the authors' knowledge, this work presents the first experimentally demonstrated wideband STAR-RIS covering the 7.125-8.4 GHz band within the emerging 6G FR3 spectrum.

0.20