CS Paper Radar

Low Clearance Hinge Joint Mechanism Based on 3D Printing on Sheet Fabrication Methodology

Jaehyung Jang, Euibin Shin, Allison M. Okamura, Jee-Hwan Ryu

cs.RO ·submitted 2026-09-14 09:35 UTC · v1

Abstract

This paper presents a low-clearance hinge joint mechanism based on the 3D printing on sheet fabrication method. This approach simplifies the fabrication of hinge mechanisms and overcomes limitations of conventional origami manufacturing by eliminating the need for adhesives commonly used during assembly, making it suitable for robots at the tens-of-centimeters scale. The advantages and disadvantages of three types of hinge joint mechanisms are compared, and a hinge joint that can be designed with low clearance for various facet thicknesses is selected. Based on the selected hinge joint, the twisting angle and bending force are analyzed, leading to the implementation of a clearance of 0.1 mm. Torsional resistance is experimentally evaluated to measure the torque required for twisting caused by plastic deformation and clearance. The results show that the torque associated with plastic deformation is sufficient to constrain the undesired degrees of freedom of the hinge joint, while the torque required for twisting due to clearance is minimal. Based on the analyzed data, the proposed hinge joint mechanism is applied to a 3-degree-of-freedom delta robot manipulator, demonstrating precise motion with low clearance.

Comment
5 pages, 8 figures

Closest papers

Nearest neighbours by meaning across the whole index.

One Print, Many Moves: Monolithic Origami-inspired Folding Actuator for Composable Soft Multi-DoF Systems

cs.RO ·2026-09-01 ·Jaehyung Jang, Zhenish Zhakypov, Jasmin Elena Palmer, Melissa Klein, Jee-Hwan Ryu +1 more
similarity 0.59
Abstract · 26 pages, 7 figures

Conventional soft robot actuators excel in compliance, but their uncontrolled deformations compromise accuracy and hinder scaling to multi-degree-of-freedom (DoF) systems. We introduce a MONOlithic ORIGAMI-inspired soft folding actuator design (MONORIGAMI) that establishes a design strategy based on spatially programmed stiffness anisotropy to preserve material compliance along desired folding directions while selectively restricting deformation in unwanted directions. The actuator leverages stiffness tiers based on material thickness, patterned in an origami-inspired geometry with facets and creases, converting unconstrained soft deformation into accurate, repeatable, and composable folding motions without additional reinforcements. The design is fully 3D-printable through a single-material, single-print process that requires no assembly. Each actuator serves as a scalable motion primitive, and linking and orienting multiple actuators mechanically programs multi-DoF trajectories. Using the same fundamental module, we demonstrate three 3D-printed soft multi-DoF robotic systems spanning distinct application domains: (1) a compact 4-DoF wearable haptic device for high-fidelity cutaneous feedback in virtual reality (VR), (2) a 3-DoF joystick for kinesthetic feedback in teleoperation, and (3) a modular robotic gripper capable of underwater operation with geometry-encoded grasp trajectories. These systems demonstrate the module's capabilities for compact multi-axis integration, controlled physical interaction, and geometry-programmed operation across different environments. Together, these results show that MONORIGAMI provides a general, composable, accessible, reliable, and scalable platform for high-precision soft multi-DoF robotics, addressing long-standing limitations in both soft actuator design and fabrication.

0.14

Modular fabrication and design of thick rigid-foldable origami metamaterials

cs.CE ·2026-08-20 ·Sunao Tomita, Hiroki Kobayashi, Shoko Arita, Masato Tanaka, Atsushi Kawamoto +2 more
similarity 0.57
Abstract · 20 pages, 5 figures

Origami metamaterials offer significant potential for stiff deployable structures However, fabricating load-bearing cellular structures from thick panels introduces geometric interference at non-manifold junctions. Conventional thick-panel fabrication often disrupt ideal kinematics, thereby compromising smooth motion and scalability. This study proposes a modular fabrication framework that preserves one-degree-of-freedom rigid-folding kinematics in thick and non-manifold origami metamaterials. By decomposing non-manifold junctions into a hierarchy of stacked, modular hinged panels, our approach successfully accommodates synchronized hinge motions using scissor-like linkages. Exploiting this representation, we implement a graph-based topology optimization framework that tailors macroscopic stiffness while preserving folding connectivity. We demonstrate this approach by fabricating optimized prototypes that deploy seamlessly with a one-degree-of-freedom motion. Furthermore, we demonstrate engineering scalability through the large-scale construction of extensive deployable systems assembled from modular panels, which exhibit high load-bearing capacity. These results pave the way for the practical fabrication of structural, large-scale deployable metamaterials.

0.28

Flexible-body Modeling, Kinematic Identification, and Assembly Accuracy of Overconstrained Spatial Linkages

cs.RO math.AG ·2026-09-15 ·Daniel Huczala, Michael Pieber, Johannes Gerstmayr, Andreas Mair, Frederik Schulte +4 more
similarity 0.56
Abstract

Overconstrained rational single-loop linkages are efficient, compact, and low-cost custom mechanisms, yet their deployment in industrial settings is limited. In simulations, rigid body formulations fail due to redundant constraints. This study presents a flexible multibody modeling framework based on the floating frame of reference formulation, and delivers an overall accuracy analysis of assembled linkages prototypes. The approach is validated against 3D-printed PLA prototypes of a Bennett four-bar mechanism, including variants with intentional joint-axis misalignment, which theoretically, from the rigid body point of view, cannot be assembled. A supplementary contribution is delivered in the form of a kinematic parameter identification methodology suited for this type of mechanism with ill-conditioned Jacobian. The experimental and simulation results are compared and reveal that these overconstrained mechanisms exhibit a self-assembling tendency -- structural compliance drives the assembly toward the ideal geometric configuration, distributing constraint stress throughout the structure. Additional qualitative demonstrations using cardboard tubes and bamboo sticks as link building blocks confirm that functional mechanisms can be realized from low-cost, unconventional materials with limited manufacturing accuracy. The proposed modeling pipeline is fully algorithmic and enables design optimization in the future.

0.18

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.53
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14

PHD-Hand: A Printable Humanoid Dexterous Hand with Linkage-Driven 3-DOA Digits

cs.RO cs.AI ·2026-10-21 ·Neel Adwani, Muhaiminul Islam Akash, Saffia Ouali, Ethan Liu, Cong Wang
published similarity 0.52
Abstract · Submitted and Accepted at IEEE-RAS International Conference on Humanoid Robots (Humanoids 2026). 8 pages. Supplementary video: https://lnkd.…

Currently, dexterous humanoid robot hands are widely considered the final hardware bottleneck that hampers generalist robots from physically assisting people at home and work. As conventional tendon-driven designs suffer from high cost, demanding maintenance, poor reliability, and short durability, alternative linkage-driven designs have increasingly gained attention. Despite their potential to avoid the weaknesses of tendon-driven hands, integrating multiple degrees of actuation (DOA) in a single digit with linkage drivetrains is a challenge for design and fabrication. Only a few studies have managed to present functional humanoid hands that are completely linkage-driven and have at least three DOAs per digit without compromising actuator placement and other design preferences. Our work introduces a new linkage-driven hand featuring a unique flexure hinge. Together with elastic drive rods made of spring steel, the linkage drivetrains are significantly simplified. Unlike other linkage-driven designs of similar dexterity, our design does not require many miniature moving parts. As a result, the hand can be fabricated easily with a budget 3D printer. This not only significantly lowers the barrier to entry for using and developing dexterous humanoid robot hand functions, but also allows the hands to be sized much closer to regular human hands. The design offers desirable kinematic advantages as well. A prototype is evaluated for grasping and object manipulation. In addition, this paper presents our latest findings on kinematics and control of the hand.

0.25

Suspended-Fabric Robotic Manipulation Surfaces: Modelling, Design Space, and Multimodular Extensio

cs.RO ·2026-10-30 ·Pratik Ingle, Jørn Lambertsen, Kasper Støy, Andres Faiña
similarity 0.51
Abstract

Robotic Manipulation Surfaces (RMS) reposition objects by deforming the surface on which they rest. A recent class of RMS suspends a continuous fabric sheet from a sparse grid of vertical linear actuators lowering the actuator density of such surfaces but how to design such surfaces so that objects can be controlled everywhere on it, and how to extend it beyond a single module so that objects can pass between modules and achieve parallel, remain open. This paper presents a separable catenary model of the suspended sheet that is fast to compute and provides both the surface shape for given actuator heights and the actuator heights for a desired local slope. The closed form inverse lets a simple PID controller position objects on the sheet, and the model relates fabric length, module span and actuator stroke to the reachable workspace, yielding a minimum fabric length bound and design charts for these surfaces. The approach is then extended to a multimodular platform in which neighbouring modules share actuators. On a $2 \times 2$ prototype, we demonstrate that centimetre-scale objects are transferred between modules and positioned within 0.03 m over a $1 m^2$ workspace with only nine actuators, enabling multi-object manipulation and opening the way to parallel manipulation.

0.21

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.51
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Design and Experimental Validation of a 3D Printed Torsional Series Elastic Actuator for Safe Human Robot Interaction

cs.RO ·2026-09-16 ·Joel Hidalgo Pisco, Melissa Cobos Condo, Luigi Miranda, Dennys Paillacho
published similarity 0.51
Abstract

Ensuring intrinsic safety in physical human robot interaction (pHRI) is a critical requirement for social and service robots. While Series Elastic Actuators (SEAs) offer hardware based compliance, traditional metallic designs often require complex, multi part assemblies. This paper presents the design, finite element analysis (FEA), and experimental validation of a low stiffness, torsional spring for SEAs, manufactured via 3D printed thermoplastic polyurethane (TPU). The compliant element exhibits a highly linear torque deformation response (Ks = 0.066 Nm/degree), matching numerical predictions with under 3% deviation, a variance attributed to FDM structural anisotropy. To accommodate external interactions using standard position limited servomotors, a hybrid position controller with torque threshold switching was implemented. Experimental evaluations demonstrate the system ability to accurately track non stationary trajectories and safely yield to external disturbances. Furthermore, the inherent material damping of the TPU acts as a passive low pass filter, preventing high frequency oscillations during control mode transitions. The proposed architecture offers a cost effective, reliable, and easily manufacturable solution for safe pHRI.

0.32