CS Paper Radar

CAHR-Net: Condition-Adaptive Hysteresis Reconstruction for Compact and Interpretable Magnetic Core Loss Modeling

Chunye Gong, Cong Yao

cs.LG ·submitted 2026-09-02 01:54 UTC · v1
publishedunusual

Abstract

Magnetic core loss originates in the hysteresis loop: the energy dissipated per excitation cycle equals the loop area, and frequency, temperature, and waveform shape set the loss by reshaping the loop geometry. Most existing models let these conditions act only on a terminal scalar - empirical equations fold them into fitted exponents, and data-driven predictors append them to encoded features - so no intermediate hysteresis representation remains for the conditions to reshape. This paper proposes CAHR-Net, a condition-adaptive hysteresis reconstruction network that injects the operating conditions where they physically act. It preserves the interpretable chain from flux density waveform to magnetic field reconstruction, loop-area integration, and power loss estimation, and uses feature-wise linear modulation to inject frequency, temperature, and waveform statistics into the intermediate reconstruction representation. A matched large-batch training protocol based on AdamW, cosine scheduling, and a staged reconstruction-to-power-loss objective is also reported, because the modulation pathway takes effect only within it. On the MagNet final A-E material protocol, CAHR-Net attains an average p95 relative error of 6.89% with only 1874 parameters, the lowest among all compared methods, together with a lower worst-material p95 than the strongest black-box solution at about 48x fewer parameters; it reduces the average p95 of the physical reconstruction backbone from 7.47% to 6.89% and the p95 of material D, the most difficult material, from 16.40% to 14.87%. Ablation and condition-slice analyses attribute the improvement to the coupling of physical loop reconstruction, structured condition modulation, and the matched optimization trajectory.

Comment
10 pages, 6 figures, 5 tables

Closest papers

Nearest neighbours by meaning across the whole index.

MagLearn 2: High-Fidelity, Saturation-Aware, and History-Efficient Sequence-to-sequence Modeling of Transient B-H Behaviour Under PWM Excitation

eess.SY ·2026-10-02 ·Jingrong Yang, Binyu Cui, Yuming Huo, Lizhong Zhang, Alfonso Martinez +2 more
similarity 0.59
Abstract · Submitted to IEEE Transactions on Power Electronics (TPEL) for peer review. An earlier conference version of this work was published in IEEE…

Accurate transient B-H modeling under pulsewidth-modulated (PWM) excitation is challenging since the magnetic-field response depends on both the instantaneous flux density and the preceding magnetisation trajectory. Although sequence-to-sequence models enable waveform prediction, existing studies have not jointly addressed how much magnetic history is required, how saturation region should be handled, and how trained models can be adapted to unseen materials. To address these gaps, this paper presents MagLearn 2, a condition-aware, short-window LSTM-based sequence-to-sequence framework for reconstructing the future H(t) response from the historical B(t) and H(t) trajectories. A saturation-aware auxiliary module selectively replaces saturation-dominated predictions within the complete waveform forecast. In a representative saturated 3C90 case, the auxiliary module reduces the sequence-level relative RMSE from 67.84% to 9.19%. To understand how much the history samples contributes to the predictions, an occlusion-based sensitivity analysis is conducted to quantifies the contribution of magnetic history and reveals that that the information most relevant to prediction is concentrated near the forecast boundary. In the independent evaluation for MagNet Challenge II, the proposed framework's best-performing model achieved the lowest reported average RMSE to date on the sequence-prediction task at 2.2%.

0.56

Cross-Material Magnetic Core Loss Prediction via Operating-Condition Matching and Partial Optimal Transport

cs.LG ·2026-10-10 ·Cong Yao, Yu Zheng, Zehao Hou, Rui Xu
similarity 0.58
Abstract · 11 pages, 9 figures, 6 tables

Cross-material magnetic core loss prediction requires adapting to new material responses with limited measurements. Global feature alignment overlooks differences in source and target excitation coverage. This motivates selecting comparable samples and controlling each source measurement's alignment contribution. This paper proposes T-PCOT, a Transformer transfer method based on condition-supported partial optimal transport. Frequency, flux excursion, temperature, and waveform descriptors define a sparse graph of comparable operating conditions. A capacity-constrained transport plan distributes alignment across source measurements and leaves costly target mass unmatched. The plan is constructed from measured inputs before training and guides local waveform-feature consistency. An importance-weighted sampling scheme preserves both uniform source regression and the transport objective during minibatch optimization. Experiments on three material pairs and three target label budgets show that T-PCOT reduces mean relative error (MRE) and 95th-percentile error (P95) relative to Transformer-based multiple-kernel maximum mean discrepancy (T-MKMMD) in all nine comparisons. Macro MRE decreases from 12.60% to 9.65%, and macro P95 from 30.94% to 25.06%, corresponding to relative reductions of 23.41% and 19.01%. Controlled comparisons and ablations examine the roles of input processing, condition correspondence, and source capacity. The results demonstrate the predictive advantage of organizing cross-material alignment through operating-condition support over the compared global alignment method. The proposed method achieves state-of-the-art predictive performance in magnetic core loss transfer learning.

0.18

A Data-Driven, Gain-Scheduled Equivalent Circuit for the B-H Behavior of Power Ferrites

eess.SY ·2026-11-01 ·Wilhelm Kirchgässner
similarity 0.56
Abstract

An equivalent circuit for the dynamic B-H behavior of power ferrites is identified from measured transients. It consists of classical elements of hysteresis modeling: a nonlinear inductor for the reversible curve, six viscous play branches (inductors in series with diode-bridge sliders) that form a Prandtl-Ishlinskii model, two R-L branches for the magnetic after-effect, a mean-field feedback of H as in the Jiles-Atherton model, and a measurement path. All elements are positive apart from the feedback sources, and the circuit can run in SPICE. Discretized at the sampling step, the circuit is a difference equation with 32 parameters per material, fitted by backpropagation through time. On the 15 materials of the MagNet Challenge 2, the mean sequence relative error is 7.33 % against 7.77 % for the challenge-winning recurrent network with 336 parameters, and the circuit is more accurate on 12 of the 15 materials. The accuracy can be scaled up by gain scheduling, where a small network per material sets the element values at every step from the excitation, while the hysteresis memory stays in the circuit, such that the error drops to 5.25 % with 656 parameters per material. Thus, an interpretable model is demonstrated that achieves state-of-the-art accuracy.

0.29

Cross-Material Support Transfer for Core-Loss Prediction Under Waveform Covariate Shift

cs.LG cond-mat.mtrl-sci ·2026-09-15 ·Cong Yao, Chunye Gong
similarity 0.54
Abstract · 10 pages, 7 figures, 5 tables

Power magnetic materials are characterized on the sinusoidal and triangular waveforms that excitation hardware conveniently produces, whereas deployed converters expose cores to trapezoidal, PWM-shaped flux trajectories, so loss models must predict exactly where their training data are thinnest. The final test of the MagNet Challenge embeds a deliberately extreme instance of this characterization-deployment mismatch: for material D, trapezoids form 16.4% of the test set but only 1.4% of the training set. The 95th-percentile relative error, hereafter p95, of the best submission, built on sequential transfer learning, stalled at 15.9%, the worst among the five materials. This paper shows that the obstacle is missing information under covariate shift rather than class imbalance, and that the missing support can be borrowed from sibling materials instead of being extrapolated. Controlled experiments first refute the imbalance reading: four standard remedies fail, and raising the trapezoidal share to the test-set level degrades accuracy further. The proposed material-identity support transfer, MIST, then trains one 2784-parameter predictor jointly on all five challenge materials. Material identity enters through feature-wise linear modulation, or FiLM, the scarce material's true-label loss is reweighted, and material D receives no fine-tuning, so that the bias of its trapezoid-free training set is never re-installed. MIST lowers the five-seed material-D p95 from 20.39+/-2.03% to 12.38+/-0.92% and the trapezoidal-class p95 from 37.4+/-8.8% to 15.16+/-1.69%, surpassing the best submission with one-sixth of its parameters and no fine-tuning stage; removing material identity at matched capacity inflates the error by an order of magnitude. These results argue that scarce materials should be characterized jointly with their siblings.

0.33

Physics-Guided Inferencer-in-the-Loop Digital-Twin for Real-Time Adaptive Emulation of Nonlinear PMSMs

eess.SY ·2026-10-28 ·Songyang Zhang, Yuzhong Zhang, Venkata Dinavahi
similarity 0.51
Abstract

A real-time digital-twin (RTDT) of a permanent magnet synchronous machine (PMSM) allows drive controllers to be tested in hardware-in-the-loop (HIL) before they meet the real machine. Its machine model rests on identified parameters or flux look-up tables (LUTs) from finite-element analysis (FEA) or characterization tests; the maps are regenerated offline when the machine changes, and online estimators track a few parameters such as resistance and PM flux. This article makes the executed model learnable from reference data. A physics-guided machine learning (PGML) network advances the currents and predicts torque in one step, trained with analytical one-step labels. In the proposed Inferencer-in-the-Loop (IIL) architecture, a GPU retrains the network while a field-programmable gate array (FPGA) executes the last accepted weights. For damper circuits, shifted parameters, and an FEA-calibrated saturated machine, one kernel form reaches average normalized mean absolute errors (NMAEs) of 0.19%-0.67% at measured FPGA kernel latencies of 0.30-0.34 $μ$s, and retraining for a shifted machine nears its final loss within 94 s. On a magnetically linear 200-W drive, a residual form corrects the analytical step and learns its physical parameters from operating data; each step takes under 2.5 $μ$s, 20 times faster than real time and ahead of the physical drive's measurements even at 20-kHz sampling. On six held-out runs (1193 s), its $i_q$ error is 5.9%-9.4% of measured RMS, against 10.4%-13.2% for an independently fitted grey-box model, and over 30 min of loaded heating its online-updated heads track a 4.1% winding-resistance rise with an RMS error of 0.44 m$Ω$.

0.29

Stray Losses in Power Transformers: A Comparative Study of Modeling Frameworks for Mild Steel

eess.SY ·2026-11-03 ·Micha Swaanen, Timo Overboom, Siamak Pourkeivannour, Tom Huiskamp, Guus Pemen
benchmarkunusual similarity 0.50
Abstract · 13 pages, 18 figures. Submitted to IEEE Transactions on Magnetics

Accurately predicting eddy-current and hysteresis losses in mild steel components such as the structural parts and tank of power transformers remains a challenge in transformer design. Conventional numerical approaches for eddy-current loss analysis require discretization at a fraction of the skin depth. While accurate, such fine volumetric mesh becomes computationally prohibitive for large power transformers. Moreover, hysteresis loss is not always included in this analysis. To investigate the trade-off between computational cost and accuracy, this work presents a comparative analysis of eight distinct modeling frameworks for predicting both eddy-current and hysteresis losses in mild steel. These include efficient methods avoiding meshing, such as standard impedance boundary conditions, and more accurate approaches retaining full volumetric meshing, namely complex permeability, nonlinear single-valued B-H curve, and Jiles-Atherton hysteresis modeling. To accurately represent the material's electromagnetic behavior, the properties of the mild steel used are measured directly from samples. Finally, loss measurements are conducted to benchmark all eight frameworks, demonstrating mean absolute percentage errors between predictions and measurements generally below 20%.

0.33

Physics-Constrained Autoencoder for Interpretable Health Representation Learning in Turbofan Engines

cs.LG eess.SP ·2026-11-10 ·Leonardo Baldo, Jokin Alcibar Ibarzabal, Daniel Cisneros Acevedo, Kai Goebel, Manuel Arias Chao
similarity 0.50
Abstract

Health Indices (HIs) summarize degradation from operational data and support diagnostic and prognostic tasks in Prognostics and Health Management (PHM). Their usefulness depends on capturing degradation and interpreting system condition. Autoencoders learn such representations from unlabelled monitoring data; however, when training is driven only by reconstruction, the physical meaning of latent variables remains undefined, limiting their interpretation and diagnostic value. This work proposes a physics-constrained autoencoder that embeds system knowledge as an inductive bias in the decoder architecture and as a learning bias in the loss function. The decoder contains differentiable physical equations that receive latent variables and operating conditions as inputs, structurally guiding each latent variable to represent a predefined physical quantity and enabling component-level analysis before aggregation into a system-level HI.The methodology is benchmarked on the N-CMAPSS dataset against alternative representations. Reconstruction reaches an $R^2$ of 0.9993 and an MAE of 0.0036, comparable to fully data-driven models. After operating-condition correction, the inferred physical quantities track degradation, and their aggregation produces an HI with a Spearman correlation of 0.9791 with the ground truth, an RMSE of 0.0286, and an MAE of 0.0233. The methodology is further evaluated using a single model trained across four datasets representing distinct degradation scenarios. This model preserves component-level signatures that distinguish compression-side from expansion-side degradation without diagnostic labels.Finally, the proposed framework enables degradation trends to be visualized on component maps, providing a health representation in a form familiar to engine operators and domain experts.

0.22

Adapting neural operators for mechanics decisions under changing operating conditions

cs.CE cs.LGmath.NA ·2026-09-27 ·Prashant K. Jha, Koffi Enakoutsa, Ian Galloway, Henry Anderson
similarity 0.50
Abstract · 33 pages, 16 figures

Neural operators can accelerate repeated nonlinear mechanics calculations, but their accuracy can deteriorate as operating conditions move beyond the training range. This work studies whether high-fidelity solutions acquired during use can be reused to adapt a neural operator and improve subsequent mechanics-based command selection. Two hard-magnetic soft-material systems are simulated using high-fidelity finite-element (FE) models, providing reference solutions for evaluating surrogate predictions and selected commands. A neural operator predicts deformation from known material, loading, and magnetic-field inputs, while an empirical error estimator determines which predictions may be used for command selection. Selected FE evaluations supplement these predictions, and their complete loading paths are retained for periodic updates of the neural operator and estimator. In both examples, the fixed operator loses substantial accuracy when stiffness and loading move outside the training range. Updates using 16 acquired paths recover much of the lost accuracy while preserving accuracy in the nominal regime. Under the same FE evaluation budget, the updated operators also improve command selection, although the benefit varies with the operating condition. Error estimation is less consistent, with inaccurate predictions sometimes accepted and accurate predictions rejected. These results demonstrate that reusing high-fidelity loading paths can extend the useful operating range of a neural operator. However, improved forward accuracy alone does not guarantee reliable prediction acceptance, highlighting prediction-specific error assessment as a separate requirement for trustworthy decision making.

0.36