CS Paper Radar

Extending Ground-Constraint LiDAR-IMU Calibration to Tilted Surfaces in a Continuous-Time Framework

Vassili Korotkine, Pierre Chamoun, Mohammed Ayman Shalaby, James Richard Forbes

cs.RO ·submitted 2026-08-25 20:35 UTC · v1
code/data

Abstract

This paper presents a novel method that extends targetless LiDAR-IMU calibration for ground vehicles to non- flat environments. Calibration typically necessitates full exci- tation of the sensor rig, a requirement that is not fulfilled by ground vehicles in normal operation. To address the degenerate planar motion, state-of-the-art methods propose residuals that assume the colinearity of the gravity and physical surface normal vectors, restricting usage to cases where the ground is assumed flat. This paper proposes ground-plane residuals that do not require this assumption, and are applicable for planar motion on a tilted surface. Results are demonstrated on a dataset collected from a Husky ground vehicle, on the M2DGR dataset, as well as on an offroad vehicle dataset. Repeatability is shown to be improved both in tilted and flat-ground scenarios, with strong improvement demonstrated for the tilted case. The implementation and experiments are open-sourced at https://github.com/vkorotkine/licalib_tilted_ground.

Comment
8 pages, 13 figures. Submitted to Robotics & Automation Letters

Closest papers

Nearest neighbours by meaning across the whole index.

VeriCalib: Verifiable Target-Based LiDAR-Camera Calibration

cs.RO ·2026-10-20 ·Xiangcheng Hu, Xieyuanli Chen, Feiyi Chen, Shengli Ren, Shiyang Chen +6 more
similarity 0.71
Abstract · 35 pages, 20 figures, 13 tables

Target-based extrinsic calibration estimates the rigid transform between sensors from a few observations of a known target, and its result is commonly assessed by the root-mean-square error of the fitted residuals. However, this scalar error is computed on the same observations and therefore cannot indicate whether to accept the result, re-extract, recollect or add observations. This paper presents VeriCalib, which formulates extrinsic calibration as a verifiable estimation problem and reports a calibration state. The key insight is a two-level extrinsic compensation mechanism, in which the extrinsic compensates the rigid part of each observation error at the residual level, and rotation and translation compensate each other at the parameter level. Consequently, the fitted residual can reveal neither an inconsistency between the observations and the model nor whether the estimated extrinsic is reliable in every direction. Accordingly, we assess the calibration through a structured covariance that jointly propagates the uncertainty of the camera and LiDAR board features with a known-geometry prior, and estimate its scale as a variance component from the residuals. On this covariance, we decouple rotation and translation to resolve the precision along each direction and guide data collection toward the weakest one. Since this precision presumes consistent observations, we further develop within-view and cross-view checks that examine the internal residual and the rigid discrepancy between observations, respectively, with thresholds that hold their significance level under an unknown noise level. We also extend the minimal detectable bias to the extrinsic to bound the smallest detectable fault along each direction. These criteria form a calibration state that indicates whether to accept the result or how to collect the data...

0.22

GR-LIO: A Local Ground-Aware LiDAR-Inertial Odometry System Using Body-to-Ground Height

cs.RO ·2026-10-04 ·Zhixin Zhang, Yang Song, Liang Zhao, Nathan Shankar, Barry Lennox +1 more
benchmark similarity 0.69
Abstract · 15 pages Journal

LiDAR-inertial odometry (LIO) is widely used for state estimation in ground-based autonomous mobile robots. However, the geometric constraints provided by the local ground surface remain largely underexploited in existing LIO systems. This paper proposes a filter-based local ground-aware LIO framework that explicitly incorporates local ground plane geometry into the state estimation process to improve both localization accuracy and computational efficiency. Specifically, a local ground plane is parameterized by the robot orientation and the body-to-ground (B-G) height and continuously propagated within the state estimation process. Based on the proposed B-G geometry model, a propagated local ground plane enables efficient and reliable ground segmentation. The segmented ground points are then incorporated into the filter update through point-to-plane geometric constraints, improving both state estimation accuracy and efficiency. Furthermore, a planar motion update is introduced to exploit the propagated local ground plane as an additional geometric constraint, effectively suppressing vertical drift and improving estimation robustness. To address the initially unknown B-G height, an efficient initialization strategy is developed, followed by an online calibration procedure for continuous refinement. The proposed system is evaluated on several public benchmark datasets and self-collected real-world datasets covering diverse operating scenarios. Experimental results demonstrate that the proposed method consistently outperforms representative LIO methods in terms of both localization accuracy and computational efficiency.

0.17

Observability Analysis of Joint Steering and Extrinsic Calibration

cs.RO ·2026-08-28 ·Subodh Mishra
similarity 0.67
Abstract

This technical report studies the local weak observability of a planar bicycle-model vehicle when vehicle pose, planar LiDAR extrinsic calibration, and steering-angle bias are estimated jointly. A Lie-derivative-based nonlinear observability analysis is used to examine stationary, straight-line, constant-curvature, and combined straight-plus-arc motion. The resulting observability matrices and nullspaces describe how pose, LiDAR translation and yaw offsets, and steering bias become coupled under different motion primitives. Stationary motion and individual motion primitives retain unobservable directions, whereas the combination of straight and curved motion removes the identified degeneracies and yields full local weak observability of the seven-state system. The analysis provides a theoretical basis for selecting calibration trajectories that sufficiently excite both steering and sensor-extrinsic parameters.

0.24

Real-Time Ground Normal Vector Estimation for Spherical Mobile 3D Mapping using LiDAR-Inertial Odometry

cs.RO ·2026-10-20 ·Tim Schubert, Fabian Arzberger, Andreas Nüchter
top venue similarity 0.65
Abstract · Proceedings of the International Symposium on Artificial Intelligence, Robotics and Automation in Space (i-SAIRAS 26)

Accurate ground plane normal estimation is essential for odometry in spherical mobile mapping systems (SMMS), which face challenges from rapid rotations and limited ground coverage. We propose two RANSAC-based approaches: single-scan estimation with normal vector scoring and multi-step validation, and LiDAR-inertial odometry (LIO)-based estimation using a global 3D map. Evaluated across diverse real-world datasets against terrestrial laser scanner ground truth, results show that LIO-based estimation significantly outperforms single-scan methods in accuracy and robustness. Integrating ground normal estimates into the motion model improves pose estimation, supporting autonomous navigation in challenging and hazardous environments.

0.25

Agreement Is Not Accuracy: LiDAR Elevation Errors Hidden in LiDAR-Camera Extrinsics

cs.CV ·2026-11-18 ·Yeon Kun Lee, Dongseok Yang, Deok-Kyeong Jang, Choongho Chung, Junyoung Lee +1 more
similarity 0.65
Abstract · 14 pages, 6 figures, including supplementary material

LiDAR and cameras provide complementary measurements for 3D vision, yet agreement between their observations does not establish the accuracy of either sensor's internal geometry. We show that systematic LiDAR elevation biases can be absorbed into the estimated extrinsics. Using synchronized LiDAR intensities and camera-estimated checkerboard poses, we jointly estimate a sensor-specific elevation correction shared across recordings and extrinsics for each recording. Ray-plane intersections locate the checker pattern without using reported ranges, preventing range errors from directly moving the lookup. Under matched intensity and correction models, this lookup gives smaller camera-consistency residuals than measured-point lookup. Across six identically designed rigs using the same sensor models, recording-excluded corrections reduce the mean translation-reference distance from 7.57 to 3.04 mm. On separate structures, they reduce inter-plane angle errors against references from independent dense camera scans and improve image-edge alignment. Rolling the rigs shifts the plane pairs exhibiting the largest angular improvements, as predicted for an elevation-only correction. Within the ray-plane model, calibration-target projections and loop-consistency residuals change little despite these geometric improvements. These findings show why agreement after extrinsic calibration need not establish correct internal LiDAR geometry. Synchronized observations of a familiar checkerboard provide a practical route to estimating and testing elevation corrections without a dedicated large calibration field. We plan to release code and data for reproducing the main results.

0.25

GLIO2: A GPU-Parallelized Tightly-Coupled LiDAR-Inertial-GNSS System for Robust and Real-Time Global Localization and Mapping

cs.RO ·2026-10-08 ·Qi Zhang, Xikun Liu, Qijun Qin, Xiangru Wang, Junzhe Wang +3 more
similarity 0.64
Abstract · 23 pages, 16 figures, 8 tables; includes appendices

Globally consistent, real-time state estimation in large-scale, perceptually degraded environments is essential for autonomous vehicles and aerial robots, and requires fusing LiDAR, inertial, and GNSS measurements. Existing fusion methods, however, share a scan-to-map front-end with two failure modes. First, each scan is aligned to an incrementally built map that drifts under degeneracy, and once the estimate diverges the error is irrecoverable. Second, even without divergence, a registration biased by dynamic objects or wrong correspondences is propagated as a single pose constraint with an over-confident covariance, leaving its correspondences unavailable for GNSS to re-weight or relinearize. We propose GLIO2, a tightly-coupled LiDAR-Inertial-GNSS system whose GPU-parallel front-end jointly optimizes scan-to-multiscan LiDAR, IMU pre-integration, and raw GNSS measurements in a single sliding-window factor graph, sustaining real-time operation on edge hardware. A complementary offline back-end reuses the same cached factors to refine the entire trajectory in batch, completing the 30-min, 4.51-km UrbanNav Whampoa sequence in about 24 s. Across three public benchmarks (UrbanNav, MARS-LVIG, M3DGR) and self-collected UAV and vehicle data, GLIO2 attains the best overall accuracy among evaluated systems. On a 5.66-km bridge traversed at up to 96 km/h, where every competing baseline diverges under LiDAR degeneracy, it maintains 1.6 m horizontal accuracy. On an NVIDIA Jetson Orin NX, the full pipeline runs at about 25 Hz (39.60 ms per scan). The source code and datasets will be released.

0.21

Online Joint Calibration of Steering Offset and Planar LiDAR Extrinsics for Wheeled Mobile Robots

cs.RO ·2026-08-27 ·Subodh Mishra, Arindam Dhar, Suprotim Majumdar, Naveen Arulselvan
similarity 0.63
Abstract

Accurate steering sensing and LiDAR-to-vehicle extrinsics are crucial for reliable path tracking in warehouse mobile robots (WMRs); miscalibration often leads to snaking, weaving, and elevated cross-track error (CTE). In practice, steering ``zero'' is commonly set manually (e.g., eyeballing straightness via a PS4 joystick), while LiDAR extrinsics are assumed from CAD and may drift after maintenance. Such static, manual procedures frequently cause miscalibration in safety-critical environments. This paper presents an Extended Kalman Filter (EKF)--based method for online estimation of steering offset and planar LiDAR extrinsics within a bicycle-kinematics model, providing a principled alternative to manual calibration. Experiments on real datasets show that correcting steering offset reduces CTE substantially, validating the effectiveness of the proposed approach.

0.29

GHySSeg: Real-Time Geometric Ground and Road Segmentation for Hybrid Solid-State LiDAR

cs.RO cs.CV ·2026-11-16 ·Martín Palos, Fernando García
benchmark similarity 0.63
Abstract · 14 pages, 8 figures, 3 tables. Submitted to IEEE Transactions on Intelligent Transportation Systems. This work has been submitted to the IEE…

Hybrid solid-state LiDAR sensors are making their way into production vehicles, yet the data they produce differs structurally from that of the established spinning mechanical sensors behind today's autonomous-driving datasets: it is ring-free, dense, cluttered, and concentrated in a frontal field of view. The classical geometric methods that autonomous vehicles rely on for drivable space computation and navigation assume the ordered ring-and-column structure of a 360-degree spinning LiDAR and degrade or fail on this data, while learned alternatives are computationally heavy, hard to certify, and trained almost exclusively on spinning-LiDAR data. We demonstrate that the same dense, per-curve geometry is instead an opportunity to close the divide between the industry's preferred sensors and autonomous-driving research. We present GHySSeg, a purely geometric method that segments ground and drivable road from a single hybrid solid-state LiDAR frame by tracing each scan curve and reading two geometric signatures, a step in height and a fold-back in range, with no training and no graphics processing unit. To evaluate it, we release HySoLiD-Drive, the first public benchmark dedicated to ground and road segmentation on an automotive hybrid solid-state LiDAR, comprising 100 manually labeled and 7000 unlabeled frames recorded by two vehicles in real driving. On this benchmark, GHySSeg surpasses both geometric and learned state-of-the-art baselines across ground and road segmentation, reaching an intersection-over-union of 0.907 for road and 0.896 for ground at over 0.96 precision, while running in real time at about 22 milliseconds per frame on a single core.

0.42