CS Paper Radar

A high-isolation wideband channelizer for MKID readouts: a custom HLS implementation on RFSoC

Alberto Hernandez Fernandez, David Diaz Martin, Jose Javier Diaz Garcia, Roger John Hoyland, Luis Fernando Rodriguez Ramos, Diego Portero Rodriguez, Silvestre Rodriguez Perez

eess.SP astro-ph.IM ·submitted 2026-08-25 12:08 UTC · v1
publishedbenchmark

Abstract

We present a high-performance channelizer for Microwave Kinetic Inductance Detectors (MKIDs), designed to mitigate spectral leakage and scalloping loss through a 50% overlapping polyphase filter bank (PFB). The design is implemented on a Xilinx Zynq UltraScale+ RFSoC ZCU111 using a custom design - primarily in Vitis High-Level Synthesis (HLS), with the time-critical output serializer and glue logic in VHDL - that processes a 4.096 GSPS input stream with a per-branch super-sample rate (SSR) of 16. Rather than relying on aggressive 512 MHz clocking and vendor IP cores, our split-path architecture computes the delayed and non-delayed polyphase branches concurrently, so that the bulk of the channelizer operates at a robust 256 MHz while a single 512 MHz subdomain is confined to the BRAM-to-FFT section. This architectural parallelism enables a deep 16-tap prototype filter that doubles the filter depth of comparable high-speed systems and substantially improves channel isolation. We report the complete internal architecture of the reordering engine that implements the overlap, including two implementation hazards not documented in prior art: a pipeline-stage skew affecting state toggles in HLS, and the state-preservation requirements of a restartable design. The 2/1 overlapped channel response is validated in simulation - recovering the ~3.9 dB scalloping loss of a critically sampled channelizer to below 0.1 dB across the full 2 MHz channel - and characterized systematically with a 100-tone batch frequency sweep, while the parent readout system has been operated cryogenically with an MKID array in an adiabatic demagnetization refrigerator (ADR), identifying individual resonators in total darkness. The result is a resource-efficient, high-isolation benchmark for wideband frequency-division-multiplexed readouts.

Comment
18 pages, 7 figures. Submitted to the Journal of Astronomical Telescopes, Instruments, and Systems (JATIS). Extended version of Proc. SPIE 14156, paper 14156-102. Also available at engrXiv: doi:10.31224/7763

Closest papers

Nearest neighbours by meaning across the whole index.

FIREQ: FPGA Instrumentation for Readout and Qubit control

eess.SY quant-ph ·2026-08-29 ·Giuseppe La Capra, Fabio Calabrese, Giorgio D'Amico, Christian Conti, Andrea De Simone +6 more
code/data similarity 0.62
Abstract · 15 pages, 9 figures

We present FIREQ (FPGA Instrumentation for Readout and Qubit control), an open-source RFSoC-based framework for the control and readout of superconducting qubits. FIREQ combines a modular AXI-compliant firmware architecture with a PYNQ-based software stack designed to support extensible hardware integration, deterministic experiment timing, and low-overhead execution of repeated calibration and characterization workflows. The firmware implements direct RF synthesis and acquisition, trigger-based sequencing, programmable pulse generation, frequency-multiplexed readout, and memory-efficient acquisition and waveform buffering. The software adopts a client-server architecture with streamed data transfer and dependency-aware configuration updates to reduce host-device and reconfiguration overhead during parameter sweeps. On an AMD Zynq UltraScale+ RFSoC ZCU216, FIREQ generates RF pulses up to 9.3 GHz with a pulse-duration resolution of 107 ps and an event-timing resolution of 1.7 ns. FPGA resource utilization is compared with representative open-source RFSoC control frameworks, showing a low BRAM footprint while retaining full-rate I/Q generation and acquisition. The RF output is characterized in terms of phase noise, noise spectral density, and inter-channel timing skew. End-to-end operation is validated on a superconducting qubit through resonator spectroscopy, Rabi, Ramsey, and relaxation measurements, yielding T1 = 6.94 us and T2* = 13.50 us. FIREQ can therefore be used both as a qubit-control platform and as an experimental environment for evaluating alternative control and readout IP architectures.

0.35

xCHEM: SDR-Based Multi-Link Channel Emulator for Real-Time Hardware-in-the-Loop Digital-Twin

eess.SP ·2026-10-28 ·Ali Saeizadeh, Gabriele Gemmi, Tamerlan Aghayev, Michele Polese, Pedram Johari +1 more
similarity 0.59
Abstract · 13 pages, 16 figures, 4 tables

This paper presents xCHEM, a radio-frequency channel emulator that inserts programmable channels between physical radios using a single NI USRP X4xx software-defined radio. External channel models stream impulse responses to its field-programmable gate array without firmware changes or interruption of signal processing. A streaming datapath implements six independently configurable directional channels across four radio interfaces. Each channel uses a sparse finite impulse response filter whose memory-backed delays decouple delay span from multiplier resources. The real and complex variants support 32 and 16 nonzero taps, respectively, with a maximum delay of 16666.62 ns and 4.069 ns resolution. Coefficient scaling and arithmetic right shifts control attenuation. Hardware measurements show root-mean-square errors of 9.5 ps in delay over the full span and 0.11 dB in attenuation. Multipath delays are recovered within one sample. An FPGA coefficient engine produces tested Doppler shifts from +/-1 Hz to +/-1 MHz with mean frequency errors below 0.032 Hz relative to quantized commands after carrier-offset calibration; at 200 Hz, it reduces the measured near-carrier spur by 53.3 dB compared with 1 kHz host updates.

0.39

uhd-rfsoc: Bringing Off-the-Shelf RFSoC Boards to Unmodified UHD Applications

cs.NI cs.AReess.SP ·2026-11-13 ·Wei Cheng, Yiming Li, Junyao Zheng, Cheng-Bin Chen, Tingjun Chen
code/data similarity 0.57
Abstract

Next-generation wireless research relies on software-defined radios (SDRs) with more channels and larger bandwidth. The USRP family is one of the most widely used SDR platforms, and much of the wireless software ecosystem is built on top of the USRP hardware driver (UHD). However, each USRP model comes with a fixed channel count, bandwidth, and streaming capability. Off-the-shelf radio frequency system-on-chip (RFSoC) boards, on the other hand, integrate up to 16 analog-to-digital converters (ADCs) and 16 digital-to-analog converters (DACs) operating at several gigasamples per second (GS/s), but existing UHD applications cannot directly use them. We present uhd-rfsoc, an open-source FPGA design and host software stack that turns these boards, including the 16-channel ZCU216 and the RFSoC 4x2, into standard UHD devices without modifying UHD. Through standard UHD calls, applications can configure the carrier frequency, channel count, the per-channel I/Q sample rate, and the wire format. uhd-rfsoc combines timestamped, flow-controlled sample transport in the FPGA with data plane development kit (DPDK) packet processing and vectorized sample conversion on x86 and Arm hosts. The built bitstreams for a number of RFSoC board configurations with varying RF data converter rates, channel counts, I/Q sample rates, and wire formats all successfully pass UHD's built-in streaming benchmarks. We further demonstrate compatibility with unmodified GNU Radio flowgraphs, a custom GPU-accelerated transceiver digital signal processing pipeline, as well as the OCUDU and Duranta 5G radio access network stacks using both software and commodity user equipment.

0.35

Exploring and optimizing the Vivado Flow on large FPGA designs: A Practical Analysis of Strategies and Their Impact on Timing

cs.AR eess.SPhep-ex ·2026-10-28 ·Kachkachi Nor Eddine
similarity 0.55
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

Achieving timing closure in FPGA designs is crucial, especially for high-performance applications. The Vivado Design Suite offers several strategies for optimization, but finding the best configuration for a given project remains challenging. This paper explores the various Vivado's timing directives and strategies to improve performance across timing, area, and runtime. Through two test-case designs, an NQR spectrometer SoC-FPGA and a digital readout ASIC prototype for high energy physics particle detector's, different strategies and configurations are compared to identify the most efficient flow.

0.34

Minimum RISC-V: Maximum FPGA Efficiency

cs.AR ·2026-10-15 ·Martin Langhammer, Bogdan Pasca, Gregg Baeckler
published similarity 0.53
Abstract

RISC-V processors are now widely available for FPGAs, with most FPGA vendors replacing their proprietary soft-CPU architectures with this instruction-set architecture (ISA). Although contemporary FPGAs are increasingly resource- and feature-rich, a soft processor system---including memory---often occupies a disproportionately large footprint and delivers only modest performance relative to the potential of the target device. In this work we first design a lightweight but deeply pipelined RISC-V core that can run above 700 MHz in a mid-range device and that is capable of retiring one instruction per clock under ideal conditions. We then develop and demonstrate a new optimization method that compiles the final application binary and a specialized processor instance contemporaneously. The method expands each instruction into an application-specific encoding, removes unused datapath and decode logic during synthesis, and yields cores that remain assembler-compatible with the original program while no longer being binary-compatible with a general-purpose RISC-V. We implement example designs on RV32I (base integer), RV32M (integer multiply), and RV32F (single-precision floating-point) configurations. Our optimized RISC-V is as small as 170 ALMs and closes timing at 775 MHz in an Altera Agilex-5 device. Finally, we show that these processors can be packed into a deterministic area and stepped-and-repeated continuously without material impact on performance, enabling predictable multi-core density planning.

0.35

Randomized Caches in Hardware: Challenges and Trade-offs

cs.AR cs.CR ·2026-10-30 ·Xinrui Wang, Pascal Kosak, Christof Paar, Daniel Genkin, Yuval Yarom +1 more
similarity 0.52
Abstract

Randomized caches protect against side-channel attacks by obfuscating the mapping of memory addresses to cache locations. Existing proposals typically describe architectural behavior, leaving practical hardware implementation challenges largely unexplored. We implement four prominent designs, CEASER-S, ScatterCache, SassCache, and MIRAGE, and integrate them as the last-level cache (LLC) of a multi-core out-of-order RISC-V system-on-chip (SoC). We identify common and design-specific implementation challenges and develop practical solutions. We evaluate complete FPGA implementations by running SPEC CPU 2017 rate and GAPBS workloads to completion, providing, to our knowledge, the first comparative evaluation of these designs on a common full-system hardware platform. Pipelining the index derivation function (IDF) alone is insufficient: in three of the four variants, other components become the frequency bottleneck, reducing frequency by up to 35% relative to the baseline set-associative cache. Redesigning the critical paths while preserving mappings, rekeying, and victim-selection policies brings the three affected variants to no more than 10% below the baseline frequency, at the cost of added latency or reduced concurrency. Increased LLC access latency, rather than additional misses, dominates IPC degradation, reducing instructions per cycle by up to 5% for SPEC and 11% for GAPBS. Hardware overhead depends on the design and implementation technology: FPGA lookup-table usage increases by 10-35%, while ASIC area increases by 1-14%.

0.22

Chimera: A Configurable LLM Decode Accelerator Architecture with Compute-Memory-Floorplan Co-Design for HBM-Equipped Multi-Die FPGAs

cs.AR ·2026-11-14 ·Zhiheng Chen, Yifan Zhang, Yu-An Chou, Ye Qiao, Sitao Huang
benchmark similarity 0.52
Abstract

GPUs are widely used for LLM inference, but single-request decoding is memory-bound, leaving their compute underutilized while they draw substantial power. HBM-equipped FPGAs are well suited to LLM decoding: their customizable datapaths use memory bandwidth more energy-efficiently than GPUs. However, high memory bandwidth alone does not ensure high decode performance: exploiting it requires parallel compute and memory interfaces, whose resource costs and placement on the chip can limit the throughput. We present Chimera, a configurable LLM decode accelerator architecture that co-designs compute, memory access, and floorplan. Specifically, HBM Proxy Ports extend HBM access to compute lanes on every super logic region (SLR) die, and tiered expert storage holds mixture-of-experts weights beyond the HBM capacity. In addition, a unified configuration analysis estimates per-token latency and per-SLR resource use and guides the design of each configuration within resource budgets. On an AMD Alveo U280, we build ten designs for eight dense, mixture-of-experts, hybrid linear/standard-attention, and ternary LLMs, up to an 80B-parameter mixture-of-experts LLM on four memory tiers. Chimera's designs achieve a geometric mean of 1.6$\times$ the token throughput of prior state-of-the-art FPGA implementations and 3.0$\times$ and 1.5$\times$ the energy efficiency of the RTX 3090 and A100 GPUs, setting a new benchmark for LLM decoding on HBM-equipped FPGAs.

0.23

An Interleaved Parallel Dependent Quantization Hardware Architecture for H.266/VVC

cs.AR ·2026-10-07 ·Jun Zhang, Weizhi Bian, Hao Zhang
similarity 0.52
Abstract

While dependent quantization in H.266/VVC delivers a high compression ratio, its strong serial nature and high complexity result in poor real-time performance, making it difficult to deploy in practical scenarios. To improve the real-time performance of dependent quantization with minimal degradation to its compression performance, we propose a interleaved parallel dependent quantization hardware architecture with low BDBR loss, which achieves four-channel parallel dependent quantization by time-division multiplexing most combinational logic. This architecture adopts the proposed intra-CG context simplification scheme and the encoding scheme that skips decAbslevel during rate estimation. The proposed design incurs a BDBR loss of only 0.42% under the All Intra configuration and 0.38% under the Random Access configuration, respectively. Implemented in Verilog HDL, the dependent quantization hardware architecture achieves quantization speeds of 4K@33.2, 91.4, 331.2, and 454.1 fps at QP = 22, 27, 32, and 37, respectively, when implemented on the Xilinx XCZU19 FPGA. When implemented on ASIC using the TSMC 28nm process standard cell library, the corresponding quantization speeds reach 4K@84.0, 231.0, 837.0, and 1147.7 fps.

0.13