CS Paper Radar

Fixed-mesh based approach for modeling of superconducting magnetic bearings

Elias Paakkunainen, Bárbara Maria Oliveira Santos, Gabriel dos Santos, Timo Tarhasaari, Paavo Rasilo, Sebastian Schöps

cs.CE cond-mat.supr-con ·submitted 2026-09-08 18:37 UTC · v1
code/dataunusual

Abstract

Numerical simulations of superconducting magnetic bearings (SMBs) are complicated by the relative motion between high temperature superconductors and the magnetic guideway, which commonly requires repeated updates of the geometry and mesh. We present a fixed-mesh based approach for modeling the motion induced effects in which a coordinate transformation is applied only to the air region between the moving regions. The transformation can be included in a time-dependent anisotropic material tensor, leaving the mesh during the simulation and the rest of the formulation unchanged. To provide numerical examples, the approach is implemented in 2D using the finite element method with the $j$-$a$ formulation and is combined with homogenization and circuit coupling for double-crossed loops of coated conductors. The open-source model implementations are made available. The proposed approach is verified and validated against existing modeling approaches and experimental results from the literature for SMBs. Two simulation examples are presented, and in both of them the levitation force predicted by the fixed-mesh model agrees with the experimental results, yielding $R^2$ values above 0.99. For a verification problem, it is shown that the fixed-mesh model converges towards the remeshed reference solution under mesh refinement as expected. For an SMB undergoing vertical and horizontal translations, the homogenized fixed-mesh model reproduces the lateral-force response of a fully resolved moving-geometry reference model. Additionally, the homogenized fixed-mesh model is computationally more efficient than the reference model, indicating a significant reduction in the number of degrees of freedom and the computation time. The results demonstrate accurate and computationally efficient simulation of translational motion with the fixed-mesh based approach.

Closest papers

Nearest neighbours by meaning across the whole index.

A Hierarchically Compressed Immittance Operator Formulation for Fast Statics-to-Full-Wave Electromagnetic Simulation with the Boundary Element Method

cs.CE physics.comp-ph ·2026-11-16 ·Shashwat Sharma
similarity 0.50
Abstract · 15 pages, 12 figures. Submitted to the IEEE Transactions on Antennas and Propagation

The boundary element method allows the electromagnetic simulation of three-dimensional problems with a two-dimensional discretization, using a surface integral representation of Maxwell's equations. For applications involving broadband simulations or multiscale geometries, the well-known low-frequency breakdown of conventional integral equation formulations must be addressed, while ensuring that dielectric, semiconducting, and lossy metallic regions are modeled rigorously, including the skin effect. In this work, a new boundary element formulation based on an immittance operator is proposed, where the underlying integral equations are inherently valid from statics to the full-wave regime. To enable efficient matrix assembly and solution, a hierarchical matrix compression strategy is devised, leveraging fast direct factorization as an intermediate step, and fast matrix-vector products for the iterative solution of the final system of equations. The proposed formulation is capable of electrostatic, magnetostatic, quasistatic, and full-wave simulations of dielectrics, semiconductors, and lossy metals. Representative numerical examples drawn from a variety of applications demonstrate the accuracy and efficiency of the proposed method.

0.30

Magflow: Differentiable Simulation of Industrial-Grade 6D Magnetic Levitation

cs.RO cs.LGeess.SY ·2026-11-17 ·Philipp Hartmann, Jannick Stranghöner, Klaus Neumann
top venuecode/data similarity 0.46
Abstract · 8 pages, 5 figures, 1 table. Accepted for publication in IEEE Robotics and Automation Letters (RA-L). Project page: https://sites.google.com…

Magnetic levitation with six-degrees-of-freedom enables frictionless transport and micrometer-scale positioning in principle, but low-level control is inherently challenging due to its complex and unstable dynamics. Industrial systems typically rely on deep hardware-software co-design, where mover and stator geometries are jointly designed to enable a compact, hand-crafted approximation of the electromagnetic force computation, thereby keeping control computationally tractable at kilohertz rates. However, this approach imposes overly conservative constraints on the operating workspace and the range of supported mover topologies. Instead of reducing the underlying physics to a hand-crafted approximation, we compute the physics directly. We introduce Magflow, a fully differentiable, GPU-parallel simulator for 6D magnetic levitation. It is used to train the first neural controller for an industrial-grade 6D magnetic levitation system that is learned purely from simulated physics. We show that the learned neural controller transfers zero-shot from simulation to real hardware while satisfying hard real-time constraints at 4 kHz. The learned controller achieves qualitatively new behaviors and even levitates a mover topology for which no hand-crafted solution exists. These results demonstrate that co-design is not a physical necessity for 6D magnetic levitation control. More broadly, control learning from simulated physics can find solutions beyond the reach of control engineering in demanding industrial domains. Source code and demonstration videos are publicly available at https://sites.google.com/view/magflow.

0.58

Extensible Programmatic Specification of Finite Element Methods

cs.MS cs.GRcs.PL ·2026-11-01 ·Theadora Fields Collin, Oded Stein, Gilbert Bernstein, Saman Amarasinghe
similarity 0.45
Abstract · 52 pages, 25 figures, including appendices

Finite element methods (FEMs) are a powerful and ubiquitous tool for solving engineering problems. Experimenting with different finite elements can improve the quality and efficiency of solutions. In some cases, the wrong (but nonetheless most common) choice of finite element will produce solutions which converge to the wrong answer regardless of mesh resolution. However, in practice, the choice of finite element is not explored due to the complexity of re-deriving and re-implementing finite element methods. Trying a new finite element is challenging because practitioners must manually deduce formulas to use these elements and implement them within a potentially complex system. We address this problem by introducing ElementForge, a finite element system that is parametric over the literate mathematical specification of a finite element in a domain-specific language (DSL). The ElementForge compiler reasons about tensor spaces, tensors, and tensor bases from first principles to derive implementations of finite elements. The ElementForge compiler is able to automatically derive implementations of finite elements previously only derived by hand. Further, ElementForge minimally couples several key mathematical concepts, mainly tensor fields, mesh topologies, sparse tensors, and assembled finite element operators, to produce a complete finite element system that is parametric over the choice of element. Consequently, the elements derived by the compiler can be applied parametrically to new meshes, PDEs, and boundary conditions. We evaluate our system by implementing several simulations with different finite elements, demonstrating that our system can explore tradeoffs in generality, accuracy, speed, and representational complexity. For example, we are able to implement the Morley, Bell, Argyris, and Hermite like elements with less than 50 lines of code and use them all in a single simulation.

0.29

Quasi-Helmholtz Calderón Multiplicative Preconditioning for Higher-Order Global Multi-Trace Integral Equations

cs.CE math.NA ·2026-09-15 ·Cedric Münger, Alessandro Zuccotti, Van Chien Le, Kristof Cools
similarity 0.43
Abstract

The paper presents a higher-order global multi-trace integral equation for time-harmonic electromagnetic scattering by composite objects. The higher-order multi-trace formulation is preconditioned with a Calderón multiplicative preconditioner using higher-order quasi-Helmholtz projectors. The higher-order quasi-Helmholtz projectors separate the solenoidal and non-solenoidal components of the basis functions. Separate access to the Helmholtz components circumvents the explicit inversion of an ill-conditioned mixed Gram matrix. This enables the application of Calderón multiplicative preconditioning without refining the mesh and resorting to dual basis functions. Furthermore, it enables low-frequency stabilization, as the solenoidal and non-solenoidal components can be rescaled individually. The higher-order quasi-Helmholtz projectors are computed iteratively, enabling iterative solvers to efficiently solve the preconditioned matrix system, yielding accurate solutions in a few dozen iterations. Numerical experiments are conducted for composite dielectric bodies, confirming the effectiveness of the proposed preconditioner for the global multi-trace formulation discretized with higher-order basis functions for dense meshes and at very low frequencies

0.10

Scaled boundary finite elements for FFT-based computational micromechanics

cs.CE math.NA ·2026-11-16 ·Flavia Gehrig, Carolin Birk, Matti Schneider
similarity 0.42
Abstract · 32 pages, 7 figures. Submitted to International Journal of Numerical Methods in Engineering

We introduce a matrix-free FFT-based solver for three-dimensional linear elastic homogenization problems discretized by the scaled boundary finite element method (SBFEM) on a voxel grid. Owing to its analytical solution in the radial direction, the SBFEM discretization is inherently softer than fully integrated voxel finite elements, whereas its displacement-based formulation remains symmetric, conforming, and supports arbitrary stiffness anisotropy. These properties make SBFEM an attractive candidate for porous and highly heterogeneous microstructures, where existing voxel-based FFT discretizations offer no generally reliable choice: Reduced-integration hexahedral elements, equivalently the rotated staggered grid discretization, may suffer from hourglass instabilities in the presence of voids, whereas fully integrated hexahedral elements are often too stiff. The proposed discretization uses hexahedral SBFEM cells on the full voxel mesh of a regular periodic grid, retaining the simplicity of a fixed-resolution voxel representation without requiring adaptive mesh coarsening. The main contribution is a preconditioner based on the homogeneous SBFEM stiffness operator. We show that this preconditioner may be applied locally in Fourier space and that the condition number of the preconditioned system is bounded by the material contrast, independently of the grid resolution. This result enables a fully matrix-free implementation of the SBFEM-discretized problem, without assembling or storing the global stiffness matrix. Numerical experiments on a short-fibre reinforced composite, a polyurethane foam and a sand-based binder jet microstructure demonstrate robust convergence and competitive accuracy compared with established voxel discretizations. In particular, SBFEM remains stable for porous microstructures, for which reduced-integration hexahedral elements become unstable.

0.29

HGTO: A Unified Graph-Based Physics-Informed Formulation for Structural Topology Optimization

cs.LG ·2026-09-14 ·Kangzheng Liu, Uday Kumar Punna, Leixin Ma
similarity 0.41
Abstract

Density-based topology optimization is typically structured as a nested sequence of material updates, structural analyses, and sensitivity assessments. While neural density parameterization and dual-field physics-informed approaches provide data-free alternatives, most existing methods represent density and displacement as coordinate fields and make limited use of the discrete relationships inherent in the finite element mesh. The present study introduces HGTO, a unified graph-based formulation that extends complete neural topology optimization from coordinate space to finite-element graph space. Element densities are parameterized on the element graph derived from the mesh, and the structural state is determined on the corresponding node--element hypergraph. Finite element kinematics, numerical quadrature, constitutive response, and force assembly remain explicitly defined operations within the differentiable computation. The material field and equilibrium state are therefore coupled through a common finite-element incidence structure. Numerical studies show compliance comparable to conventional density-based optimization at substantially lower computational cost than a representative coordinate-based dual-field neural method. The same coupled formulation accommodates high-resolution and irregular meshes, three-dimensional structures, finite deformation, and elastoplastic response.

0.46

A Geometrically Parameterized Quasi-Stationary 3D Model for High-Frequency Induction Tube Welding

cs.CE physics.comp-phmath.NA ·2026-09-10 ·Dmitry Ivanov, John Inge Asperheim, Bjørnar Grande, Prerana Das
code/dataunusual similarity 0.41
Abstract · 26 pages, 14 figures

A three-dimensional multiphysics finite element model for the simulation of high-frequency induction welding of tubes is presented. The model couples a time-harmonic $h-φ$ formulation with a stabilized quasi-stationary advection-diffusion heat transport equation, enabling accurate prediction of electromagnetic and thermal fields under industrial operating conditions. The model incorporates parameterized geometry generation and semi-automated, physics-tailored mesh construction and is implemented using the open-source tools GetDP and Gmsh. Validation against measurements from a commercial induction welding line for AISI 304 stainless steel tubes demonstrates good agreement with operating data. The validated model is subsequently applied to investigate the influence of impeder material by comparing a conventional FeNiZnV ferrite with the soft magnetic composite Ferrotron 559H for the induction welding of AISI 304 stainless steel tubes.

0.42

Planar-faced and high-Jacobian two-refinement hexahedral templates

cs.GR cs.CG ·2026-09-13 ·Hua Tong, Yongjie Jessica Zhang
similarity 0.39
Abstract

Automatically generating high-quality conforming hexahedral (hex) meshes from general input boundaries remains a challenging problem, despite the numerical advantages hex elements offer in simulation. Grid-based adaptive refinement, followed by hanging-node removal, is the most robust fully automatic choice. Among two-refinement methods, primal templates have better mesh quality than dual templates but depend on a strong balancing condition that over-refines the grid; neither family guarantees planar quadrilateral (quad) faces. This paper generalizes recent primal three-refinement templates to a two-refinement scheme under a moderate balancing condition, a relaxation of the strong one. 32 special and five fundamental patterns resolve all 144 symmetry-reduced configurations, followed by either a fast greedy algorithm or an integer linear programming (ILP) algorithm that trades extra runtime for a further reduction in element count. The scheme is the first two-refinement method in which all hexes have planar faces, and its meshes feed directly into a recent quality-guaranteed hex mesh reconstruction algorithm. At comparable element counts, it attains a similar Hausdorff ratio (HR) and a higher minimum scaled Jacobian (min SJ) than its three-refinement counterpart.

0.24