CS Paper Radar

The Analytical Investigation of Inductor-Coupled Mixers

Arash Ghasemi

cs.AR ·submitted 2026-10-24 03:39 UTC · v1
unusual

Abstract

Inductor- and transformer-coupled balanced mixers are usually analyzed with switching approximations, conversion matrices, harmonic balance, or circuit simulation. This paper instead derives their loaded quasistatic equations from the device laws, keeping the transformer ratios, reflected load, bias, and the connections that set the IF common mode. The functions needed to solve these equations are surprisingly varied. A Shockley single-balanced pair is solved by the principal Lambert function $W_0$ under a quantified one-diode-dominance condition. The double-balanced ring has a unique loaded solution that reduces to an exact inverse-hyperbolic-tangent form only for an open IF port. Vacuum diodes and triodes lead to Cardano cubics and structured sextics, whereas depletion JFET/MESFET crossbars need only square roots. Bilateral MOS channels give piecewise quadratics in strong inversion, or a Ferrari quartic when the IF winding floats. In weak inversion they give an exact $W_0$, the real $r$-Lambert function, or the inverse of $\sinh x+ρx$, depending on topology and IF connection. In matched BJT and HBT Gilbert cells, equal emitter resistors turn the hyperbolic-tangent current steering into an exact $r$-Lambert function. Fourier projection brings in Beta/Gamma, modified Bessel, and complete elliptic functions. We checked the equations against 37 LTspice simulations using seven independent Python programs. In the 12 primary comparisons, which implement the assumed device laws exactly, every RMS waveform error was below 0.017% of the analytical RMS value; built-in and vendor device models were examined separately. Two design examples show how the closed forms size a thermionic IF load and a Gilbert-cell tail current without parameter sweeps.

Comment
32 pages, 7 figures. Data and code: https://doi.org/10.5281/zenodo.23608384

Closest papers

Nearest neighbours by meaning across the whole index.

Edge-Combining Subharmonic Mixer-First Receiver

eess.SP ·2026-11-17 ·Eric Danson, Jeffrey S. Walling
unusual similarity 0.48
Abstract · 4 pages, 10 figures, 1 Table

A 1-10 GHz subharmonic mixer-first receiver using edge combining to drive N-path switches from 50% duty-cycle clocks at half the local oscillator (LO) frequency avoids the gain penalty of harmonic mixing. Inverter-based differential baseband amplifiers with back-gate feedback linearization set their gain by process-defined capacitance ratios, using no additional components and consuming no additional power. A 22 nm fully depleted silicon on insulator (FD-SOI) prototype receiver achieves a conversion gain of 12.8-18.1 dB and a noise figure of 5.7-11 dB across the band. It achieves up to 15.4 dBm out-of-band IIP3 while consuming 16.7-22.3 mW.

0.31

Equivalent DQ Sequence-Domain Model of Unbalanced Three-Phase Passive Elements for Power Converter Controllers

eess.SY ·2026-09-01 ·Air\án Franc\és, Luis Saz, Rafael Castillo, Dionisio Ramirez, Javier Uceda
publishedtheoryhighly cited similarity 0.47
Abstract · 8 pages, 7 figures, 2023 IEEE Applied Power Electronics Conference and Exposition (APEC)

Equivalent dq0 models of three-phase passive impedances are widely used for the design of three-phase inverter and rectifier controllers in the synchronous frame. However, these equivalent models assume that the impedance in each phase are the same, which is not always applicable. The fact that the impedance in each phase is different, generates second order harmonic content in the dq0 components, which hinders the advantages of the dq0 transformation. To avoid the second harmonic in these scenarios, it is possible to use the Fortescue's theorem to represent any asymmetrical set of three-phase signals as a linear combination of three symmetrical sequences. In the literature, only a few works have attempted to derive the equivalent model of unbalanced three-phase passive elements in the sequence domain, and none is able to account for the interaction between the zero sequence and the positive and negative sequences. This work presents the derivation of the equivalent dq sequence-domain model of unbalanced three-phase passive elements both analytically and with an intuitive graphical approach. Experimental results are shown to validate the proposed models.

0.73

Time Invariance, Circle Symmetry, and the Completeness of the Cardiff Behavioral Model

eess.SP ·2026-09-22 ·Nicholas B. Tufillaro
theoryunusual similarity 0.43
Abstract · 10 pages, 4 figures, 5 tables. v3: one sentence in Sec. VIII corrected (the multi-harmonic extension uses the single circle, not a torus); r…

Frequency-domain behavioral models of nonlinear microwave devices (the Cardiff model, X-parameters, higher-order sinusoidal describing functions, and the baseband models of power-amplifier predistortion) share one functional form, and each modeling framework justifies the form by its own argument, time invariance among them. Here we give the mathematical argument by which time invariance alone determines the model form, and state the result as a theorem for two-port devices, with its extension to any number of ports. Under a shift of the time origin each harmonic phasor rotates by a multiple of the fundamental's angle, so the spectral map of a time-invariant device is equivariant under a weighted circle action, and classical invariant theory gives its general form. The result is a completeness theorem for the form already in use: every time-invariant two-port response in single-tone periodic steady state is a phase factor attached to the fundamental multiplying a function of the wave magnitudes and their relative phase. The Cardiff exponents become counters: $m$ is the order of the load-side nonlinearity, $n$ is set by the drive-side harmonic, and $r$ is the number of conjugate pairs. The bound $r_{\max}=\lfloor K/2\rfloor$ for a load-side nonlinearity of degree $K$ makes the familiar restriction $r\le1$ a hypothesis about the device, exact for a cubic nonlinearity; for a loaded device the bound becomes a measurable decay in $r$. The results are illustrated with a published measurement and two simulations.

0.52

Symmetry and the Form of Nonlinear Behavioral Models: A Tutorial for Microwave Engineers

eess.SP ·2026-10-01 ·Nicholas B. Tufillaro
similarity 0.42
Abstract · 25 pages, 7 figures, 4 tables. v3: one sentence in the Scope section corrected (multi-harmonic and multi-port cases use the single circle; o…

Behavioral models of nonlinear microwave devices -- the Cardiff model, X-parameters, the higher-order describing functions of the mechanical-systems literature -- all share a functional form. This tutorial derives that form from time invariance alone. It develops the consequences of that derivation using only the harmonic-balance description of a single-tone periodic steady state, in which each port waveform is a finite set of harmonic phasors, and uses them to give the Cardiff model's three exponents physical interpretations. In the monomial rewriting the magnitude exponent $m$ is the order of the device's load-side nonlinearity; the phase exponent $n$ is set by the drive-side harmonic; and the conjugate index $r$ obeys $r_{\max}=\lfloor K/2\rfloor$, where $K$ is the degree of the load-side nonlinearity. The familiar restriction $r\le1$ is therefore a statement about the device, exact whenever $K\le3$. The final sections show that a tailored A-pull measurement displays this decomposition directly: each spectral cluster's half-width is the order of the nonlinearity that produced it. The tutorial is pedagogical and is meant as a gentler introduction to the results treated in the companion paper "Time invariance, circle symmetry, and the completeness of the Cardiff behavioral model", which states and proves the theorems in full.

0.35

Mutual-Coupling-Aware Movable and Fluid Antennas on Holographic Surfaces: A Wavenumber-Domain Circuit-Field Unification

eess.SP ·2026-09-04 ·Giovanni Iacovelli, Chandan Kumar Sheemar, Symeon Chatzinotas
similarity 0.42
Abstract

Movable and fluid antenna systems turn antenna position into a design variable. At sub-wavelength spacings, however, their behavior is governed by mutual coupling, modeled today by two disjoint traditions: circuit-theoretic impedance matrices with element-level constants, and field-theoretic kernels with norm-type power constraints. This paper unifies the two. Starting from the impedance kernel of a holographic surface, a Poynting-anchored balance identifies its resistive part with ohmic plus radiated power and its reactive part with stored-energy imbalance, and a circuit-field equivalence shows that the multiport impedance matrix is the kernel sampled at the port separations, in a single closed spherical-Hankel form. In the wavenumber domain the resistive kernel asymptotically diagonalizes in the aperture size: visible modes radiate at closed-form prices, evanescent modes only dissipate, and a flexible port becomes a constant-modulus codeword whose coupling is the pullback of the spectral weight. Coupling-aware multi-user sum-rate maximization over precoders and port positions is then formulated under physical power and voltage constraints and solved by weighted-MMSE and projected-gradient steps with closed-form gradients. A modal relaxation upper-bounds every port configuration and seeds the search by FFT-based codeword projection. A half-wavelength corollary and a superdirectivity margin quantify when coupling hurts, and when it helps.

0.44

Passive ladder-network representation of the radiation impedance of a spherical cap on a rigid sphere

eess.AS physics.class-ph ·2026-11-10 ·Ronald M. Aarts
unusual similarity 0.42
Abstract · 13 pages (preprint format), 3 figures. Submitted to JASA Express Letters

A loudspeaker in a closed box is modeled as a rigid sphere with an axially moving cap. For an axisymmetric cone-velocity profile, its radiation impedance is written as a network. Each spherical-harmonic mode has an impedance rational in frequency, realized exactly as a finite passive ladder of masses and compliances terminated in a resistance. Ideal transformers set by Legendre coefficients couple these ladders; truncated modes reduce to a residual mass. Despite the different geometry, the impedance resembles that of a baffled piston but, at equal volume velocity, has half its low-frequency resistance and about three quarters of its radiation mass.

0.27

Fast simulation of nonlinear deep resistive networks for energy-based computation

cs.ET ·2026-09-07 ·Filip Osana, Julie Grollier, Damien Querlioz
similarity 0.40
Abstract

Deep resistive networks are electronic energy-based systems in which computation is performed by the steady-state voltages of nonlinear circuits. Nonlinear devices enable expressive input-output transformations, but make the circuit equilibria costly to compute during simulation and training. Recent coordinate-descent solvers have achieved large speedups over SPICE-class circuit simulators, but only for nonlinearities modeled as ideal-diode models. This mathematical simplification is not sufficient for practical analog circuits. Here we extend coordinate-descent simulation to realistic monotone nonlinearities, including Shockley diodes, antiparallel diode pairs, and piecewise-linear current-voltage characteristics. With neighboring voltages fixed, each node update remains a scalar Kirchhoff-law solve. Single-exponential characteristics admit closed-form Lambert-(W) updates, while more general monotone characteristics can be handled with scalar root-finding methods. Across networks with one to three hidden layers and hidden widths from 64 to 1024, the solver reproduces matched SPICE steady-state voltages with relative $L_1$ errors below $1.1\times10^{-4}$ for 90% of validation samples, while achieving speedups up to $(1.7\times10^3)$. We further train a $1568\times100\times20$ double-Shockley network on MNIST, reaching about 3.0% test error and reducing the per-epoch training time by roughly $4.4\times10^2$. Together, these results establish a practical route to the circuit-level design and training of large-scale analog energy-based systems incorporating realistic nonlinear devices.

0.27

Phase-Compensated Frequency-Scan Measurement of Harmonic Transfer Function Impedance

eess.SY ·2026-10-28 ·Yiyang Liao, Yitong Li, Jinjun Liu
similarity 0.39
Abstract

Impedance models obtained through frequency scanning provides terminal characterization for small-signal stability analysis without requiring detailed knowledge of internal converter parameters. When unbalanced steady-state components introduce cross-frequency coupling, conventional $2\times2$ impedance scan methods must be extended to identify harmonic transfer function (HTF) impedance. However, the measured phases of frequency-coupling terms depend on the starting time of the fast Fourier transform (FFT) window, potentially introducing phase errors when different time references are used. This paper presents a $dq$-domain measurement method of HTF impedance that explicitly accounts for this time dependence. Phase compensation aligns the measured Fourier coefficients to a common electrical phase reference, correcting the resulting phase discrepancies and enabling consistent impedance reconstruction. Comparisons with analytical models under balanced and unbalanced conditions verify the measurement method, recovering the conventional $2\times2$ impedance and the dominant coupling blocks of a $6\times6$ HTF representation, respectively.

0.34