CS Paper Radar

Blind IRS Beamforming Using Only Received Signal Power Measurements

Tao Wang, Xiaohui Zhang, Pengfei Lv, Hehe Ban, Yiwei Guo, Ming Yi

eess.SP ·submitted 2026-09-30 03:20 UTC · v1
published

Abstract

This paper proposes a novel blind beamforming strategy for signal enhancement aided by an intelligent reflecting surface (IRS), using only samples of the received signal power. Unlike existing conditional sampling mean (CSM) based approaches, which rely solely on comparing the CSM values, the proposed algorithm fully exploits the information in the sampled data by constructing a least squares problem. This enables the estimation of the phase difference between the IRS-reflected channel and the direct channel, ultimately yielding the optimal IRS phase configuration. The simulation results verify that, by fully leveraging the collected data, the proposed scheme outperforms the CSM-based method, especially when the number of IRS phase quantization levels is larger than 2, while incurring the same level of computational complexity.

Comment
6 pages, 4 figures, accepted by 2026 IEEE/CIC International Conference on Communications in China (ICCC)

Closest papers

Nearest neighbours by meaning across the whole index.

Blind Interference Suppression for IRS-Aided Robust Wireless Communications

eess.SP ·2026-09-30 ·Tao Wang, Xiaohui Zhang, Hehe Ban, Yiwei Guo, Ming Yi
publishedbenchmark similarity 0.75
Abstract · 13 pages, 13 figures, accepted by IEEE Internet of Things Journal

The application of intelligent reflecting surfaces (IRSs) to suppress interference in wireless communication systems has recently attracted significant research attention. Most existing approaches rely on complete or partial channel state information (CSI) to configure the IRS. However, acquiring accurate CSI in IRS-assisted systems involves considerable pilot overhead and introduces non-negligible delays. This issue is further exacerbated under strong interference conditions, where interfering sources are typically non-cooperative, making CSI acquisition even more challenging. As a result, existing CSI-dependent interference suppression methods become difficult to deploy in practice. To address these limitations, we propose a novel blind interference suppression strategy that combines a proportional phase-inversion (PPI) algorithm with the conditional sample mean (CSM) method. The proposed approach determines the IRS configuration using only the received signal power, without requiring any prior CSI. We conduct a comprehensive performance evaluation by deriving the theoretical performance of the proposed scheme, which is subsequently verified through numerical simulations. Furthermore, simulation results across various parameter settings demonstrate that the proposed blind interference suppression scheme reduces the interference power to the level of noise, thereby achieving a marked signal-to-interference-plus-noise ratio (SINR) improvement and outperforms existing benchmark schemes.

0.72

Blind Interference Suppression in IRS-Aided Wireless Systems: A Statistical Channel Ratio Estimation Approach

eess.SP ·2026-09-30 ·Tao Wang, Xiaohui Zhang, Hehe Ban, Pengfei Lv, Yiwei Guo +1 more
theory similarity 0.69
Abstract · 13 pages, 6 figures, submitted to IEEE Internet of Things Journal

This paper addresses the problem of suppressing non-cooperative interference in intelligent reflecting surface (IRS)-aided wireless links without any channel state information (CSI) or cooperation from the interferer. We propose a fully blind framework that relies solely on received signal power measurements. A key insight is that nulling the aggregate interference channel requires only the complex ratios between the IRS-reflected paths and the direct interference link, rather than absolute CSI. We develop a novel estimation algorithm that obtains unbiased estimates of these channel ratios using only power samples collected under random IRS configurations. Theoretically, we prove that unbiased estimation is feasible when the number of discrete phase levels $K\geq 3$, and establish the Cramer-Rao lower bounds (CRLBs) for both the phase offset and amplitude ratio estimates, thus providing design guidance. Based on the estimated ratios, we propose two low-complexity IRS phase optimization algorithms: a one-shot greedy method and an iterative variant that mitigates error propagation from weakly reflecting elements. Simulations demonstrate that the proposed schemes can suppress strong interference to within a few dB of the interference-free upper bound, offering a practical, CSI-free solution for robust wireless communications in contested spectral environments.

0.30

RIS Configuration with Low-Overhead Measurements via Physics-Guided Neural Networks

eess.SP ·2026-10-20 ·Son Dinh-Van, Matthew D. Higgins
similarity 0.59
Abstract

This paper studies reconfigurable intelligent surface (RIS) configuration for a single-input single-output (SISO) communication link using a two-stage estimate-then-optimize procedure. Within this framework, two common approaches to the estimation stage are pilot-based channel estimation and received signal strength (RSS)-based channel estimation. Our hardware experiments reveal substantial inter-block phase evolution consistent with residual CFO, while simulations show that such phase rotations can severely degrade pilot-based channel estimation when left uncompensated. In contrast, RSS-based approaches are less affected by these phase rotations, although they often require a large number of measurements to achieve a near-optimal received signal-to-noise ratio (SNR). To address this measurement requirement, we propose parametric physics-guided neural blind beamforming (\textsc{P-PGNBB}) for RSS-based channel estimation. Simulations and hardware experiments confirm that the proposed method achieves a received SNR close to that obtained with perfect channel state information (CSI) and comparable to existing methods, while requiring substantially fewer RSS measurements.

0.20

Customizing Wireless Channels via Intelligent Reflecting Surfaces: Feasibility, Fundamental Limits, and Constructive Design

cs.IT ·2026-11-02 ·Xiyuan Liu, Qingqing Wu, Guangji Chen, Yuxuan Chen, Wen Chen
theory similarity 0.57
Abstract · 13 pages, 8 figures

By adjusting their reflection coefficients, intelligent reflecting surfaces (IRSs) can reshape the channels between a base station (BS) and user equipment (UE). Existing studies mainly optimize IRS phase-shifts for communication objectives, leaving the physical attainability of prescribed IRS-reflected channels largely unexplored. This paper investigates channel customization with a phase-only IRS under three progressively relaxed criteria. Observing that the customization mean-squared error (MSE) has the same mathematical form as the signal MSE of a point-to-point multiple-input multiple-output system, we construct a counterpart problem to characterize individual singular-coordinate gain limits and the condition for attaining the amplitude-matching upper bound. To address multi-stream phase conflicts, we analyze principal contribution area (PCA) overlap and derive sufficient array-size conditions for disjoint PCAs under a specified focused-vector construction with parallel uniform linear arrays. We also derive necessary conditions from the two propagation links' singular values and an array-size restriction under the parallel-array Fresnel model. Both the restriction and the construction involve the BS--IRS array-size product. Numerical results show that jointly selecting right singular vectors and IRS phase-shifts reduces mean customization MSE, whereas gains exceeding propagation spectral limits cannot be realized exactly. These results provide design guidance and highlight spectral limits of phase-only IRS channel customization.

0.39

When Every Bit Counts in Quantized Beamforming: From CSI Feedback to Low-Resolution Hardware

eess.SP ·2026-10-20 ·Yasaman Khorsandmanesh, Parisa Ramezani, Emil Bjornson
similarity 0.54
Abstract

Multiple-input multiple-output (MIMO) is a key technology in modern wireless networks, but its performance is often analyzed under ideal hardware assumptions. In practical implementations, however, quantization appears throughout the signal-processing chain, including channel state information (CSI) feedback, fronthaul signaling, beamforming coefficients, data converters, and finite-resolution phase shifters. These impairments do not act independently: they alter the channel information available for beamforming, constrain the feasible transmit signals, and can ultimately limit beamforming gain and interference suppression. This article provides a perspective on quantized beamforming by connecting its main sources, performance implications, and mitigation strategies. We discuss codebook-based CSI feedback, quantization-aware beamforming, low-resolution converter modeling, and finite-resolution hybrid beamforming, and use representative numerical examples to illustrate when quantization becomes a dominant performance bottleneck. We further highlight emerging directions in joint beamforming and quantization design, adaptive-resolution architectures, and new antenna technologies with discrete hardware constraints. The key message is that finite-resolution effects should be modeled explicitly and incorporated into the beamforming design rather than treated as an afterthought.

0.20

A Bussgang-based Latent Lifting Method: Discrete RIS Channel Estimation and Beamforming

eess.SP ·2026-11-07 ·Mintaek Oh, Namyoon Lee, Jinseok Choi
similarity 0.53
Abstract · 13 pages, 8 figures

This paper addresses the challenge of discrete phase-shift optimization in reconfigurable intelligent surface (RIS)-aided multiuser communication systems. Practical RIS hardware often utilizes low-resolution phase shifters, leading to challenging combinatorial optimization problems. To address this challenge, we propose a Bussgang-based latent lifting (BuLL) method that represents discrete phase shifts as quantized outputs of continuous latent variables. Our BuLL method calibrates the Bussgang gain and distortion covariance under a reference distribution and keeps these moments fixed during deterministic latent optimization. These fixed moments are then used to construct a distortion-aware continuous surrogate that incorporates reference-averaged discretization effects without penalty terms. For uplink channel estimation, we develop a matrix quadratic transform-based algorithm to optimize a mean-square-error surrogate. For downlink beamforming, we develop a generalized power iteration-based RIS phase-shift optimization algorithm for a spectral efficiency (SE) surrogate. Numerical results demonstrate improvements in channel estimation accuracy and sum SE over conventional benchmarks in the evaluated low-resolution RIS settings.

0.34

Near-Field Beamforming Design for Multi-IRS Wireless Beam Routing

eess.SP ·2026-10-07 ·Tao Wang, Changsheng You, Changchuan Yin
published similarity 0.52
Abstract · 5 pages, 3 figures, accepted by IEEE Communications Letters

This letter investigates efficient near-field beamforming designs for wireless communication systems aided by multiple extremely large-scale intelligent reflecting surfaces (Multi-XL-IRSs). Previous studies have mostly assumed far-field channel conditions, based on which angle-based beamforming is adopted for the base station (BS) and IRSs. However, this approach may lead to degraded performance in practical near-field scenarios. To address this issue, we consider near-field channel modeling and formulate an optimization problem aimed at maximizing the received power at the user equipment (UE) by jointly optimizing the beamforming at the BS and IRSs. Given the intractability under the beam training (BT)-based communication framework, the problem is revisited and reformulated. Subsequently, an efficient algorithm based on alternating optimization (AO) is proposed to solve the reformulated problem. Numerical results demonstrate that, in typical setups, our AO-based beamforming designs provide over 170% and 20% received power gains over conventional angle-based beamforming and beam focusing, respectively. Furthermore, the power scaling law derived under far-field conditions no longer holds in near-field scenarios.

0.56

Rank-Aware Element Grouping for Power-Efficient Multiuser ISAC With an Extremely Large-Scale IRS

eess.SP ·2026-08-17 ·Shengsheng Zhang, Ritao Cheng, Zitong Wang, Meng Hua, Cheng Zhang +1 more
similarity 0.52
Abstract

We investigate power-efficient multiuser integrated sensing and communication (ISAC) assisted by an element-grouping extremely large-scale intelligent reflecting surface (EG-XL-IRS). The grouping pattern is designed using slowly varying statistical channel state information (S-CSI), so that both IRS-related channel acquisition and online passive beamforming operate in the group domain rather than the element domain. We reveal a fundamental gain-rank tradeoff induced by element grouping: phase-consistent grouping can coherently enhance selected deterministic propagation components, while excessive concentration on a common deterministic mode can reduce the effective spatial rank of the multiuser channel and, for extended targets, the diversity of desired-scatterer responses. Motivated by this observation, we develop a task-adaptive rank-aware grouping strategy that balances weak-user enhancement and target-scatterer illumination while preserving task-relevant spatial dimensions. For each candidate grouping pattern, the transmit covariances and group-wise reflection phases are jointly optimized under communication and sensing quality-of-service constraints, followed by physical phase recovery and feasibility verification. Numerical results show that the proposed design substantially reduces the required transmit power compared with representative grouping benchmarks under the same grouping dimension and online optimization budget.

0.25