CS Paper Radar

Design and Attitude Control of an Underwater Quadruped Robot

Davide Molinaroli, Mohit Singh, Kostas Alexis

cs.RO ·submitted 2026-09-06 17:19 UTC · v1
published

Abstract

Legged robots are versatile on land, but their use in underwater environments remains limited. Extending quadruped locomotion to water enables amphibious mobility with applications in inspection, environmental monitoring and disaster response. This paper presents the design, modeling, and experimental validation of a reproducible underwater quadruped robot. The robot is built around custom waterproof motor housings machined from polyoxymethylene plastic, which use off-the-shelf O-rings and dynamic shaft seals. A simplified model is derived to describe the dynamics of this underwater legged system, capturing how drag forces on spherical end effectors transmit torque to the floating base. Building on this model, a closed-loop attitude controller is developed using an error formulation defined on the special orthogonal group SO(3). The controller is evaluated both in simulation and experimentally in a water tank, where the robot tracks desired orientation setpoints in roll, pitch and yaw.

Comment
16 pages, 8 figures. Accepted to ISRR 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Multifunctional Locomotion Control of Multi-Jointed BURs with Swimming and gait Capabilities

cs.RO ·2026-09-29 ·Takumi Asada, Hideo Furuhashi, Kenta Tabata, Renato Miyagusuku, Koichi Ozaki
publishedcode/data similarity 0.65
Abstract · Preprint version of an article published in Advanced Robotics (2026)

Multimodal biomimetic underwater robots (BURs) can conduct underwater tasks suitable for the environment. Combining the characteristics of aquatic organisms enables the swimming and leggedlocomotion required for underwater exploration. Locomotion control mechanism relies on rule-based behavior selection and the designer's discretion. This limits the robot's ability to acquire new behavioral capabilities to the predetermined range of behaviors. To address these challenges, we propose a mechanism and control system that enables the expression of multimodal locomotion capabilities from the same multi-jointed structure. A mechanism equipped with four leg-fins each having four axes is used. This controller achieves nonlinear behavior based on sensor modalities, rather than relying on predefined conditional rule-based on locomotion functions. This system was validated through both physical and simulation testing based on multiple sensor data and behavioral patterns. Utilizing a potential function in multimodal locomotion control was verified to enable transitions between two or three behaviors. Implementing the control method as a multimodal controller is expected to enhance its application in underwater exploration. Our project page is at https://tasada038.github.io/multi-jointed-bur/.

0.41

Swim-and-Breach at Palm Scale: A Rudder-Steered Two-Propeller Underwater Robot Platform with Differential-Thrust Pitch Control

cs.RO physics.flu-dyn ·2026-09-15 ·Daehyun Choi, Ian Bergerson, Hengjia Zhu, Tianjun Lan, Saad Bhamla
similarity 0.61
Abstract

We present a palm-scale (65 mm, 34 g) swim-and-breach robot platform. Two vertically stacked propellers provide both propulsion and differential-thrust pitch control under a proportional-integral-derivative (PID) loop, and a tail rudder adds yaw control. The hull, evaluated by flow simulation, reduces the drag five-fold relative to an equivalent cuboid, and the propellers are optimized using B-series modeling validated by dynamometer measurements. The current robot swims at 13.9 body lengths per second and turns at 209 deg per second, corresponding to the upper limits reported for underwater robots. In free swimming, the pitch loop turns the body to any commanded nose-up pitch angle, and, with the rudder stabilizing the exit, the current robot leaps 1.6 body lengths high and 3.7 long in a seamless cruise-leap-cruise sequence. The platform can be used to build small-scale robots that cross barriers and dry gaps between pools for inspection in streams, flooded structures, and industrial systems.

0.27

Omnidirectional Amphibious Locomotion via Internal Mass Actuation

cs.RO ·2026-09-23 ·Niko Weaver, Boxi Xia, Li-Yu Lo, Yuhao Huang, Boyuan Chen
code/data similarity 0.55
Abstract

Field robots must traverse varied terrain and obstacles while remaining robust to water, debris, vegetation, and physical contact. We present MARBLE, a fully enclosed omnidirectional amphibious rolling robot driven entirely by internal mass redistribution. Three mutually orthogonal linear sliders shift internal masses to generate body rotation, while an orientation-aware controller maps planar velocity commands into slider positions. A rigid spherical shell encloses all active mechanisms and simultaneously serves as the terrestrial contact surface, buoyant enclosure, and mounting structure for passive fins that enable water-surface propulsion. Rotation of the same shell architecture hence produces rolling on land and surface propulsion in water without mechanical reconfiguration or separate locomotion actuators. The spherical morphology further allows the robot to accommodate changes in body orientation and contact location during direct interactions with terrain and obstacles. We evaluate MARBLE through omnidirectional locomotion characterization, traversal across heterogeneous terrestrial environments, aquatic surface locomotion, land-water transitions, and deliberate obstacle interactions. These experiments demonstrate how a single enclosed mechanical architecture can combine omnidirectional mobility, cross-medium locomotion, and tolerance to environmental contact. MARBLE provides a compact design for field mobility across heterogeneous terrain, obstacles, and land-water transitions. We will open-source all software and hardware design. Our website is https://generalroboticslab.com/MARBLE

0.44

ClimbLab: MATLAB Simulation Platform for Legged Climbing Robotics

cs.RO ·2026-10-07 ·Kentaro Uno, Warley F. R. Ribeiro, Yusuke Koizumi, Keigo Haji, Koki Kurihara +2 more
publishedhighly cited similarity 0.54
Abstract · Author's version of a manuscript in the proceedings of CLAWAR 2021. The final published version is available at: https://doi.org/10.1007/978…

This paper presents an open-sourced MATLAB simulation and analysis platform dedicated to legged climbing robots. This simulator enables the design of any limbed robotic system as an articulated multi-body with a floating base and simulates it walking and climbing in an arbitrary environment. The main variable environmental parameters are inclination, gravity, and ground stiffness, and any point cloud can be installed as the terrain map. Furthermore, the simulator employs a rigid body dynamics engine. This paper first describes the simulator structure, and the computational flow and next presents the representative simulation examples where quadrupedal robots assumed gripping on the wall or climbing on the steep slope.

0.67

Differentiable Hydrodynamics for Whole-Body MPC of Underwater Robots

cs.RO ·2026-11-19 ·Hefan Wang, Yvan Petillot, Carlos Mastalli
similarity 0.53
Abstract

Underwater vehicle-manipulator systems distribute actuation across thrusters and joint motors. Whole-body model predictive control (MPC), rather than separate vehicle and arm controllers, can coordinate both to extend the workspace and exploit the system's full kinematic capability. Doing so, however, requires a hydrodynamic model and derivatives throughout the prediction horizon. Computational fluid dynamics (CFD) captures geometry-dependent forces and moments for such a model, but is too expensive to evaluate online. We present a differentiable analytical hydrodynamic model combining smooth spherical-harmonic force and moment fields with a coupled added-inertia matrix identified from CFD. It compactly represents velocity and acceleration-dependent loads and provides their derivatives in closed form. These derivatives are propagated through free-floating vehicle--manipulator dynamics for whole-body trajectory optimization and receding-horizon control, jointly optimizing thruster forces and joint torques for reaching and continuous tracking. Held-out CFD tests validate the principal translational-force and rotational-moment fields and the added-inertia response. The analytical Jacobians evaluate faster and avoid the step-size sensitivity of central finite differences. Closed-loop Stonefish experiments demonstrate whole-body MPC in an independent marine simulator. By making geometry-dependent hydrodynamics directly available to gradient-based control, the model incorporates water forces and their sensitivities into motion allocation between the vehicle and arm, rather than treating them only as disturbances.

0.40

Kinematic analysis of a double-closed-loop four-bar chain-based leg for a multimodal quadruped-pentarotor robot

cs.RO eess.SY ·2026-11-05 ·Prashant Raturi, Santhakumar Mohan
similarity 0.53
Abstract · Journal paper submitted to Robotica with ID:ROB-2026-0373

This paper presents the kinematic modeling and singularity analysis of a three-degree-of-freedom, double four-bar closed-loop quadruped leg mechanism. This leg is essential for transitioning between the two operational modes; therefore, it is examined in both joint and task spaces, leading to the development of its Jacobian matrix, which is vital for designing the gaits required for terrestrial mode and mid-air aerial reconfiguration (for aerial mode). Various gaits are devised for the system's motion in the MATLAB simulation, and their practical implementation on the single-leg test rig is demonstrated.

0.26

An Autonomous, 3D Printed, Waterjet-Powered, Open-Source Robotic Trimaran for Environmental Inspection and Monitoring

cs.RO eess.SY ·2026-10-05 ·Reuben O'Brien, Martin Lambrechtse-Reid, Minas Liarokapis
published similarity 0.53
Abstract · 8 pages. Accepted version. Published in the 2024 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS). Finalist for th…

Versatile, autonomous robotic boats can offer excellent environmental inspection and monitoring solutions for remote, dangerous, hard to reach, or access protected water bodies. This paper introduces such a platform in the form of an autonomous, cost-effective, waterjet-powered robotic trimaran. Motivated by the need for an efficient aquatic monitoring, particularly in Aotearoa - New Zealand's diverse environments, the trimaran provides an efficient, low-cost, and easy to replicate alternative to resource-intensive research vessels. The proposed platform, costs $600-1,500 USD to develop (depending on the sensing system configuration), weighs under 5 kg, and excels in bathymetry and water quality testing. The trimaran can reach speeds of up to 2 m/s offering obstacle avoidance of natural features, such as rocks. Utilizing off-the-shelf components and 3D printing technology, the proposed platform offers excellent reproducibility and robustness while operating in shallow waters with its jet propulsion system. The paper presents in detail the design characteristics, the sensing system employed, testing results focusing on bathymetry, and highlights the ability of vessel and the potential for future research and data collection.

0.58

Modeling and Control of an Eel-Inspired Soft Robot for Design Optimization

cs.RO ·2026-08-14 ·Zhangjingyi Jiang, Mark Campbell
published similarity 0.52
Abstract

Anguilliform locomotion is a highly efficient swimming mode; the advent of new materials for soft robots enables the development of an eel-inspired soft robot. This paper presents a simulation model of an eel-inspired soft robot designed for anguilliform swimming. This model can aid in design optimization and the development of model-based estimation, reasoning, and control systems. A Finite Element Method (FEM) model of an elastic rod is used to capture the soft materials of the robotic fish, which makes it particularly amenable to variation over time as the material properties change. The material model is coupled with a hydrodynamic force model to simulate the behavior of a soft, elongated robot in water. The model is used to demonstrate the effectiveness of the proposed control approaches in achieving desired swimming behaviors. It also provides insights into design decisions, including the robustness of different system configurations and the impact of material degradation and failure. The results show that slightly asymmetric designs are advantageous, offering comparable swimming velocities but greater maneuverability. This model can be used to guide future robotic design decisions aimed at optimizing performance for specific tasks.

0.56