CS Paper Radar

Edge-Combining Subharmonic Mixer-First Receiver

Eric Danson, Jeffrey S. Walling

eess.SP ·submitted 2026-11-17 10:19 UTC · v1
unusual

Abstract

A 1-10 GHz subharmonic mixer-first receiver using edge combining to drive N-path switches from 50% duty-cycle clocks at half the local oscillator (LO) frequency avoids the gain penalty of harmonic mixing. Inverter-based differential baseband amplifiers with back-gate feedback linearization set their gain by process-defined capacitance ratios, using no additional components and consuming no additional power. A 22 nm fully depleted silicon on insulator (FD-SOI) prototype receiver achieves a conversion gain of 12.8-18.1 dB and a noise figure of 5.7-11 dB across the band. It achieves up to 15.4 dBm out-of-band IIP3 while consuming 16.7-22.3 mW.

Comment
4 pages, 10 figures, 1 Table

Closest papers

Nearest neighbours by meaning across the whole index.

An Efficient W-/D-Band Power Amplifier in a 130 nm SiGe BiCMOS Process

eess.SP eess.SY ·2026-08-25 ·Han Zhou, Yu Yan, Haojie Chang, Herbert Zirath
unusual similarity 0.52
Abstract

This paper presents a wideband power amplifier (PA) designed and implemented in Infineon Technologies' 130-nm SiGe BiCMOS process for upper W-band and lower D-band applications. A complete load-pull simulation methodology is carried out, and a band pass filter (BPF)-based matching strategy is employed for the design of the output and inter-stage matching networks. The fabricated PA prototype achieves a small-signal gain 3-dB bandwidth of 71-133 GHz. Moreover, it maintains a relatively flat gain of approximately 15.7 dB over 75-128 GHz, with less than 1-dB fluctuation. The measured saturated output power is 8.8-11.7 dBm, while the measured peak power-added efficiency (PAE) is 7.2-11.1%. These results demonstrate the potential of SiGe BiCMOS technology for wideband and integrated transmitter front ends operating across the W-/D-band frequency range.

0.35

Interference-Tolerant Mixer-First Receivers for FR3: Design Principles and Tradeoffs

eess.SP ·2026-08-23 ·Reza Nikandish, Hamed Rahmani
similarity 0.51
Abstract

Frequency Range 3 (FR3), spanning 7.125-24.25 GHz, is a promising candidate band for 6G communications, bridging the coverage of sub-6 GHz bands and the capacity of millimeter-wave frequencies. Its incumbent-dense and non-contiguous spectrum demands frequency-agile, interference-tolerant receivers (RXs) capable of hopping across fragmented sub-bands while withstanding strong blockers. Mixer-first RXs are well suited to this role, yet their design for FR3 has not been systematically addressed. This paper presents a hardware design perspective on mixer-first RXs for FR3, evaluating selectivity enhancement, harmonic rejection, linearization, low-noise design, and multi-phase clock generation under FR3-specific constraints. The analysis identifies viable techniques, fundamental limitations, and circuit- and architecture-level design tradeoffs. A central insight is that the frequency-translational property of mixer-first RXs allows selectivity, linearization, and noise cancellation to be implemented partly at baseband and translated to RF, enabling frequency-agile FR3 operation while shifting the dominant design constraints to mixer parasitics, baseband circuit robustness, and multi-phase clock generation.

0.24

An Ultra-Compact Differential V-Band Power Amplifier Using EDMOS Transistors With 18.1 dBm P1dB and 21% PAE in 22nm FD-SOI CMOS

eess.SP eess.SY ·2026-08-25 ·Han Zhou, Torgil Kjellberg, Haojie Chang, Christian Fager
unusual similarity 0.50
Abstract

This paper presents a compact, fully differential, two-stage millimeter-wave (mm-wave) cascode power amplifier (PA) designed and implemented in a 22nm FD-SOI CMOS process (22FDX+). The PA employs the newly introduced extended-drain MOS (EDMOS) device in 22FDX+, together with a carefully engineered device core and transformer baluns. At 50 GHz, the prototype achieves 18.8 dBm saturated output power (PSAT), 18.1 dBm 1-dB compression output power P1dB, and 21% power-added efficiency (PAE) at P1dB. To the best of our knowledge, this work achieves the highest reported power density of 2.6 W/mm2 among single-way, two-stage CMOS cascode PAs.

0.35

The Analytical Investigation of Inductor-Coupled Mixers

cs.AR ·2026-10-24 ·Arash Ghasemi
unusual similarity 0.48
Abstract · 32 pages, 7 figures. Data and code: https://doi.org/10.5281/zenodo.23608384

Inductor- and transformer-coupled balanced mixers are usually analyzed with switching approximations, conversion matrices, harmonic balance, or circuit simulation. This paper instead derives their loaded quasistatic equations from the device laws, keeping the transformer ratios, reflected load, bias, and the connections that set the IF common mode. The functions needed to solve these equations are surprisingly varied. A Shockley single-balanced pair is solved by the principal Lambert function $W_0$ under a quantified one-diode-dominance condition. The double-balanced ring has a unique loaded solution that reduces to an exact inverse-hyperbolic-tangent form only for an open IF port. Vacuum diodes and triodes lead to Cardano cubics and structured sextics, whereas depletion JFET/MESFET crossbars need only square roots. Bilateral MOS channels give piecewise quadratics in strong inversion, or a Ferrari quartic when the IF winding floats. In weak inversion they give an exact $W_0$, the real $r$-Lambert function, or the inverse of $\sinh x+ρx$, depending on topology and IF connection. In matched BJT and HBT Gilbert cells, equal emitter resistors turn the hyperbolic-tangent current steering into an exact $r$-Lambert function. Fourier projection brings in Beta/Gamma, modified Bessel, and complete elliptic functions. We checked the equations against 37 LTspice simulations using seven independent Python programs. In the 12 primary comparisons, which implement the assumed device laws exactly, every RMS waveform error was below 0.017% of the analytical RMS value; built-in and vendor device models were examined separately. Two design examples show how the closed forms size a thermionic IF load and a Gilbert-cell tail current without parameter sweeps.

0.40

Compute Before You Digitize: ADC-less Mixed-Signal Processing for Scalable Cryogenic Qubit Readout

cs.AR quant-phcs.ETeess.SP ·2026-11-17 ·Qirui Zhang, Ben Toby, He Wang, Benjamin Lienhard, David Blaauw +1 more
similarity 0.47
Abstract

We introduce DIRAC, an ADC-less in-cryostat qubit readout architecture that uses analog computing to redraw the analog-digital boundary. Directly operating on the front-end's analog output, passive complex mixers perform the equivalent of digital demodulation, ping-pong active-RC integrators average their outputs into down-sampled per-qubit traces, and a time-domain stage digitizes them, eliminating Nyquist-rate ADCs. A TX-RX co-design derives the mixers' local oscillators from the readout transmitter's baseband rather than per-tone PLLs. A per-line calibration flow trains the matched filter jointly with the neural network, improving fidelity and enabling low-bit-width, low-voltage digital processing. Designed in 22 nm FD-SOI and evaluated at 4 K on 1.12M experimental shots, DIRAC matches the fidelity of a floating-point (FP32) digital pipeline for readout windows down to 750 ns, at 31.6$\times$ and 238$\times$ lower energy than the fixed-point (FxP) and FP32 pipelines. It cuts the total 4 K power per physical qubit by 50.4% and 68.6% relative to FxP and room-temperature flex cables, respectively. At a fixed logical-qubit count and 4 K budget, this yields, against FxP, a code distance larger by 2 to 6 and a 1.6-7.3$\times$ (Willow) and 4.9-204$\times$ (SI1000, $p = 10^{-3}$) lower logical error rate.

0.22

A 188-260 GHz Distributed Frequency Multiplier Achieving 4 dBm Saturated Output Power in 65 nm CMOS

eess.SP ·2026-10-03 ·Ahmet Yelboğa, Shuhei Amakawa, Korkut Kaan Tokgöz
similarity 0.46
Abstract · Latin America Microwave Conferance 2026

Sub-terahertz (sub-THz) low-phase-noise signal sources commonly employ frequency multiplier chains to extend the operating frequency of lower-frequency oscillators. This paper presents the design and simulations of a wideband, high-output-power frequency multiplier implemented in TSMC 65 nm CMOS technology. The proposed design is based on a distributed frequency multiplier with a quarter-wave transmission line termination at the drain side, where the reflected and forward-traveling waves are constructively combined to enhance the output power. The proposed frequency doubler achieves a minimum conversion loss of 12 dB at an input frequency of 115 GHz with an input power of 12 dBm, resulting in an output power of 0 dBm and 12.6 dB fundamental suppression. For the same input power, the output power remains within 3 dB of its peak value over the 188-260 GHz output frequency range. At 230 GHz, the proposed design achieves a saturated output power of 4 dBm while occupying an area of 0.149 mm^2.

0.25

Wideband Hybrid Beamforming via Programmable Unitary Mixer--TTD RF Networks

eess.SP ·2026-11-15 ·Nikola Zlatanov, Damir Salakhov, Zhen Gao
published similarity 0.44
Abstract · Accepted

This paper proposes a wideband hybrid beamforming architecture whose analog front-end consists of fixed unitary mixers interlaced with programmable diagonal phase-shift/true-time-delay (TTD) layers. Under ideal passive-component assumptions, the analog beamformer is semi-unitary on every OFDM subcarrier, so the injected RF-chain power reaches the antenna ports without analog-network loss. We design the phase shifts and delays of the programmable diagonal phase-shift/TTD layers for OFDM sum-rate maximization. Numerical results show that increasing mixer--TTD depth improves the sum rate under ideal component assumptions and a common injected RF-power budget. With component losses included, a shallow design retains an advantage over the evaluated hybrid baselines at low-to-moderate powers, motivating deeper implementations with low accumulated loss.

0.33

An Ultra-Low-Noise Tunable TIA in 45nm Silicon Photonics for Electro-Optical Ultrasound Data Acquisition

eess.SP eess.SY ·2026-11-06 ·Marziyeh Rezaei, Sridhar Singhal, Alp A. Derin, Soner Sonmezoglu, Sajjad Moazeni
unusual similarity 0.43
Abstract

This paper presents the design and experimental characterization of a 32-channel, WDM-compatible electronic-photonic receiver array fabricated in the GlobalFoundries 45nm monolithic silicon photonics process. Optimized for miniaturized, millimeter-scale electro-optical ultrasound data acquisition probes for broadband photo-acoustic imaging (PAI), the chip utilizes integrated micro-ring resonator (MRR) demultiplexers and photodiode (PD) arrays to decode multi-wavelength acoustic signals outside the body. This work focuses specifically on the comprehensive characterization of the receiver front-end, evaluating both the optical WDM filter bank and the transimpedance amplifier (TIA) performance. Monolithic co-integration minimizes critical photodiode-to-TIA interface parasitics. The TIA incorporates a DC-offset cancellation loop that compensates for photodiode-induced offset currents while providing tunable low-frequency cutoff control over a range of 30 kHz to 1.5 MHz. This tunability enables effective suppression of flicker noise and improves overall signal integrity. The front-end achieves the peak transimpedance gain of 144 dB$Ω$ while maintaining an ultra-low input-referred noise current density of $1\text{ pA}/\sqrt{\text{Hz}}$, demonstrating a highly scalable architecture for high-sensitivity intravascular and endobronchial imaging.

0.29