CS Paper Radar

HexaGripper: A Single-Actuator, Winch-Deployed Gripper for Autonomous Aerial Parcel Collection

Nimantha Adikaram, Mahen Abeyratne, Lakmina Chandrajith, A. H. T. E. De Silva, Isira Naotunna, Asanka Perera

cs.RO ·submitted 2026-10-05 14:31 UTC · v1

Abstract

Autonomous aerial parcel collection remains constrained by package-transfer operations that require manual loading, landing, or dedicated ground infrastructure. This letter presents HexaGripper, a single-actuator, winch-deployed six-plate gripper for autonomous collection of cuboid parcels. The proposed mechanism provides synchronized grasping with a wide capture region and tolerance to positional misalignment during pickup. The system integrates vision-based alignment, range sensing, winch deployment, and state-based control to enable autonomous collection while maintaining UAV separation from the pickup surface. Experimental evaluation covered static grasping, capture-workspace assessment, and end-to-end outdoor aerial collection. Static experiments achieved 100% pickup success (15/15 trials) across three parcel geometries, while workspace experiments achieved successful pickup at all 28 tested positions up to a 150 mm radial offset. End-to-end outdoor aerial collection achieved an 80% success rate (4/5 trials). These results demonstrate the feasibility of mechanically synchronized, winch-deployed grasping for landing-free autonomous aerial parcel collection.

Closest papers

Nearest neighbours by meaning across the whole index.

Vision-Guided Morphing Quadcopter for Multi-Geometry Payload Transport through Narrow Passages

cs.RO ·2026-08-22 ·Aashish Sahu, Shriram Hari, R. Prasanth Kumar
similarity 0.68
Abstract

Aerial payload transport using multirotor unmanned aerial vehicles is challenging because payload geometry, contact interaction, grasp stability, flight control, and narrow-passage traversal are strongly coupled during pickup and transport. Object-specific grippers often cannot adapt their footprint or grasp geometry when the payload shape or passage width changes. This paper presents a vision-guided morphing quadcopter for multi-geometry payload transport through narrow passages. The proposed platform uses four hybrid arm-leg structures that function as both landing supports and grasping members. A centrally placed actuator drives a tendon-based morphing mechanism, enabling all four arms to synchronously retract or expand for object grasping, footprint reduction, and post-transport release. Onboard vision estimates the payload geometry and passage width, while endpoint force feedback is used to confirm grasp contact during payload engagement. A phase-wise mission planner, PID-based flight stabilization, and morphology-adaptive grasp controller are implemented in a MuJoCo simulation environment. The framework is evaluated using box, cylindrical, and spherical payloads, representing flat-faced, rolling-curved, and fully curved contact conditions. Across the three cases, the simulated system completes the pickup-transport-release sequence with a maximum RMS position error of 0.31 m, a final drop-zone error below 0.18 m, a compact grasp footprint of 0.09-0.21 m2, and a footprint reduction of 75.0-89.7 percent. The results demonstrate that a single-actuator morphing quadcopter can adapt its grasp footprint for the transport of payloads with different geometries while reducing its overall footprint for narrow-passage traversal.

0.20

CAPTURER: A Dexterous Aerial Manipulator for Dynamic and Precise Grasping across Diverse Environments

cs.RO ·2026-10-29 ·Meng Wang, Jindou Jia, Sicheng Zhou, Zeshuai Chen, Kexin Guo +2 more
similarity 0.64
Abstract

As a representative form of embodied robotic interaction, aerial grasping requires close coordination between the aerial platform and manipulator. Most existing systems perform aerial grasping with static or slowly moving targets under fixed scenarios. Dynamic and precise grasping across different conditions introduces additional challenges, including target motion, localization drift, dynamic coupling, and external disturbances. In this work, we present CAPTURER, a dexterous aerial manipulator for centimeter-level grasping across diverse environments. To achieve the challenging goal, we first develop an onboard perception system for state estimation and target detection. Drift correction and global pose transformation are introduced to improve target localization during flight. A cooperative motion planner is proposed to coordinate the mobility of the aerial platform with the dexterity of the manipulator according to the relative target state. To maintain grasping accuracy under disturbances, we design a disturbance-rejection controller to compensate for dynamic coupling, model uncertainty, and external disturbances. The capability of CAPTURER is validated through indoor and outdoor experiments with both static and moving targets. The results demonstrate that CAPTURER achieves centimeter-level grasping accuracy for a marker pen measuring only 1.5 cm in diameter at flight speeds exceeding 1.5 m/s.

0.24

QuadHand: A Compact Quadrotor Aerial Manipulator with MRC-SDF-Based Whole-Body Motion Planning

cs.RO ·2026-09-28 ·Rui Jin, Ruiyang Liu, Xinhang Xu, Haotian Jin, Yi Wang +2 more
highly cited similarity 0.60
Abstract

Uncrewed aerial manipulators (UAMs) integrate robotic arms with aerial platforms for three-dimensional physical interaction. However, enlarging the workspace increases arm-induced disturbances, while existing geometric representations face a trade-off between geometric fidelity and computational efficiency in close-proximity interaction. This paper presents QuadHand, a compact quadrotor aerial manipulator with a 3-DoF arm, gripper, and battery-assisted passive CoG compensation module to reduce dominant arm-induced disturbances. We further propose MRC-SDF, a Multi-articulated Robot-Centric Signed Distance Field that preserves fine geometric detail with tractable computation, and a spatiotemporal whole-body trajectory optimization framework that jointly optimizes the quadrotor and manipulator for safe and executable trajectory generation. Simulations and real-world experiments demonstrate safe and executable aerial manipulation in complex environments.

0.35

Aerial Layouting: Design and Control of a Compliant and Actuated End-Effector for Precise In-flight Marking on Ceilings

cs.RO ·2026-08-11 ·Christian Lanegger, Marco Ruggia, Marco Tognon, Lionel Ott, Roland Siegwart
publishedhighly cited similarity 0.60
Abstract · C. Lanegger and M. Ruggia contributed equally. Accepted to Robotics: Science and Systems (RSS) 2022

Aerial robots have demonstrated impressive feats of precise control, such as dynamic flight through openings or highly complex choreographies. Despite the accuracy needed for these tasks, there are problems that require levels of precision that are challenging to achieve today. One such problem is aerial interaction. Advances in aerial robot design and control have made such contact-based tasks possible and opened up research into challenging real-world tasks, including contact-based inspection. However, while centimetre accuracy is sufficient and achievable for inspection tasks, the positioning accuracy needed for other problems, such as layouting on construction sites or general push-and-slide tasks, is millimetres. To achieve such a high precision, we propose a new aerial system composed of an aerial vehicle equipped with a novel "smart" end-effector leveraging a stability-optimized Gough-Stewart mechanism. We present its design process and features incorporating the principles of compliance, multiple contact points, actuation, and self-containment. In experiments, we verify that the design choices made for our novel end-effector are necessary to obtain the desired positioning precision. Furthermore, we demonstrate that we can reliably mark lines on ceilings with millimetre accuracy without the need for precise modeling or sophisticated control of the aerial robot.

0.61

Robust Sliding Mode and Admittance Control of Underactuated Aerial Manipulators for Contact-Based Inspection

cs.RO ·2026-08-11 ·Tareq Aziz Alqutami, Yvan Petillot, Matthew W. Dunnigan, Mustafa Suphi Erden
published similarity 0.60
Abstract · 6 pages, 7 figures, submitted to 2026 IEEE Industrial Electronics and Applications Conference (IEACon)

Contact-based industrial inspection requires aerial platforms to maintain stable interaction while rejecting disturbances. Underactuated aerial manipulators present control challenges due to the dynamic coupling between vehicle attitude and force generation. This paper proposes a robust control framework for an underactuated hexarotor equipped with a 1-DoF manipulator to perform sustained contact inspection. The architecture integrates integral-augmented Sliding Mode Control (SMC) for trajectory tracking with an admittance control law for force regulation. The contact force is mapped to a feedforward attitude term, while the 1-DoF arm actively compensates for the tilt to maintain surface alignment. Software-in-the-loop simulations demonstrate that the SMC-based approach achieves superior tracking and coupling rejection compared to traditional PID. Furthermore, the interaction strategy achieved precise force regulation with an RMSE of 0.12N and was able to stably exert up to 20N force, confirming the system's efficacy for stable, reliable contact-based inspection.

0.26

Hybrid Roller-Jamming Gripper for Object Acquisition and Retention Under Pose Uncertainty

cs.RO ·2026-08-21 ·Yijie Ren, Guillaume Gourmelen, Hiroyasu Iwata
published similarity 0.59
Abstract · 11 pages, 16 figures, under review

In household manipulation, pose uncertainty often results in off-centre or partial initial contact, making reliable object acquisition difficult. Roller-based grippers can actively draw objects inward but often provide limited post-capture stability, whereas granular-jamming grippers require sufficient contact before jamming to achieve strong retention. This paper presents a hybrid roller-jamming gripper that integrates active object intake and post-capture retention within a single gripper. The proposed gripper uses inward roller rotation to increase contact and draw the object toward the gripper centre, followed by vacuum-induced granular jamming to stiffen the rollers and stabilise the grasp. The paper also presents a simplified geometric analysis of the gripper and a bench-level characterisation of the prototype's force capability. The gripper prototype was mounted on a 7-DoF robotic arm and evaluated using eight test objects. Furthermore, controlled planar position and orientation offsets were applied, with each condition repeated three times. The main evaluation comprised 840 grasp trials, including 216 planar-offset trials and 624 orientation-offset trials. Overall, the gripper succeeded in 812/840 trials: 215/216 planar-offset trials and 597/624 orientation-offset trials. The ablation evaluation comprised 162 trials on three objects. The roller-only and jamming-only conditions achieved 54/81 and 24/81 successes, respectively, showing their different contributions. These results provide initial mechanism-level evidence that hybrid roller-jamming is a promising strategy for improving acquisition and retention after imperfect first contact.

0.41

Cooperative Aerial Transportation of a Payload with a Sliding Cable Attachment

cs.RO cs.MA ·2026-10-09 ·Sebastian Tilaguy Lezama, Diego S D'Antonio
similarity 0.59
Abstract

This paper presents a dual-quadrotor hook- suspended transport system for cooperative aerial manipulation of a payload that is not rigidly attached to a fixed point along the cable. Two quadrotors are connected by a single inextensible cable that passes through a frictionless hook mounted on the payload, allowing the cable to slide between its two segments. This introduces a cable-distribution variable that couples the quadrotor motion, cable geometry, and payload dynamics. A feasible reference-generation framework is formulated using the desired payload pose, cable distribution, and system shape while satisfying the cable-length constraint and elliptical workspace. The quadrotors track the geometrically generated trajectories while maintaining positive cable tension and respecting actuator limits. The payload pose is estimated from the system geometry, and its measured position is used only to validate the desired trajectory. The approach is evaluated through experimental demonstrations.

0.33

Gripper-Aware Automatic Dense Packing of Irregular Objects

cs.RO ·2026-09-18 ·Tianhao Qin, Connor McCann, Berk Calli, Jing Xiao
publishedbenchmark similarity 0.58
Abstract · Accepted at ISRR 2026

Automatic dense packing is widely desired in warehouse operations but remains a fundamental challenge in robotic manipulation. Existing work on irregular-object packing largely targets simulation with idealized contact, treating the object as an isolated rigid body. The gripper often enters as a discrete, post-hoc feasibility check, if considered at all, and the perception and contact drift accumulated during execution are not addressed. We present a closed-loop pipeline that integrates perception, gripper-aware placement optimization, and force-guided execution on a real manipulator. The optimizer represents the object together with the gripper as a single composite body of hierarchical sphere trees. It searches over five degrees of freedom on a GPU within a CMA-ES framework, with the vertical coordinate grounded analytically against the current heightmap. During execution, a force-monitored vertical descent stops on first contact. A post-release consolidation push then closes the residual lateral clearance that gripper-aware planning leaves behind. The container is re-perceived between placements so that drift does not accumulate. We validate the system on a Franka Emika Panda robot packing a 3D-printed set of flat, curved, and concave objects, and a YCB object subset. An ablation study isolates the contribution of gripper-aware optimization, the consolidation push, and mesh-derived geometry to end-to-end success, achieved density, and computational cost. We further benchmark against the heightmap-minimization method as a baseline representative of prior irregular-object packing work.

0.31