CS Paper Radar

RIS Configuration with Low-Overhead Measurements via Physics-Guided Neural Networks

Son Dinh-Van, Matthew D. Higgins

eess.SP ·submitted 2026-10-20 10:16 UTC · v1

Abstract

This paper studies reconfigurable intelligent surface (RIS) configuration for a single-input single-output (SISO) communication link using a two-stage estimate-then-optimize procedure. Within this framework, two common approaches to the estimation stage are pilot-based channel estimation and received signal strength (RSS)-based channel estimation. Our hardware experiments reveal substantial inter-block phase evolution consistent with residual CFO, while simulations show that such phase rotations can severely degrade pilot-based channel estimation when left uncompensated. In contrast, RSS-based approaches are less affected by these phase rotations, although they often require a large number of measurements to achieve a near-optimal received signal-to-noise ratio (SNR). To address this measurement requirement, we propose parametric physics-guided neural blind beamforming (\textsc{P-PGNBB}) for RSS-based channel estimation. Simulations and hardware experiments confirm that the proposed method achieves a received SNR close to that obtained with perfect channel state information (CSI) and comparable to existing methods, while requiring substantially fewer RSS measurements.

Closest papers

Nearest neighbours by meaning across the whole index.

TRACE: A Modular Framework for RIS-Assisted Channel Estimation and Differential Channel-Aware Reconfiguration

eess.SP eess.SY ·2026-08-12 ·Smriti Kumar, Mansi Ambwani, Arzad Alam Kherani, Vimal Bhatia
similarity 0.63
Abstract · 14 pages, 18 figures, Submitted to IEEE TCoM for review on 18th July 2026

Reconfigurable Intelligent Surface (RIS) research tightly couples channel-estimation, control and communication, yet existing implementations often rely on fixed algorithmic pipelines, making it difficult to compare alternative estimation, tracking and communication strategies under identical conditions and to study low-overhead RIS adaptation under time-varying channels. This paper addresses both challenges through two complementary contributions. First, it presents TRACE (Toolkit for RIS-assisted channel-estimation, adaptive control and communication experimentation), a modular socket-based framework that decouples the transmitter, radio environment, controller and receiver through separate control- and data-plane interfaces, enabling reproducible evaluation across substitutable modules. Second, it proposes the differential channel-aware RIS update (DCAR) algorithm, which estimates channel perturbations from reduced probe observations using a regularized differential update to reduce retraining overhead. TRACE is validated through interchangeable minimum mean square error and orthogonal matching pursuit channel-estimation, Gaussian random walk and Gauss--Markov channel evolution, BPSK, QPSK and 16-QAM modulation techniques and multiple RIS sizes, without modifying the underlying framework. Within TRACE, DCAR is observed to reduce pilot overhead and computational complexity while maintaining beamforming performance close to Kalman-filter-based tracking under time-varying channels.

0.12

Blind IRS Beamforming Using Only Received Signal Power Measurements

eess.SP ·2026-09-30 ·Tao Wang, Xiaohui Zhang, Pengfei Lv, Hehe Ban, Yiwei Guo +1 more
published similarity 0.59
Abstract · 6 pages, 4 figures, accepted by 2026 IEEE/CIC International Conference on Communications in China (ICCC)

This paper proposes a novel blind beamforming strategy for signal enhancement aided by an intelligent reflecting surface (IRS), using only samples of the received signal power. Unlike existing conditional sampling mean (CSM) based approaches, which rely solely on comparing the CSM values, the proposed algorithm fully exploits the information in the sampled data by constructing a least squares problem. This enables the estimation of the phase difference between the IRS-reflected channel and the direct channel, ultimately yielding the optimal IRS phase configuration. The simulation results verify that, by fully leveraging the collected data, the proposed scheme outperforms the CSM-based method, especially when the number of IRS phase quantization levels is larger than 2, while incurring the same level of computational complexity.

0.49

Exploiting Mutual Coupling Structure for Channel Estimation of Active RIS-Assisted Links

cs.IT eess.SP ·2026-09-17 ·Simon Tarboush, Pinjun Zheng, Hadi Sarieddeen, Tareq Y. Al-Naffouri, Giuseppe Caire
similarity 0.58
Abstract

Accurate channel modeling and estimation of active reconfigurable intelligent surface (RIS)-assisted links with densely integrated elements are essential to fully unleashing this technology's potential. This work adopts a physically consistent model incorporating mutual coupling (MC) effects, modeled via scattering parameters, in RIS-aided communication. We formulate the MC-aware channel estimation as a compressed sensing (CS) problem. The MC effect leads to an increase in the sensing matrix dimensions. This increased dimensionality substantially elevates the complexity of the formulated CS problem. To overcome this, we propose a low-complexity estimator that leverages the structure of the scattering matrix and MC mechanisms to obtain a reduced-size design sensing matrix. Numerical results demonstrate that our approach outperforms MC-unaware estimators by several dBs, achieving accuracy comparable to fully MC-aware solutions but with significantly lower complexity.

0.34

Blind Interference Suppression in IRS-Aided Wireless Systems: A Statistical Channel Ratio Estimation Approach

eess.SP ·2026-09-30 ·Tao Wang, Xiaohui Zhang, Hehe Ban, Pengfei Lv, Yiwei Guo +1 more
theory similarity 0.58
Abstract · 13 pages, 6 figures, submitted to IEEE Internet of Things Journal

This paper addresses the problem of suppressing non-cooperative interference in intelligent reflecting surface (IRS)-aided wireless links without any channel state information (CSI) or cooperation from the interferer. We propose a fully blind framework that relies solely on received signal power measurements. A key insight is that nulling the aggregate interference channel requires only the complex ratios between the IRS-reflected paths and the direct interference link, rather than absolute CSI. We develop a novel estimation algorithm that obtains unbiased estimates of these channel ratios using only power samples collected under random IRS configurations. Theoretically, we prove that unbiased estimation is feasible when the number of discrete phase levels $K\geq 3$, and establish the Cramer-Rao lower bounds (CRLBs) for both the phase offset and amplitude ratio estimates, thus providing design guidance. Based on the estimated ratios, we propose two low-complexity IRS phase optimization algorithms: a one-shot greedy method and an iterative variant that mitigates error propagation from weakly reflecting elements. Simulations demonstrate that the proposed schemes can suppress strong interference to within a few dB of the interference-free upper bound, offering a practical, CSI-free solution for robust wireless communications in contested spectral environments.

0.30

Hardware-in-the-Loop Phase-Aware CNN for Real-Time 5G Channel Estimation

eess.SP cs.CVcs.ITcs.LG ·2026-08-11 ·Javad Zolfaghari-Bengar, Rakibul Rony, Elisa Gomez-de-Lope, Alejandro Villena-Rodriguez, Abhinav Mahadevan +1 more
published similarity 0.57
Abstract · This demo paper has been accepted at IEEE CSCN 2026

This demo presents real-time AI-based uplink channel-estimation inference using data collected from a hardware-in-the-loop 5G platform. The data-collection setup integrates commercial RF signal generation, programmable channel emulation, an O-RAN Radio Unit, DU emulation, and a lightweight phase-aware convolutional neural network (CNN) that estimates the channel response directly from received DMRS signals. Unlike simulation-only evaluations, the hardware-derived dataset exposes the estimator to practical RF and system-level impairments, including calibration mismatches, synchronization imperfections, quantization effects, phase noise, and implementation-specific nonlinearities. During the demo, attendees will observe real-time CNN inference and channel reconstruction using captured hardware-generated DMRS observations and compare the proposed CNN against Least Squares (LS) and frequency-domain LMMSE baselines. The objective is to showcase a practical AI-native physical-layer inference pipeline that combines hardware-derived 5G data with real-time neural channel estimation for future 5G-Advanced and 6G systems.

0.19

A Bussgang-based Latent Lifting Method: Discrete RIS Channel Estimation and Beamforming

eess.SP ·2026-11-07 ·Mintaek Oh, Namyoon Lee, Jinseok Choi
similarity 0.57
Abstract · 13 pages, 8 figures

This paper addresses the challenge of discrete phase-shift optimization in reconfigurable intelligent surface (RIS)-aided multiuser communication systems. Practical RIS hardware often utilizes low-resolution phase shifters, leading to challenging combinatorial optimization problems. To address this challenge, we propose a Bussgang-based latent lifting (BuLL) method that represents discrete phase shifts as quantized outputs of continuous latent variables. Our BuLL method calibrates the Bussgang gain and distortion covariance under a reference distribution and keeps these moments fixed during deterministic latent optimization. These fixed moments are then used to construct a distortion-aware continuous surrogate that incorporates reference-averaged discretization effects without penalty terms. For uplink channel estimation, we develop a matrix quadratic transform-based algorithm to optimize a mean-square-error surrogate. For downlink beamforming, we develop a generalized power iteration-based RIS phase-shift optimization algorithm for a spectral efficiency (SE) surrogate. Numerical results demonstrate improvements in channel estimation accuracy and sum SE over conventional benchmarks in the evaluated low-resolution RIS settings.

0.34

Multiuser Channel Estimation in FIM Systems: A Structured Block Term Decomposition Approach

eess.SP ·2026-10-21 ·Xi Han, Junqiao Chen, André L. F. de Almeida, George C. Alexandropoulos
similarity 0.56
Abstract

Flexible intelligent metasurfaces (FIMs) create geometry-dependent array responses that provide spatial diversity but complicate multiuser channel estimation. This paper studies uplink estimation using pilot observations collected under multiple prescribed and calibrated morphing configurations. Each user contributes a matrix--vector block that couples its diagonal reference-array response with its morphing-dependent phases, while its third-mode vector is the known pilot scaled by the complex channel gain. We develop a pilot-constrained structured block term decomposition (BTD) estimator whose alternating least-squares updates exploit both the known pilot directions and the diagonal spatial factors. The undeformed configuration sets the columnwise scaling convention, and a unit first-entry normalization assigns the remaining block scale to the channel gain. Matching the recovered factors to the calibrated spatial--morphing manifold then yields the physical angles and configuration-dependent channels. We characterize the rank conditions for unique conditional least-squares updates, distinguish these conditions from global factor and physical-angle identifiability, and summarize the training, coherence-time, and computational requirements. Simulations show accurate two-dimensional angle and channel recovery in the tested settings, equal total pilot-symbol overhead in rigid-panel comparisons, improved steering-vector estimates as morphing diversity increases, and degradation as user loading or pilot correlation increases.

0.22

Structured Channel Parameter Estimation for RIS-Assisted MIMO Systems via Kronecker and Tensor Factorizations

eess.SP ·2026-09-17 ·Melryllin G. O. Sousa, Jean C. S. Ferreira, Fazal-E Asim
publishedbenchmark similarity 0.55
Abstract

This paper proposes structured channel-parameter estimators for reconfigurable intelligent surface (RIS)-assisted multiple-input multiple-output (MIMO) systems employing uniform rectangular arrays under line-of-sight propagation. By exploiting the Kronecker and multilinear structures of the cascaded channel, we introduce the Successive Kronecker Factorization (SKF) alongside two Third-Order Tensor Parameter Estimation (TOPE) methods: TOPE-ALS and TOPE-HOSVD. These estimators recover spatial signatures from the pilot-filtered signal matrix, and then decouple the corresponding horizontal and vertical spatial frequencies. This structured formulation achieves benchmark estimation accuracy while reducing computational complexity, offering a efficient solution for RIS-aided systems.

0.25