CS Paper Radar

xCHEM: SDR-Based Multi-Link Channel Emulator for Real-Time Hardware-in-the-Loop Digital-Twin

Ali Saeizadeh, Gabriele Gemmi, Tamerlan Aghayev, Michele Polese, Pedram Johari, Tommaso Melodia

eess.SP ·submitted 2026-10-28 20:40 UTC · v1

Abstract

This paper presents xCHEM, a radio-frequency channel emulator that inserts programmable channels between physical radios using a single NI USRP X4xx software-defined radio. External channel models stream impulse responses to its field-programmable gate array without firmware changes or interruption of signal processing. A streaming datapath implements six independently configurable directional channels across four radio interfaces. Each channel uses a sparse finite impulse response filter whose memory-backed delays decouple delay span from multiplier resources. The real and complex variants support 32 and 16 nonzero taps, respectively, with a maximum delay of 16666.62 ns and 4.069 ns resolution. Coefficient scaling and arithmetic right shifts control attenuation. Hardware measurements show root-mean-square errors of 9.5 ps in delay over the full span and 0.11 dB in attenuation. Multipath delays are recovered within one sample. An FPGA coefficient engine produces tested Doppler shifts from +/-1 Hz to +/-1 MHz with mean frequency errors below 0.032 Hz relative to quantized commands after carrier-offset calibration; at 200 Hz, it reduces the measured near-carrier spur by 53.3 dB compared with 1 kHz host updates.

Comment
13 pages, 16 figures, 4 tables

Closest papers

Nearest neighbours by meaning across the whole index.

A high-isolation wideband channelizer for MKID readouts: a custom HLS implementation on RFSoC

eess.SP astro-ph.IM ·2026-08-25 ·Alberto Hernandez Fernandez, David Diaz Martin, Jose Javier Diaz Garcia, Roger John Hoyland, Luis Fernando Rodriguez Ramos +2 more
publishedbenchmark similarity 0.59
Abstract · 18 pages, 7 figures. Submitted to the Journal of Astronomical Telescopes, Instruments, and Systems (JATIS). Extended version of Proc. SPIE 1…

We present a high-performance channelizer for Microwave Kinetic Inductance Detectors (MKIDs), designed to mitigate spectral leakage and scalloping loss through a 50% overlapping polyphase filter bank (PFB). The design is implemented on a Xilinx Zynq UltraScale+ RFSoC ZCU111 using a custom design - primarily in Vitis High-Level Synthesis (HLS), with the time-critical output serializer and glue logic in VHDL - that processes a 4.096 GSPS input stream with a per-branch super-sample rate (SSR) of 16. Rather than relying on aggressive 512 MHz clocking and vendor IP cores, our split-path architecture computes the delayed and non-delayed polyphase branches concurrently, so that the bulk of the channelizer operates at a robust 256 MHz while a single 512 MHz subdomain is confined to the BRAM-to-FFT section. This architectural parallelism enables a deep 16-tap prototype filter that doubles the filter depth of comparable high-speed systems and substantially improves channel isolation. We report the complete internal architecture of the reordering engine that implements the overlap, including two implementation hazards not documented in prior art: a pipeline-stage skew affecting state toggles in HLS, and the state-preservation requirements of a restartable design. The 2/1 overlapped channel response is validated in simulation - recovering the ~3.9 dB scalloping loss of a critically sampled channelizer to below 0.1 dB across the full 2 MHz channel - and characterized systematically with a 100-tone batch frequency sweep, while the parent readout system has been operated cryogenically with an MKID array in an adiabatic demagnetization refrigerator (ADR), identifying individual resonators in total darkness. The result is a resource-efficient, high-isolation benchmark for wideband frequency-division-multiplexed readouts.

0.48

MIRAGE: A GPU-Accelerated IQ-Level Channel Emulator for Real-Time Wireless Digital Twins

cs.NI eess.SP ·2026-10-28 ·Ali Saeizadeh, Angelo Feraudo, Avaneeth Anil, Leonardo Bonati, Pedram Johari +1 more
similarity 0.59
Abstract · 14 pages, 12 figures, 3 tables

Wireless digital twins enable network policies to be evaluated before deployment, but reproducing channel effects within a running protocol stack requires continuous waveform processing under strict timing constraints. We present MIRAGE, a GPU-accelerated channel emulator that applies propagation effects directly to in-phase and quadrature samples exchanged by software 5G New Radio stacks. MIRAGE combines batched multiuser, multiantenna filtering with timestamped shared-memory transport and radio-driver integrations for OpenAirInterface and OCUDU. External propagation models supply channel responses asynchronously, while versioned buffers ensure consistent coefficients within each processing interval. Experiments on one NVIDIA H100 GPU evaluate waveform accuracy, processing time, channel updates, and full-stack traffic delivery. At 61.44 million samples per second, eight single-antenna links, four two-by-two links, and one four-by-four link meet the tested 0.5 ms bidirectional processing criterion. Waveform errors remain within one integer quantization step per component, with no mixed coefficient versions across 16.7 million analyzed slots. Integration with the X5G testbed enables slice resource allocations to be evaluated before deployment. Both evaluated slices ultimately satisfy their throughput caps, requiring one physical reconfiguration under line-of-sight conditions and four under non-line-of-sight conditions. These results demonstrate full-stack policy evaluation and expose prediction errors affecting transfer to a physical network.

0.37

uhd-rfsoc: Bringing Off-the-Shelf RFSoC Boards to Unmodified UHD Applications

cs.NI cs.AReess.SP ·2026-11-13 ·Wei Cheng, Yiming Li, Junyao Zheng, Cheng-Bin Chen, Tingjun Chen
code/data similarity 0.58
Abstract

Next-generation wireless research relies on software-defined radios (SDRs) with more channels and larger bandwidth. The USRP family is one of the most widely used SDR platforms, and much of the wireless software ecosystem is built on top of the USRP hardware driver (UHD). However, each USRP model comes with a fixed channel count, bandwidth, and streaming capability. Off-the-shelf radio frequency system-on-chip (RFSoC) boards, on the other hand, integrate up to 16 analog-to-digital converters (ADCs) and 16 digital-to-analog converters (DACs) operating at several gigasamples per second (GS/s), but existing UHD applications cannot directly use them. We present uhd-rfsoc, an open-source FPGA design and host software stack that turns these boards, including the 16-channel ZCU216 and the RFSoC 4x2, into standard UHD devices without modifying UHD. Through standard UHD calls, applications can configure the carrier frequency, channel count, the per-channel I/Q sample rate, and the wire format. uhd-rfsoc combines timestamped, flow-controlled sample transport in the FPGA with data plane development kit (DPDK) packet processing and vectorized sample conversion on x86 and Arm hosts. The built bitstreams for a number of RFSoC board configurations with varying RF data converter rates, channel counts, I/Q sample rates, and wire formats all successfully pass UHD's built-in streaming benchmarks. We further demonstrate compatibility with unmodified GNU Radio flowgraphs, a custom GPU-accelerated transceiver digital signal processing pipeline, as well as the OCUDU and Duranta 5G radio access network stacks using both software and commodity user equipment.

0.35

A Four-Branch Radar Target Simulator with Fractional Delay on a PlutoSDR

eess.SP ·2026-11-11 ·Florian Euchner, Stephan ten Brink
code/data similarity 0.55
Abstract

Repeatable test setups support the development and evaluation of integrated sensing and communications (ISAC) hardware and algorithms. Commercial radar target simulators are expensive, while sub-6 GHz ISAC experiments often need only tens of megahertz of bandwidth within their available spectrum allocation. This makes simpler, low-cost test hardware attractive. We present a low-cost, open-source radar target simulator based on an ADALM-Pluto without hardware modification, supporting four independently configurable targets and analog bandwidths up to 56 MHz. The FPGA generates echoes with independent delays, Doppler shifts and gains, using fractional-delay filters for sub-sample adjustment. For motion-consistent echoes, delay and carrier phase are updated together to reproduce both changing range and frequency-dependent Doppler shifts. Over-the-air measurements demonstrate simultaneous echoes, sub-sample delay adjustment, and smooth target motion between sample positions. The FPGA source, firmware and on-device web interface are publicly available.

0.38

Channel Estimation for OFDM via Delay-Doppler Refinement

cs.IT ·2026-09-09 ·Mingcheng Nie, Hao Chang, Xiaoqi Zhang, Junkai Liu, Wibowo Hardjawana +2 more
similarity 0.53
Abstract

In this paper, we propose a novel channel estimation (CE) algorithm for orthogonal frequency division multiplexing (OFDM) systems that exploits the unique characteristics of the delay-Doppler (DD) domain channel. Specifically, the time-frequency (TF) domain input-output relationship (IOR) is derived in a compact form by focusing solely on the non-zero elements of the TF domain channel matrix. Based on this compact IOR, a coarse TF domain CE is first performed using a linear minimum mean square error estimator. Then, the resultant TF domain estimates are transformed to the DD domain through a unitary transformation for further refinement. We reveal that the effective DD domain channel matrix can be viewed as an aggregation of multiple DD domain channel responses with different phase shifts. This allows us to devise a threshold-based estimation for DD domain channel parameters with high accuracy. The estimated DD domain channel parameters are then applied to form a refined estimate of TF domain channel. Our numerical results demonstrate that the proposed method can achieve substantial performance gains over conventional OFDM channel estimation techniques under the same pilot deployment.

0.25

An Interleaved Parallel Dependent Quantization Hardware Architecture for H.266/VVC

cs.AR ·2026-10-07 ·Jun Zhang, Weizhi Bian, Hao Zhang
similarity 0.53
Abstract

While dependent quantization in H.266/VVC delivers a high compression ratio, its strong serial nature and high complexity result in poor real-time performance, making it difficult to deploy in practical scenarios. To improve the real-time performance of dependent quantization with minimal degradation to its compression performance, we propose a interleaved parallel dependent quantization hardware architecture with low BDBR loss, which achieves four-channel parallel dependent quantization by time-division multiplexing most combinational logic. This architecture adopts the proposed intra-CG context simplification scheme and the encoding scheme that skips decAbslevel during rate estimation. The proposed design incurs a BDBR loss of only 0.42% under the All Intra configuration and 0.38% under the Random Access configuration, respectively. Implemented in Verilog HDL, the dependent quantization hardware architecture achieves quantization speeds of 4K@33.2, 91.4, 331.2, and 454.1 fps at QP = 22, 27, 32, and 37, respectively, when implemented on the Xilinx XCZU19 FPGA. When implemented on ASIC using the TSMC 28nm process standard cell library, the corresponding quantization speeds reach 4K@84.0, 231.0, 837.0, and 1147.7 fps.

0.13

AFDM Channel Parameter Estimation: Exploiting its Shift Properties and Input-Output Relationship

eess.SP ·2026-10-08 ·Jialiang Zhu, Zeping Sui, Zilong Liu, Arman Farhang
hot direction similarity 0.53
Abstract

Affine frequency division multiplexing (AFDM) has attracted significant attention owing to its excellent backwards compatibility, full diversity achievability, as well as strong resilience to high Doppler and various hardware impairments. Existing AFDM channel parameter estimation methods, however, either require large pilot overhead or rely on computationally intensive grid search methods. This paper proposes a grid-search-independent, low-overhead, impulse-pilot-based channel parameter estimation method for AFDM systems by exploiting its inherent shift properties. Specifically, we show that the effect of a Doppler shift on the impulse pilot is equivalent to a delay shift in the time domain with a phase rotation. Additionally, both delay and Doppler shifts lead to cyclic shifts in the affine domain. By utilizing these properties in both the time and affine domains, two linear equations are formed to estimate the integer delay and Doppler of each path. The fractional part of the Doppler is estimated from the Doppler-induced leakage around the impulse pilot by exploiting the AFDM input-output relationship. For multipath channels, a successive interference cancellation (SIC) framework is developed, in which the strongest propagation path is first estimated, reconstructed, and canceled before the remaining paths are successively estimated. Simulation results demonstrate that the proposed method significantly reduces computational complexity and allows lower pilot overhead than the benchmarks. The proposed method also achieves improved channel parameter estimation and

0.26

A Parallel Two-Stage Prony Framework for Robust Delay-Doppler Estimation

eess.SP ·2026-10-28 ·Liangchen Sun, Yutaka Jitsumatsu
similarity 0.52
Abstract

This paper addresses off-grid physical delay-Doppler parameter estimation based on an orthogonal time frequency space (OTFS) pilot waveform over doubly selective channels. Based on a known single-pilot waveform with a frequency-shifted sinc pulse structure, we propose a parallel dual-order estimation framework, in which Prony-based Doppler-first and delay-first procedures are executed concurrently and their candidate paths are jointly fused. The two estimation orders provide complementary resolution characteristics, thereby mitigating ambiguities caused by closely spaced multipath components and fractional delay--Doppler mismatch. Numerical results show that the proposed framework improves detection reliability and estimation stability compared with a single-order Prony estimator, especially in off-grid scenarios and low-to-moderate signal-to-noise ratio regimes.

0.26