CS Paper Radar

Gait-Dependent Effects on Quadruped Locomotion for Load-Carrying using Passive Mechanism

Giovanni B. Dessy, Claudio Semini, Victor Barasuol

cs.RO ·submitted 2026-09-10 04:05 UTC · v2

Abstract

Passive mechanical interfaces offer a lightweight alternative to actuated manipulators for quadruped payload carrying, but their impedance directly couples the payload dynamics with the locomotion pattern. This paper analyzes how passive-arm stiffness-damping selection affects payload-carrying locomotion under different gait and payload conditions. We compare damped and underdamped passive-arm impedance configurations in simulation during flat-ground locomotion. For crawl gaits, where the support polygon remains well defined, the results show that underdamped impedance increases passive-joint oscillations and can reduce the ZMP margin with respect to the support polygon. Trot is retained as a dynamic excitation case for the passive arm, but it is not used for direct ZMP-margin stability comparison. The results are summarized in gait-payload-stiffness-damping maps, where ZMP-margin reduction is evaluated for crawl gaits and trot is retained only as a passive-arm excitation case.

Closest papers

Nearest neighbours by meaning across the whole index.

When to Waddle: A Comparative Study of Bipedal Torso-Stabilization on Low-Friction Surfaces

cs.RO ·2026-09-18 ·Ben Gu, Naomi Oke, George Ortiz, Stacy Ashlyn, Cordelia Pride +2 more
similarity 0.65
Abstract

Low-friction surfaces challenge bipedal locomotion by limiting the contact forces available during stepping. Inspired by penguin waddling, we investigate how lateral torso motion and center of mass (COM) placement affect locomotion as surface friction changes. Using a five-actuator biped, we compare an upright-gait strategy with a penguin-inspired torso-over-stance-leg strategy across multiple COM placements in simulation and hardware. In the 3-D simulator MuJoCo, we sweep through sinusoidal leg and hip actuation parameters across four friction coefficients mu = 0.1, 0.3, 0.5, 0.7. In simulation, torso-over-stance-leg motion produces more successful controllers and higher forward speeds at low friction, with the highest speed occurring for the high-COM configuration. Hardware experiments show the same low-friction speed trend: at mu=0.12, torso-over-stance-leg motion increases forward speed and reduces cost of transport at both tested COM ratios, and the higher COM also improves both measures. The high-COM penguin configuration is the fastest and most energy efficient while maintaining low sideways foot motion. At mu=0.45, the COM trend reverses: the lower-COM configurations are faster and more energy efficient, while gait strategy has little effect on forward speed but still changes sideways foot motion. These results show that the effects of lateral torso motion and COM placement depend on the available friction, and that forward speed, energy use, and slip-related foot motion can be modulated with a penguin-inspired torso motion on hardware.

0.22

Spiderbot: An Open-Source Energy-Efficient Hexapod with Passive Gravity Compensation

cs.RO eess.SY ·2026-09-22 ·Ritwik Sharma, Vimarsh Shah, Saransh Agrawal
code/data similarity 0.65
Abstract · 8 pages

Hexapod robots can achieve static stability with fewer actuated joints than bipeds or quadrupeds, yet many platforms still use 3-DOF legs, increasing weight and continuous torque requirement with limited gain in locomotion capability on flat, inclined and moderately rough terrains. We release Spiderbot, an open-source hexapod that uses a 4-bar linkage with a passive spring to mechanically support body weight, with a 2-DOF per-leg design that substantially reduces energy consumption. This mechanism substantially offloads gravitational torque during standing stance consuming only 1.5W (reduction of over 90\% over the unsprung version and up to 96\% over other similar hexapods). The passive spring compensation extends to payloads of up to 3.25kg with no additional torque requirements. The platform enables long-duration deployments on a modest battery budget and costs under \$400, making it suitable for large-scale multi-agent experiments. We validate the locomotion capabilities of the platform with an RL policy trained in mjlab, including successful sim-to-real transfer, despite the complexity of the mechanism. The platform is evaluated on flat and rough terrains, slope up to $15^\circ$ and step obstacles. We release all the CAD files, assembling instructions, and full training and deployment code along with the model checkpoints at https://erc-bpgc.github.io/SpiderBot/.

0.27

Exploring Nonlinear Body Oscillations for Natural Quadruped Gaits

cs.RO ·2026-09-01 ·Annika Schmidt, Davide Calzolari, Arne Sachtler, Florian Loeffl, Daniel Seidel +11 more
similarity 0.63
Abstract

Animals' body morphology shapes the gait patterns they can perform, where mechanical resonance reduces the need for active control. By tuning posture and muscle stiffness, they leverage their embodied intelligence to achieve effective gaits for different speeds. In contrast, most quadruped robots are not specifically designed to exploit mechanical resonance due to the complexity of nonlinear dynamics and require dedicated locomotion controllers. To provide an alternative, we present a proof of concept framework making the nonlinear dynamics of a robot predictable in the design process and show how this knowledge can be leveraged such that multi-gait locomotion can emerge from nonlinear resonances, shaped by gravity, inertia, and elasticity. We present the highly compliant quadruped robot eBert, on which we identify six nonlinear normal modes (NNMs) using our new theoretical tools and validate their existence in simulation and hardware. With black-box optimization to determine step length, simulations show how each NNM naturally develops into a distinct gait, manifesting different speeds, which also largely transfers to the robotic hardware. Our experiments show that eBert can exploit its mechanics to generate task-specific movements which may serve as foundation for designing a new generation of agile and efficient robots leveraging embodied intelligence.

0.26

Hip Energized Monopedal Hopping

cs.RO ·2026-08-11 ·Shane Rozen-Levy, Griffon McMahon, Daniel Koditschek
similarity 0.60
Abstract · 35 pages, 11 figures

We present a novel stepping strategy for pitch unlocked planar monopeds where the reaction torques from stabilizing pitch with a conventional PD + feedfoward controller are recruited to counteract energetic losses from damping. By moving the location of the mass center, our controller increases the pitch stabilization torque, thereby adding energy to the gait. A new stepping policy adjusts the distribution of energy between the radial and angular degrees of freedom to counteract dissipative losses and achieve a user specified balance between steady state fore-aft speed and apex height. Hybrid averaging analysis yields closed form expressions for the fixed points and eigenvalues of the resulting gait, lending insight into the interplay between the physical and control parameters' influence on performance. Simulation studies on a generic 5 link biped and a careful model of the Penn Jerboa reveal a useful correspondence to these analytical predictions. Physical experiments on the Penn Jerboa exhibit stable locomotion with speeds ranging from 1.02 m/s to 1.77 m/s (5.10 leg lengths/s to 8.85 leg lengths/s) in a manner effectively approximated by the mathematical analysis.

0.10

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.59
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14

Design and Analysis of a Nonlinear Parallel Mechanism Coupling for Dynamic Humanoid Legs

cs.RO ·2026-10-12 ·Rohit Kumar, Heiner Peters, Felix Wiebe, Franek Stark, Janne Janzen +3 more
similarity 0.58
Abstract

Humanoids increasingly demand lightweight leg mechanisms for agile, dynamic, and energy-efficient locomotion. Reducing distal inertia through proximal actuation has thus become a common design goal. Yet, compact transmissions that preserve torque capability and efficient force transmission remain hard to achieve. This paper presents a novel series-parallel leg design combining a knee parallel mechanism, an ankle parallel mechanism, and a nonlinear knee-ankle coupling where all actuators placed closer to the hip. As the knee flexes, the coupling passively assists ankle dorsiflexion for foot clearance and, as it extends it assists plantarflexion for push-off, redistributing ankle load through the knee transmission. We derive the coupling's nonlinear transmission models and validate them in simulation and on hardware. The design shows that the shared transmission lets both joints draw on each other's actuator capacity by easing the knee's peak torque demand under load and the ankle's peak speed demand during fast motion. With the leg's proximal actuator placement, the leg achieves an effective reflected mass of 0.37 kg at the foot for a 6 kg leg, demonstrating very low distal leg inertia for dynamic humanoid robots.

0.12

Breaking speed scaling in quadrupedal robots via Huygens' coupled-pendulum dynamics

cs.RO ·2026-09-09 ·Yucheng Tao, Yongbin Jin, Shaowen Cheng, Xianwei Liu, Yanyan Yuan +6 more
similarity 0.58
Abstract

Achieving biological-level running speeds has largely been pursued through advances in control algorithms, which improve the utilization of existing hardware. However, the ultimate speed limits remain governed by the underlying force and torque requirements of rapid locomotion, which are typically addressed through increased actuator capacity. Inspired by Huygens' coupled pendulums, we demonstrate that superior locomotion can emerge from principled exploitation of intrinsic dynamics rather than brute-force hardware scaling. Inter-limb inertial coupling redistributes energy across the gait cycle and reduces peak joint torque required for rapid periodic motion, thereby expanding the achievable speed without proportional increases in actuator capability. Incorporating hardware parameters as additional design variables further extends this analysis into a co-optimization framework, enabling the systematic utilization of inertial coupling in robot design. Guided by this framework, a quadruped robot achieves a running speed of 10.74 m/s (Froude number 21.4) and completes a 100-meter sprint in 12.2 seconds, representing the first legged robot to surpass 10 m/s. These results establish inertial coupling as an underlying mechanism governing high-speed legged locomotion and highlight its role in reducing force requirements, offering new insights into the design of agile robotic systems.

0.24

Optimized Wrench Polytope Analysis for Real-Time Stability Control of Legged Robots in Complex Multi-Contact Configurations

cs.RO ·2026-09-15 ·Friedrich Graaf, Elias Birkefeld, Christian Eichmann, Elias Hofele, Tristan Schnell +3 more
similarity 0.57
Abstract · 8 pages, 8 figures, submitted to the IEEE ROBIO 2026 Conference

Legged robots offer a variety of automation applications in real-world scenarios. But areas that are difficult to traverse, like slopes, caves, or scaffolding, still pose a great challenge for traversal. To tackle this problem, we propose an optimized algorithm for evaluating the full actuatable wrench polytope for arbitrary contact scenarios. With our improved analysis algorithm, the torques for each joint of the robot can be calculated within a control frequency of 49 Hz. The achieved speedup allows for deployment within a regular control loop for actuating robot poses for different contact scenarios. We evaluated our stability controller extensively in simulation scenarios and validated its applicability by deploying it on actual walking robot hardware. The proposed controller achieved stability in very complex scenarios that are currently not achievable by any other controller.

0.29