CS Paper Radar

An Efficient W-/D-Band Power Amplifier in a 130 nm SiGe BiCMOS Process

Han Zhou, Yu Yan, Haojie Chang, Herbert Zirath

eess.SP eess.SY ·submitted 2026-08-25 15:16 UTC · v1
unusual

Abstract

This paper presents a wideband power amplifier (PA) designed and implemented in Infineon Technologies' 130-nm SiGe BiCMOS process for upper W-band and lower D-band applications. A complete load-pull simulation methodology is carried out, and a band pass filter (BPF)-based matching strategy is employed for the design of the output and inter-stage matching networks. The fabricated PA prototype achieves a small-signal gain 3-dB bandwidth of 71-133 GHz. Moreover, it maintains a relatively flat gain of approximately 15.7 dB over 75-128 GHz, with less than 1-dB fluctuation. The measured saturated output power is 8.8-11.7 dBm, while the measured peak power-added efficiency (PAE) is 7.2-11.1%. These results demonstrate the potential of SiGe BiCMOS technology for wideband and integrated transmitter front ends operating across the W-/D-band frequency range.

Closest papers

Nearest neighbours by meaning across the whole index.

An Ultra-Compact Differential V-Band Power Amplifier Using EDMOS Transistors With 18.1 dBm P1dB and 21% PAE in 22nm FD-SOI CMOS

eess.SP eess.SY ·2026-08-25 ·Han Zhou, Torgil Kjellberg, Haojie Chang, Christian Fager
unusual similarity 0.58
Abstract

This paper presents a compact, fully differential, two-stage millimeter-wave (mm-wave) cascode power amplifier (PA) designed and implemented in a 22nm FD-SOI CMOS process (22FDX+). The PA employs the newly introduced extended-drain MOS (EDMOS) device in 22FDX+, together with a carefully engineered device core and transformer baluns. At 50 GHz, the prototype achieves 18.8 dBm saturated output power (PSAT), 18.1 dBm 1-dB compression output power P1dB, and 21% power-added efficiency (PAE) at P1dB. To the best of our knowledge, this work achieves the highest reported power density of 2.6 W/mm2 among single-way, two-stage CMOS cascode PAs.

0.35

Edge-Combining Subharmonic Mixer-First Receiver

eess.SP ·2026-11-17 ·Eric Danson, Jeffrey S. Walling
unusual similarity 0.52
Abstract · 4 pages, 10 figures, 1 Table

A 1-10 GHz subharmonic mixer-first receiver using edge combining to drive N-path switches from 50% duty-cycle clocks at half the local oscillator (LO) frequency avoids the gain penalty of harmonic mixing. Inverter-based differential baseband amplifiers with back-gate feedback linearization set their gain by process-defined capacitance ratios, using no additional components and consuming no additional power. A 22 nm fully depleted silicon on insulator (FD-SOI) prototype receiver achieves a conversion gain of 12.8-18.1 dB and a noise figure of 5.7-11 dB across the band. It achieves up to 15.4 dBm out-of-band IIP3 while consuming 16.7-22.3 mW.

0.31

A 188-260 GHz Distributed Frequency Multiplier Achieving 4 dBm Saturated Output Power in 65 nm CMOS

eess.SP ·2026-10-03 ·Ahmet Yelboğa, Shuhei Amakawa, Korkut Kaan Tokgöz
similarity 0.46
Abstract · Latin America Microwave Conferance 2026

Sub-terahertz (sub-THz) low-phase-noise signal sources commonly employ frequency multiplier chains to extend the operating frequency of lower-frequency oscillators. This paper presents the design and simulations of a wideband, high-output-power frequency multiplier implemented in TSMC 65 nm CMOS technology. The proposed design is based on a distributed frequency multiplier with a quarter-wave transmission line termination at the drain side, where the reflected and forward-traveling waves are constructively combined to enhance the output power. The proposed frequency doubler achieves a minimum conversion loss of 12 dB at an input frequency of 115 GHz with an input power of 12 dBm, resulting in an output power of 0 dBm and 12.6 dB fundamental suppression. For the same input power, the output power remains within 3 dB of its peak value over the 188-260 GHz output frequency range. At 230 GHz, the proposed design achieves a saturated output power of 4 dBm while occupying an area of 0.149 mm^2.

0.25

Comparative Analysis and Behavioral Modelling of Power Amplifiers in FR3

eess.SP ·2026-10-14 ·Cel Thys, Rodney Martinez Alonso, Ali H Alsarraf, Zhuangzhuang Cui, Dominique Schreurs +1 more
publishedcode/data similarity 0.44
Abstract · Accepted at 2026 IEEE 1st Annual Integrated Sensing and Communication Conference (ISAC)

Power amplifier (PA) nonlinearity is a critical transmitter impairment in the upper mid-band (7 GHz to 24 GHz), designated as Frequency Range 3 (FR3) in emerging 6G standardisation. The 3GPP PA model baseline, TR 38.803 Annex A, was derived from 2.1 GHz and 28 GHz measurements and has not been revisited yet for FR3 standards work. This paper addresses that gap with characterisation measurements of multiple PA devices-under-test (DUTs), driven into gain compression in the 7 GHz and 15 GHz bands with 100 MHz and 200 MHz bandwidth. Memoryless polynomial and Generalized Memory Polynomial (GMP) behavioral models are extracted by least-squares regression and compared with 3GPP models spanning FR1 and FR2. The GaN PA DUT is modelled best at a higher nonlinear order and shows markedly stronger phase distortion than the wideband PA. The memory terms of the GMP model measurably improve the Normalized Mean Square Error (NMSE) at all operating points. An orthogonal frequency-division multiplexing (OFDM) ambiguity function analysis from the Integrated Sensing and Communication (ISAC) literature, using the extracted models, illustrates how PA compression raises the sidelobe floor of the sensing response. These results provide a reference for PA impairment modelling in FR3, directly applicable to ISAC system design. All model coefficients and measurement data are publicly available [1].

0.40

TACS-RF: Tool-driven Agentic Circuit Synthesis of RF and mmWave Modules

cs.AI ·2026-10-22 ·Tristan Liang, Aravind Nagulu
published similarity 0.44
Abstract · Accepted for presentation at the 2027 IEEE Radio and Wireless Week (RWW), Silicon Monolithic Integrated Circuits in RF Systems (SiRF)

We present the framework of TACS-RF - a Tool-driven Agentic Circuit Synthesis of RF and mmWave modules. In this framework, a large-language-model (LLM) coding agent (Claude Opus 4.8) directly drives industry-standard electronic-design-automation (EDA) tools such as Cadence Virtuoso/Spectre, Calibre, Cadence EMX, and Ansys HFSS to design RF and mmWave modules. We validate the framework through the agentic design of a 240-251 GHz sub-THz transmitter in a 90 nm SiGe BiCMOS process. The agent semi-autonomously designed the sub-blocks including a 60 GHz push-push Colpitts VCO with second-harmonic extraction, multistage differential cascode power drivers, a push-push frequency doubler, a differential bowtie antenna, and all the interstage matching networks. The transmitter chain with parasitic-extracted devices and EM-verified passives delivers +5.1 to +6.3 dBm across an 11 GHz varactor-only tuning range, phase noise of -80 to -88 dBc/Hz at 1 MHz offset while consuming a DC power of 361 mW. We describe the agent-driven design flow and the resulting division of labor between human and agent, taking a step toward a "text-to-ASIC" future for designing RF/mmWave hardware.

0.32

Implementation and Validation of Mismatch-Tolerant High-Gain OTA with a Calibrated Negative Conductance Load

eess.SP ·2026-10-29 ·Mayank Aggarwal, Naveen Kadayinti
similarity 0.42
Abstract · 6 pages, 13 figures

This paper presents the circuit-level implementation of a mismatch-tolerant high-gain operational transconductance amplifier (OTA) using automatic negative-conductance calibration in 65-nm CMOS. The technique enhances OTA gain by compensating for its finite output conductance using a cross-coupled transistor pair, with an on-chip calibration loop that eliminates the need for a replica circuit or external tuning. The calibration routine increases the gain by driving the steady state error of the OTA in a unity gain feedback loop toward zero. The implementation addresses practical challenges involving comparator offset, DAC design, and subtractor gain and offset. A 6-bit capacitive DAC (CDAC)-based comparator offset calibration scheme enables reliable detection of the sub-millivolt steady state error required for high OTA gain. Post-layout Monte Carlo simulations show that the comparator offset standard deviation is reduced from 4.11 mV to 132 $μ$V, with a maximum observed post-calibration offset of 625 $μ$V. The complete calibration circuitry is implemented and evaluated through post-layout simulations.

0.32

Towards Energy-Neutral IoT Sensors: Low-Cost Chirp-Based Backscattering Node Using a COTS Microcontroller and Multi-Load Front-End

eess.SP ·2026-09-23 ·Tijl Schepens, Liesbet Van der Perre, Gilles Callebaut
similarity 0.38
Abstract

Backscatter communication has proven to be a key enabler for energy-neutral sensor nodes in the IoT. It allows ultra-low-power nodes to transmit sensor data by reflecting incident RF signals. Practical large-scale deployment requires hardware solutions that are both cost-efficient and widely available. This paper investigates the practical limits of implementing backscatter transmitters exclusively using COTS components. We compare a two-load and multi-load architecture in terms of hardware requirements, complexity and spectral efficiency highlighting the most important trade-offs. A multi-load backscatter architecture is developed using a resource constrained low-power microcontroller, levering DMA to achieve high switching speeds while minimizing processing overhead. Furthermore, we present a layout agnostic load design methodology based on scattering parameters, allowing precise control of the reflection coefficients. A prototype implementation demonstrates a successful backscatter transmission of a single-sideband chirp with reduced harmonic distortion. Measurement results show suppression of the backscattered carrier and the second sideband by 10 dBm. This demonstrates that low-cost sensor nodes can be built using COTS components enabling remote monitoring at extended lifetimes.

0.23

Interference-Tolerant Mixer-First Receivers for FR3: Design Principles and Tradeoffs

eess.SP ·2026-08-23 ·Reza Nikandish, Hamed Rahmani
similarity 0.38
Abstract

Frequency Range 3 (FR3), spanning 7.125-24.25 GHz, is a promising candidate band for 6G communications, bridging the coverage of sub-6 GHz bands and the capacity of millimeter-wave frequencies. Its incumbent-dense and non-contiguous spectrum demands frequency-agile, interference-tolerant receivers (RXs) capable of hopping across fragmented sub-bands while withstanding strong blockers. Mixer-first RXs are well suited to this role, yet their design for FR3 has not been systematically addressed. This paper presents a hardware design perspective on mixer-first RXs for FR3, evaluating selectivity enhancement, harmonic rejection, linearization, low-noise design, and multi-phase clock generation under FR3-specific constraints. The analysis identifies viable techniques, fundamental limitations, and circuit- and architecture-level design tradeoffs. A central insight is that the frequency-translational property of mixer-first RXs allows selectivity, linearization, and noise cancellation to be implemented partly at baseband and translated to RF, enabling frequency-agile FR3 operation while shifting the dominant design constraints to mixer parasitics, baseband circuit robustness, and multi-phase clock generation.

0.24