CS Paper Radar

A Geometrically Parameterized Quasi-Stationary 3D Model for High-Frequency Induction Tube Welding

Dmitry Ivanov, John Inge Asperheim, Bjørnar Grande, Prerana Das

cs.CE physics.comp-phmath.NA ·submitted 2026-09-10 08:46 UTC · v2
code/dataunusual

Abstract

A three-dimensional multiphysics finite element model for the simulation of high-frequency induction welding of tubes is presented. The model couples a time-harmonic $h-φ$ formulation with a stabilized quasi-stationary advection-diffusion heat transport equation, enabling accurate prediction of electromagnetic and thermal fields under industrial operating conditions. The model incorporates parameterized geometry generation and semi-automated, physics-tailored mesh construction and is implemented using the open-source tools GetDP and Gmsh. Validation against measurements from a commercial induction welding line for AISI 304 stainless steel tubes demonstrates good agreement with operating data. The validated model is subsequently applied to investigate the influence of impeder material by comparing a conventional FeNiZnV ferrite with the soft magnetic composite Ferrotron 559H for the induction welding of AISI 304 stainless steel tubes.

Comment
26 pages, 14 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Stray Losses in Power Transformers: A Comparative Study of Modeling Frameworks for Mild Steel

eess.SY ·2026-11-03 ·Micha Swaanen, Timo Overboom, Siamak Pourkeivannour, Tom Huiskamp, Guus Pemen
benchmarkunusual similarity 0.51
Abstract · 13 pages, 18 figures. Submitted to IEEE Transactions on Magnetics

Accurately predicting eddy-current and hysteresis losses in mild steel components such as the structural parts and tank of power transformers remains a challenge in transformer design. Conventional numerical approaches for eddy-current loss analysis require discretization at a fraction of the skin depth. While accurate, such fine volumetric mesh becomes computationally prohibitive for large power transformers. Moreover, hysteresis loss is not always included in this analysis. To investigate the trade-off between computational cost and accuracy, this work presents a comparative analysis of eight distinct modeling frameworks for predicting both eddy-current and hysteresis losses in mild steel. These include efficient methods avoiding meshing, such as standard impedance boundary conditions, and more accurate approaches retaining full volumetric meshing, namely complex permeability, nonlinear single-valued B-H curve, and Jiles-Atherton hysteresis modeling. To accurately represent the material's electromagnetic behavior, the properties of the mild steel used are measured directly from samples. Finally, loss measurements are conducted to benchmark all eight frameworks, demonstrating mean absolute percentage errors between predictions and measurements generally below 20%.

0.33

De-Risking Robotic Welding for In-Space Metal Joining Through Physics-Grounded Digital Twins

cs.RO physics.app-ph ·2026-10-15 ·Zhou Daniel Hao, Umer Masood Chaudry, Robert Shaw, Andrew Cheney, Nick Ludford +2 more
published similarity 0.43
Abstract · 14 pages, 7 figures. An alternative version was accepted for oral presentation at the 77th International Astronautical Congress (IAC 2026)

Growing interest in in-space servicing, manufacturing, and assembly has renewed attention on reliable metal joining for modular construction and on-orbit repair. Robotic welding is promising, but reduced-gravity and low-pressure operation remains poorly characterised and flight-like tests are limited. The UK Space Agency-supported ISPARK project is developing a physics-grounded digital twin for structured process de-risking. This paper evaluates a model-based prototype combining a finite-volume thermal weld-pool model, Gaussian-process (GP) and neural-network surrogates, and a simulated six-axis manipulator. The reduced model includes solid-liquid phase change, effective thermocapillary transport, and a local-pressure parameter. Gravity is assessed separately through a hydrostatic-to-capillary pressure ratio and does not enter the thermal energy equation. Across repeated five-fold cross-validation, the GP has lower normalised mean absolute error than the neural network for all eight outputs. In 10 held-out boundary cases, 74 of 80 solver responses fall within nominal 90% GP predictive intervals. A three-output GP query takes 249 microseconds, including scaling and predictive variance. In a simulated UR5 L-shaped-seam study, a proportional controller adjusts the synergic power-source setting as travel speed falls near the corner. Finite-volume re-evaluation finds all 12 closed-loop operating points and 9 of 12 open-loop points within an illustrative 1.0-3.0 mm root-side-width band. These simulation results support using the framework to screen welding conditions and control strategies before experimental tests. Thermal-vacuum, targeted reduced-gravity, and robotic hardware-in-the-loop studies are needed to assess the model and controller.

0.35

Extending high value components performances with Additive Manufacturing: application to naval applications

cs.CE ·2026-09-15 ·Matthieu Rauch, Gatien Pechet, Jean Yves Hascoet, Guillaume Ruckert
publishedhighly cited similarity 0.41
Abstract

Additive Manufacturing (AM), consists of depositing material in successive layers to obtain the desired part. The parts produced by AM can thus adopt geometries inaccessible by conventional manufacturing means, for example hollow or lattice structures which considerably reduce their weight while keeping or even improving their mechanical properties. Among the many existing processes, Wire Arc Additive Manufacturing (WAAM) is particularly well suited to the manufacture of large metallic parts. It is characterized by a supply of heat in the form of an electric arc (produced by a welding generator) and a supply of material in the form of wire. This paper will discuss the impact of additive manufacturing to enhance the performances of high value components, based on naval application: the manufacturing of a hollow propeller blade demonstrator of 1.5 m high realized in the laboratory.

0.66

Fixed-mesh based approach for modeling of superconducting magnetic bearings

cs.CE cond-mat.supr-con ·2026-09-08 ·Elias Paakkunainen, Bárbara Maria Oliveira Santos, Gabriel dos Santos, Timo Tarhasaari, Paavo Rasilo +1 more
code/dataunusual similarity 0.41
Abstract

Numerical simulations of superconducting magnetic bearings (SMBs) are complicated by the relative motion between high temperature superconductors and the magnetic guideway, which commonly requires repeated updates of the geometry and mesh. We present a fixed-mesh based approach for modeling the motion induced effects in which a coordinate transformation is applied only to the air region between the moving regions. The transformation can be included in a time-dependent anisotropic material tensor, leaving the mesh during the simulation and the rest of the formulation unchanged. To provide numerical examples, the approach is implemented in 2D using the finite element method with the $j$-$a$ formulation and is combined with homogenization and circuit coupling for double-crossed loops of coated conductors. The open-source model implementations are made available. The proposed approach is verified and validated against existing modeling approaches and experimental results from the literature for SMBs. Two simulation examples are presented, and in both of them the levitation force predicted by the fixed-mesh model agrees with the experimental results, yielding $R^2$ values above 0.99. For a verification problem, it is shown that the fixed-mesh model converges towards the remeshed reference solution under mesh refinement as expected. For an SMB undergoing vertical and horizontal translations, the homogenized fixed-mesh model reproduces the lateral-force response of a fully resolved moving-geometry reference model. Additionally, the homogenized fixed-mesh model is computationally more efficient than the reference model, indicating a significant reduction in the number of degrees of freedom and the computation time. The results demonstrate accurate and computationally efficient simulation of translational motion with the fixed-mesh based approach.

0.39

Scaled boundary finite elements for FFT-based computational micromechanics

cs.CE math.NA ·2026-11-16 ·Flavia Gehrig, Carolin Birk, Matti Schneider
similarity 0.38
Abstract · 32 pages, 7 figures. Submitted to International Journal of Numerical Methods in Engineering

We introduce a matrix-free FFT-based solver for three-dimensional linear elastic homogenization problems discretized by the scaled boundary finite element method (SBFEM) on a voxel grid. Owing to its analytical solution in the radial direction, the SBFEM discretization is inherently softer than fully integrated voxel finite elements, whereas its displacement-based formulation remains symmetric, conforming, and supports arbitrary stiffness anisotropy. These properties make SBFEM an attractive candidate for porous and highly heterogeneous microstructures, where existing voxel-based FFT discretizations offer no generally reliable choice: Reduced-integration hexahedral elements, equivalently the rotated staggered grid discretization, may suffer from hourglass instabilities in the presence of voids, whereas fully integrated hexahedral elements are often too stiff. The proposed discretization uses hexahedral SBFEM cells on the full voxel mesh of a regular periodic grid, retaining the simplicity of a fixed-resolution voxel representation without requiring adaptive mesh coarsening. The main contribution is a preconditioner based on the homogeneous SBFEM stiffness operator. We show that this preconditioner may be applied locally in Fourier space and that the condition number of the preconditioned system is bounded by the material contrast, independently of the grid resolution. This result enables a fully matrix-free implementation of the SBFEM-discretized problem, without assembling or storing the global stiffness matrix. Numerical experiments on a short-fibre reinforced composite, a polyurethane foam and a sand-based binder jet microstructure demonstrate robust convergence and competitive accuracy compared with established voxel discretizations. In particular, SBFEM remains stable for porous microstructures, for which reduced-integration hexahedral elements become unstable.

0.29

Noninvasive Anisotropic Identification of Magnetic Properties in Toroidal Shaped Magnetic Steel

eess.SY cond-mat.mtrl-sciphysics.app-ph ·2026-09-07 ·Xusen Qin, Reza Zeinali, Mitrofan Curti
unusual similarity 0.37
Abstract

This research proposes a model-free inverse approach for identifying the nonlinear anisotropic single-valued magnetic constitutive characteristics of soft magnetic materials from boundary measurements. Using the harmonic approximation, the internal magnetic flux density B and magnetic field strength H are independently reconstructed from the measured boundary data, thus avoiding the limitation of using a predefined parametric B--H mapping function. Subsequently, the reconstructed fields are spatially averaged along selected collection lines to recover the B--H characteristics of the principal directions. Numerical results demonstrate high reconstruction accuracy for unperturbed data and good robustness against Gaussian perturbations of the boundary measurements, with the overall mean error remaining below 5% for a 10% noise level. These results indicate that under the harmonic-field assumptions, the field-based reconstruction provides a simple and computationally efficient framework for non-invasive identification of nonlinear anisotropic magnetic constitutive characteristics.

0.26

Transient multimode heat transfer of an industrial automated tape laying process under rapidly changing conditions

cs.RO ·2026-08-26 ·Bernhard Rameder, Hubert Gattringer, Andreas Müller, Ronald Naderer
publishedunusual similarity 0.37
Abstract · 20 pages

This work presents a transient heat-transfer model of an industrial automated tape laying (ATL) process designed to overcome the limitations of conventional thermal models in composite manufacturing. The model solves the heat-conduction equation with coupled advection, conduction, convection, and radiation. A key innovation is the implementation of an analytical view factor approach that accounts for finite emitter and tape widths, thereby correcting systematic overestimations of radiative heat flux inherent in 1.5D simplifications. Furthermore, a local convection assessment incorporates mixed convection effects characterized by the Richardson number, ensuring accuracy across a wide range of process speeds. The ATL system is represented by two interacting subsystems: the moving tape substrate and the infrared heat sources. The tape is discretized using a two-node model that resolves the physical phase shift between the heated and monitored surfaces. Numerical stability under high dynamics is ensured by a monolithic solution strategy using a high-order implicit integration scheme. Model predictions were validated on an industrial ATL line, demonstrating an overall deviation of only 1.08% (NRMSE) under rapid velocity and current modulations. This framework provides a high-fidelity, physics-based foundation for thermal state estimation, supporting consistent in-situ consolidation and improved part quality.

0.42

ALETHEIA: A Multi-Frequency Eddy Current Pulsed Thermography Dataset for Neural Operator Learning in Nondestructive Testing

cs.LG ·2026-11-08 ·Changbin Sun, Jie Xiao, Xiaotian Chen, Yuankai Wu
benchmarkdatasetcode/data similarity 0.37
Abstract · 62 pages, 19 figures

Learning neural solvers for spatiotemporal partial differential equations (PDEs) under real-world constraints remains a key challenge in scientific machine learning, especially for inverse tasks with sparse and noisy boundary observations. We present the Aletheia dataset, the first 3D benchmark for learning data-driven solvers in the context of nondestructive testing (NDT). The dataset simulates eddy-current-induced heating in conductive solids and models the resulting transient heat propagation governed by the heat equation. Aletheia contains over 4,700 high-resolution samples across 10 excitation frequencies (1-100,kHz), each providing volumetric heat source and temperature fields over time. It supports both forward prediction of temperature evolution and inverse reconstruction of internal heat sources or defects from surface infrared measurements. Real infrared thermography data from cracked rail specimens are included for calibration and comparison. We define four canonical tasks on both regular and irregular grids and benchmark them using various neural operators. Aletheia establishes a unified platform for evaluating neural PDE solvers under realistic NDT conditions, enabling progress in reliable, data-driven inverse modeling. The dataset and code are publicly available at https://github.com/sherlock-0327/ALETHEIA.

0.42