CS Paper Radar

Planning a Shared Modular Fixture Layout Across Robotic Disassembly Stages

Haohui Pan, Takuya Kiyokawa, Kensuke Harada

cs.RO ·submitted 2026-08-27 14:03 UTC · v1

Abstract

Stable support remains challenging in robotic disassembly of irregularly shaped products. As components are progressively removed, the available support surfaces, mass distribution, and task loads change throughout the process. A fixture layout designed for one workpiece state may therefore become infeasible at later stages, motivating unified support planning over the complete disassembly sequence. This paper presents a modular vacuum-based fixturing system that plans one shared support configuration for the complete disassembly sequence of a screwdriver or shaver, allowing each sequence to proceed without fixture reconfiguration. To search the mixed continuous--discrete layout space under repeated cross-stage evaluation, a denoising diffusion probabilistic model generates physics-informed initial configurations that are refined through Bayesian optimization. Robotic screw and component-removal experiments verified the disassembly feasibility of the planned layouts, while 11 directional-load tests quantified their stability. Comparisons between the measured operational loads and directional responses yielded mean empirical stability margins of 66.9% for the screwdriver and 81.6% for the shaver. These results demonstrate that a product-specific shared layout can provide stable support throughout the tested robotic disassembly sequence.

Comment
15 pages, 9 figures. Submitted to IEEE Transactions on Automation Science and Engineering (T-ASE)

Closest papers

Nearest neighbours by meaning across the whole index.

WRAP: Fixtureless Wrench-aware Multi-Robot Assembly Planning

cs.RO ·2026-09-24 ·Valentin N. Hartmann, Huang Su, Yijiang Huang, Stelian Coros
benchmarkcode/data similarity 0.60
Abstract · 8 pages, 9 figures, 5 tables

Assembly using robots often requires specially designed fixtures, or relies on top-down only assembly strategies. Using multiple robots, we can avoid using fixtures and make robotic assembly more flexible. Planning assembly sequences for multiple robots is challenging due to the high number of possible task assignments and orders. In addition, we need to reason over forces that occur during the assembly process, e.g., to decide if multiple robots are required for support, or if external support such as a table should be used. We present Wrap, a multi-robot assembly planner for multi-part assemblies, given the inter-part ordering-dependencies, the part meshes, and their initial state. We formulate a linear program to reason about valid grasps for supporting the forces that occur during assembly. The search leverages the assembly sequence, and greedily finds a feasible solution per assembly step by computing a heuristic via a cheap backwards search, and using the heuristic in the more expensive forward search. We then solve the multi-robot, multi-goal motion planning problem, and for execution, we split the plan into contact-rich assembly skills, and free space motion. We benchmark the planner on a variety of multi-part assemblies, and apply the planner to groups of robots differing in size and kinematics. We validate the work both in a physics simulation, and in real. Videos and code are available at https://www.vhartmann.com/wrap.

0.33

On-Demand Robotic Assembly via Differentiable Geometric Part Repair

cs.RO ·2026-10-07 ·Millicent Schlafly, Fabio Schaub, Diogo Costa Pais, Luca Lelli, Janne Dvorak +3 more
similarity 0.59
Abstract · 8 pages, 4 figures, and 2 tables

Transitioning from a digital design to a robotic assembly process currently requires months of expert manual tuning to reconcile part geometries with robotic constraints. This paper presents an end-to-end, autonomous pipeline for the design and physical construction of bespoke wooden assemblies. A generative AI agent translates user prompts into initial 3D geometries, balancing the visual fidelity of the design with select physical constraints. The assemblability of the design is further improved by a gradient-based repair stage that backpropagates through a graph attention network surrogate to adjust component geometries. In addition to correcting for disjointed and overlapping components, we demonstrate hardware-specific corrections, differentiably optimizing the geometry of components to enable robot screwdriving for 86.7% of 60 novel natural language inputs, significantly outperforming prior work by a factor of ten. For ten of the structures, we physically demonstrate assemblability with two UR5e robots. This work marks a meaningful step toward on-demand robotic manufacturing, enabling the rapid production of customized, low-volume goods.

0.30

Backward Layout Search for Sequence-Constrained Robotic Assembly

cs.RO ·2026-08-19 ·Xi Zhang, Jiancong Dai, Hao Chen, Zhengtao Hu, Changcai Yang +1 more
similarity 0.59
Abstract · Submit to ROBIO2026

Robotic assembly layout planning must determine the assembly site and the initial pose of each part while ensuring collision-free execution of a prescribed assembly sequence. This problem is challenging because the obstacle environment changes after each assembly step, and unassembled parts re maining in the workspace may block robot motions. We observe that the feasibility of each assembly step depends only on the initial poses of the current and later-assembled parts. Based on this dependency, we propose Backward Layout Search (BLS), which assigns initial part poses in reverse assembly order. Each expansion performs geometric, kinematic, grasp, and prescribed-motion checks, while collision masks and candidate set filtering remove infeasible initial part pose candidates. Promising partial layouts are retained through beam selection, and complete layouts are validated by full motion planning in forward assembly order. Experiments on five assembly models show that BLS produces collision-free executable layouts and reduces step evaluations and search time compared with a matched forward search.

0.31

End-to-End Autonomous Generation of Human Assembly Plans

cs.RO cs.GR ·2026-10-07 ·Faustin Arion von Arx, Millicent Schlafly, Mark D. Fuge
code/data similarity 0.58
Abstract · 22 pages, 10 figures

Turning a CAD design into an assembly plan is still largely done by hand, requiring engineers to reason about geometric feasibility, tool access, stability, and the ergonomics of human assembly. In this work, we encode long-established design for assembly (DfA) principles into a contained, end-to-end approach for generating assembly plans. Our approach takes only a mesh assembly and produces either a step-by-step assembly manual or a structured failure report, requiring no joint metadata, fastener annotations, or additional information. Four major components of a manufacturing plan are addressed autonomously: an assembly tool list, the assembly sequence and subassemblies, an assembly manual, and design feedback for improving assemblability. For determining the sequence plan, we systematically disassemble the object in a physics simulator and apply a cost function that encodes DfA principles. Manual generation, tool labelling, and assembly feedback rely primarily on multimodal large language models. Compared with a baseline that always removes the outermost part first from Tian et al., DfA-aware sequence planning reduces simulated assembly time, measured with a robot-arm assembly-time proxy, by 35% on 136 assemblies of 5 to 30 parts. The correct tool is selected for 88.6% of assembly steps. A vision-language model judge compares the generated manuals against ablated variants, identifying which page elements carry the information a reader needs. The presented approach and open-source code are available for use by engineers or AI agents looking to rapidly accelerate the creation of manufacturing plans for a given product design.

0.39

Fastener-centric acquisition and AND/OR graph representation of state-dependent disassembly knowledge from CAD-derived virtual assemblies

cs.RO ·2026-11-09 ·Shiki Iwase
similarity 0.58
Abstract

Design-stage disassemblability assessment requires knowledge of product structure and the operations available in each assembly state, but CAD assemblies do not directly specify state-dependent disassembly operations. This paper proposes a fastener-centric virtual-disassembly framework that acquires such knowledge from CAD-derived virtual assemblies. Fasteners jointly releasing the same constraint are grouped into operation-level sets, avoiding enumeration of arbitrary individual-fastener orders. Their removability is evaluated through state-dependent visibility and tool-access checks and torque-driven virtual-removal trials. After fastener removal, graph-based reasoning identifies candidate moving units, whose separation is evaluated by initial-motion screening, path generation, and physics-based validation. The acquired operations, states, dependencies, validated paths, and simulation-derived attributes are organized into a Transformed AND/OR Graph for subsequent planning and design evaluation. Exhaustive verification with a controlled toy assembly found no branching violations for introduced tool-accessibility and precedence conditions. Evaluation with a 54-component OpenManipulator Chain gripper demonstrated state-dependent fastener-removal and part- or subassembly-separation operations. Visibility and tool-accessibility evaluations pruned 51.4% of fastener-set candidate evaluations, while removal of obstructing components enabled previously inaccessible fastener operations. Operation-level grouping and screening thereby limited detailed physical validation to mechanically plausible candidates. The results demonstrate the feasibility of acquiring product-specific disassembly knowledge from CAD-derived virtual assemblies before manufacture, supporting subsequent disassembly reasoning and design-for-disassembly evaluation.

0.19

AssemblyWorld: Rethinking 3D Assembly with General-Purpose Agents

cs.CV cs.RO ·2026-09-30 ·Jiahao Zhang, Yeying Fan, Moitreya Chatterjee, Suhas Lohit, Bernhard Egger +3 more
code/data similarity 0.56
Abstract · 24 pages, 11 figures. Project page: https://assemblyworld.github.io

The task of 3D assembly requires translating an understanding of parts and their relationships into precise spatial arrangements. Can pretrained general-purpose agents assemble objects through visual interaction without additional assembly-specific fine-tuning? To investigate this question, we introduce AssemblyWorld, an interactive 3D environment in which agents inspect rendered views and manipulate supplied rigid parts, guided by images or assembly manuals when available. Agents perceive part geometry through 2D views rather than direct access to mesh vertices or faces, while their resulting assemblies are evaluated geometrically. Building on this environment, we construct AssemblyWorldBench, comprising 100 assembly tasks across 80 objects spanning furniture, industrial assembly, and fracture reassembly. Evaluating eight agent systems reveals substantial differences in their capabilities. The strongest system achieves 80.9% part accuracy but 59.4% complete-assembly success. The evaluated open-source systems lag substantially behind their stronger closed-source peers in both execution reliability and assembly accuracy. Analyses of visual references, interaction trajectories, and failures show how agents revise assemblies while leaving residual positioning errors. AssemblyWorld provides a common setting for both assessing the capabilities of interactive assembly agents and characterizing the gap between approximate structure recovery and precise reconstruction.

0.28

Tool-Policy Co-Design for Powder Weighing in Laboratory Automation

cs.RO ·2026-09-30 ·Nikola Radulov, Xin Yang, Kevin S. Luck, Gabriella Pizzuto
similarity 0.55
Abstract · Paper video can be found at https://youtu.be/BEUT70hX9LM

Autonomous powder weighing is one of many bottlenecks in laboratory automation due to the complex, non-linear dynamics of heterogeneous materials. Robot chemists performing this task utilise standard tools shaped for the dexterity of human hands, whose fixed geometry sets the dynamics that the control policy needs to regulate. This work introduces a tool-policy co-design framework that concurrently optimises the morphology of a dispensing tool and its control policy for use by robots in chemistry laboratories, formulated as a bi-level optimisation that minimises dispensing error over a target distribution of powder flowabilities. The outer loop varies tool-design parameters such as tool depth, width and rim spike topology using Bayesian optimisation and hyperband, while an inner loop optimises a control policy for each candidate morphology. We also introduce a geometric similarity metric that warm-starts policy training from cached policies of structurally similar designs, exploring 28% more configurations under the same compute budget. The proposed framework is evaluated on a robotic powder weighing task across seven materials with distinct physical dynamics in a flowability-informed robot-material simulation framework. Experimental results demonstrate that our co-designed tool morphology reduces real-world weighing errors by 45% relative to a standard tool, including on previously unseen materials. These results demonstrate our method can adapt both the control policy and the physical tool to the dynamics of the target material, bringing a new paradigm for material manipulation to the field of laboratory automation.

0.35

LABIT: Long-Horizon Robotic Assembly Benchmark for Industrial Tasks

cs.RO ·2026-10-12 ·Constantin Schempp, Christian Friedrich, Luca Kofler, Laura Suhm
benchmarkcode/data similarity 0.54
Abstract · This work has been submitted to an Elsevier journal for possible publication. Copyright may be transferred without notice, after which this …

Robot learning has undergone significant advancements in the domain of compliant control and robotic assembly. The development of novel methodologies has transcended the capacity to address discrete tasks, such as grasping or inserting, and has evolved to encompass the comprehensive construction of entire assemblies. Conventional benchmarks, which are predominantly focused on single tasks, are no longer adequate to address the complexity and interconnected nature of modern manufacturing processes. Consequently, the necessity for benchmarks to encompass a broader spectrum of assembly and subassembly steps is becoming apparent. In light of these developments, we propose LABIT, an industrial robotic assembly benchmark for long-horizon manipulation. This benchmark encompasses DIN-norm assembly tasks, including screwing, placing, inserting, and snapping, under both high and low tolerance conditions. The successive nature of these assembly steps implies that prior errors can influence subsequent manipulation. Consequently, this benchmark is particularly relevant for assessing the robustness of intelligent robotic systems. The proposed benchmarking protocols and novel performance metric, based on a taxonomy of assembly complexity in conjunction with the comprehensive list of parts and their corresponding CAD models, serve as essential tools for research and development in the field. To provide a baseline, we evaluate the benchmark using traditional force-position control and report reliability and score metrics per primitive, subtask, assembly category, and subassembly. Accompanying data is available at https://irp-hka.github.io/robotic-assembly-benchmark/.

0.48