CS Paper Radar

Geometric Shortcuts for Complex Trunk Postures: Dual-Helicity Coupling Enables Low-Dimensional Control

Huishi Huang, Danlu Chen, Matteo Lo Preti, Jun Liu, Marcelo H. Ang, Cecilia Laschi

cs.RO ·submitted 2026-09-16 02:54 UTC · v2

Abstract

How do elephant trunks generate complex postures without relying solely on fine segmental activation? We propose that part of this complexity arises from a low-dimensional geometric shortcut: dual-helicity coupling between opposite-handed oblique muscles. In a simplified soft-robotic prototype, varying only two geometric parameters generates a broad library of elephant-like postures, suggesting a dual-layer control architecture with implications for continuum robot design and biological hypotheses.

Closest papers

Nearest neighbours by meaning across the whole index.

Dynamic Shape Control of Soft Trunk Robots

cs.RO ·2026-11-04 ·Hehui Zheng, Marc Stampanoni, Roshan S. Kaundinya, Ronan Hinchet, George Haller +1 more
similarity 0.62
Abstract

Controlling the shape profile of soft trunk robots extends their reach into complex regions of the workspace and enhances their use in practical applications. Recent advances in soft robot design have enabled soft trunk robots to achieve greater flexibility in conforming to complex shapes. Specifically, trunk robots whose geometries are designed as helicoids have been shown to enable extreme shape-changing capabilities. Their compliance makes them highly nonlinear, which in turn makes shape control difficult. On similar tendon-driven trunk robots, model-based controllers based on the theory of adiabatic spectral submanifolds (aSSMs) have achieved high accuracy in closed-loop end-effector tracking. We extend this approach by learning an aSSM model of the full body of a trimmed-helicoid soft trunk robot from data and use this in a model predictive control (MPC) scheme to demonstrate a range of shape control tasks on hardware. On closed-loop dynamic shape regulation, our method outperforms the available linear baselines by a factor of 10. In human-in-the-loop interactive demos, our method completes section-by-section shaping and balances a tennis ball for over 25 seconds, while the linear baselines fall short. A model-free reinforcement learning policy trained for 12 hours on hardware fails on the same balancing task. These results establish aSSM-based MPC as a practical route to full-body shape control on real soft hardware.

0.21

Tensegrity Continuum Robots Enable Task-Adaptive Morphologies for Cooperative Behaviors

cs.RO ·2026-08-27 ·Mahmud Hasan Saikot, Sydney Spiegel, Sudheera Akalanka Kariyawasam, Andrew Stefka, Josh Chrisler +1 more
top venue similarity 0.60
Abstract · 22 pages, 6 figures, Accepted to Nature Machine Intelligence

Robots that can change their morphologies and behaviors for different tasks and environments hold great promise for adaptable, multifunctional systems. Modular reconfigurable robots (MRRs) can achieve such functionalities by docking and rearranging individual units, but most rely on rigid modules that lack structural compliance, resulting in limited capabilities. Continuum robots offer compliance through flexible backbones, yet they cannot self-reconfigure into task-adaptive multi-robot configurations. Here, we introduce an MRR that unifies the advantages of both architectures by combining a tensegrity-based compliant body with claw-based connection mechanisms. Each robot can manipulate and locomote independently, and multiple robots can self-reconfigure into different morphologies (e.g., chains, loops, branches) for cooperative manipulation and locomotion. We demonstrate the robots' capability across diverse tasks and environments, including coordinated object manipulation and transport, multimodal locomotion, and loco-manipulation in real-world scenarios. These results lay a foundation for adaptable and multifunctional robotic collectives, with broad potential applications in manufacturing, space exploration, and search-and-rescue operations.

0.34

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.59
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Estimation and Control of Tensegrity Manipulator Kinematics based on Strut Inclination Angles

cs.RO ·2026-09-21 ·Tufail Ahmad Bhat, Shuhei Ikemoto
top venue similarity 0.57
Abstract

Unlike conventional rigid-link robots defined by discrete joints, continuum robots pose a fundamental challenge for expressing their complex continuous bending configurations for closed-loop control. Several modelling approaches have been proposed for conventional continuum robots, but tensegrity-based continuum robots remain largely open. Moreover, many of these approaches assume a continuous elastic backbone and are therefore not directly applicable to tensegrity manipulators, whose bodies are networks of rigid struts and tensioned cables. This work presents a reduced-order model for shape and posture control of a tensegrity-based continuum manipulator. The manipulator is modelled as a serially connected parallel-link mechanism. The proposed method is formulated as an optimization problem that uses geometric constraints of the tensegrity structure together with information from the Inertial Measurement Unit (IMU) sensors embedded in the strut elements. To the best of our knowledge, this work presents the first experimental demonstration of a real-time IMU-based shape estimation method on a full-scale tensegrity manipulator and demonstrates posture control using a simple Proportional-Integral (PI) controller. The results show that the proposed method can estimate the shape of both single-module tensegrity structures and multi-module tensegrity manipulators from arbitrary static configurations and achieve desired postures.

0.48

Adaptive Bendpoint Formation in Octopus-Inspired Soft Continuum Arms

cs.RO ·2026-10-18 ·Jessica Gumowski, Julian Finn, Krishna Manaswi Digumarti, David Howard
similarity 0.56
Abstract

Octopuses exhibit a powerful form of embodied intelligence from a highly adaptable soft body. One key mechanism is the ability to instantiate bending points at any location along the arm, which enables performant and dexterous behaviours. Taking inspiration from the octopus for its dexterity, this study focuses on changing the curvature of a tendon-actuated arm by adaptively changing the anchoring end-point along the arm. An array of inflatable shells is integrated into the arm, where inflating a shell causes an increase in friction at the location, jamming the tendon and creating a temporary new anchoring point. The novel soft actuator does not break the continuity of the arm between the actuated segment and the loose segment. Experiments show that the actuated segment has a non-constant bell-shaped curvature which is comparable to that of a real octopus arm during a reaching motion. Compared to conventional single-tendon continuum manipulators, the proposed design offers an expanded workspace and enhanced dexterity through the ability to independently shape different regions of the arm through selective curvature tuning. At the same time, it avoids the mechanical complexity typically associated with multi-segment, multi-actuator systems.

0.14

Riemannian Optimization-based Whole-body Obstacle Avoidance for Mobile Continuum Robots in Cluttered Environments

cs.RO ·2026-11-04 ·Duo Tang, Ping Deng, Sophie Armanini, Yajing Shen, Toshio Fukuda +2 more
similarity 0.55
Abstract

Inspired by the coordination of global motion and local shape adaptation in snakes, elephant trunks, and octopus arms, we propose a unified planning and control framework for mobile continuum robots in cluttered and confined environments. Existing approaches often address high-level path planning and local motion control separately, limiting coordinated base-arm motion, kinematic consistency, and collision avoidance. Our framework integrates long-horizon trajectory planning with real-time geometric refinement under kinematic and environmental constraints. The global layer combines A* search with minimum-jerk planning to generate smooth reference trajectories. The local layer uses a geometry-consistent inverse kinematics solver and Riemannian optimization to coordinate mobile-base motion and continuum deformation while avoiding obstacles. We evaluate the framework through simulated pipe-traversal tasks with multiple baseline planners and real-world experiments involving navigation among dense obstacles and manipulation in confined spaces. Results demonstrate improved motion consistency, feasibility, and adaptability, supporting coordinated whole-body motion of mobile continuum robots in constrained environments.

0.27

A Multi-Vine Soft Robot Enabling Accessible Working Channel and Steering

cs.RO ·2026-09-03 ·Reza Kashef, Cem Suulker, Mohammad Sheikh Sofla, Kaspar Althoefer
published similarity 0.55
Abstract · Hamlyn Symposium on Medical Robotics 2026

Soft eversion robots, also known as vine robots, have attracted growing interest for navigation and inspection tasks, including minimally invasive medical applications [1]. A vine robot consists of a thin, flexible, inextensible tube folded inward that everts and grows forward when pressurized. This tip-growth enables navigation with minimal friction, making vine robots well suited for complex environments such as the human colon [2]. While their inherent softness allows passive conforma- tion to curved pathways in confined spaces, navigation performance strongly depends on environmental inter- actions, including contact angle and the length of un- constrained deployed material [3], [4]. Sharp directional changes, such as those in the sigmoid colon, often limit passive growth and necessitate active steering. Existing solutions include distributed artificial muscles [5] or dedicated tip-based steering mechanisms [6]. In addition, many applications require payload delivery, such as sensors and tools [7], [8]. Within the ERC Synergy project EndoTheranostics, this motivates the development of vine robots capable of delivering micro- surgical tools during growth. Prior work has integrated working channels within the vine body [8], [9], but these approaches constrain tool size, introduce friction, and limit access to the environment to the robot tip. In this work, we propose a multi-vine architecture in which two vine robots are coupled to an externally integrated working channel via soft mounting tips [10]. Independent vine actuation enables active tip steering while advancing the working channel without embed- ding it within the vine bodies Figure 1. Experiments demonstrate sharp steering of nearly 90 degrees during growth, highlighting the potential of this architecture for versatile medical and non-medical applications.

0.35

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

cs.RO ·2026-09-21 ·Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin +8 more
similarity 0.54
Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

0.38