CS Paper Radar

Time-Domain Analysis of Surface Acoustic Wave Magnetoelectric Sensors

Mohsen Samadi, Henrik Wolframm, Felix Weisheit, Dirk Meyners, Eckhard Quandt, Michael Höft, Martina Gerken

eess.SY physics.app-phcond-mat.mtrl-sci ·submitted 2026-10-08 07:48 UTC · v1
unusual

Abstract

The transient response of surface acoustic wave sensors is important for understanding their dynamic behavior, propagation delay, and response to time-varying signals. In this work, the time-domain propagation characteristics of a magnetoelectric SAW sensor based on a multilayer Love-wave delay line are investigated using complementary numerical and experimental approaches. Time-domain analysis is employed to determine the delay time and to extract the phase and group velocities, while frequency-domain analysis provides an independent characterization of the wave dispersion. Both numerically and experimentally, the phase and group velocities are found to differ, reflecting the dispersion of the Love wave in the multilayer structure. At the operating frequency of 146 MHz, the simulated group velocity obtained from wave-field tracking agrees within 0.4% with the value determined from the frequency-domain dispersion relation. The simulated delay time and group velocity also show good agreement with experiment, with deviations of 2.7% in delay time and 0.9% in group velocity. These results demonstrate the consistency of the time- and frequency-domain analyses and provide a quantitative characterization of the transient propagation behavior of SAW sensors.

Comment
18 pages, 6 figures, 1 table

Closest papers

Nearest neighbours by meaning across the whole index.

Toward Ku-Band Surface Acoustic Wave Delay Lines on AlScN-on-Diamond with Decoupled Phase and Group Velocities

eess.SP ·2026-09-15 ·Tzu-Hsuan Hsu, Kapil Saha, Yuchen Ma, Vakhtang Chulukhadze, Pietro Simeoni +2 more
unusual similarity 0.47
Abstract · 4 pages, 8 figures, submitted to IEEE IUS 2026 conference

This work reports surface acoustic wave (SAW) acoustic delay lines (ADLs) on an aluminum scandium nitride (AlScN) on diamond platform operating in the X band and approaching the Ku band. The large acoustic-velocity contrast between the AlScN film and the diamond substrate produces a strongly dispersive Sezawa branch that decouples the phase velocity from the group velocity. Delay lines with a 1 $μ$m wavelength show a Sezawa passband at 9.55 GHz with a fractional bandwidth of 1.05%, a propagation loss of 0.094 dB per wavelength, a propagation-limited quality factor of 465, and a group velocity of 5979 m/s, while co-fabricated resonators give a phase velocity of 9560 m/s, a ratio of about 1.6. Scaling the wavelength to 0.5 $μ$m moves the passband to 16.5 GHz with a fractional bandwidth of 0.7%. The platform therefore reaches an operating frequency about 1.5 times higher than AlScN on sapphire at the same lithographic pitch while preserving group delay per unit length.

0.27

Evaluation of effective wave velocities in polycrystalline materials using the ultrasonic reflection matrix

eess.IV physics.app-ph ·2026-09-22 ·Gatien Clément, Alexandre Aubry, Cécile Brütt, Benoît Gérardin, Claire Prada
unusual similarity 0.42
Abstract · 13 pages, 14 figures

In-depth characterization of heterogeneous materials has long been a challenge in non-destructive testing. Here, a method is proposed to determine the elastic constants of metallic polycrystalline materials using back-scattered ultrasound. The waves scattered by the microstructure are analyzed to image the effective bulk velocities. To this end, a reflection matrix is acquired with an array of transducers. The projection of this matrix onto a focused basis is used to estimate an average point spread function. Optimizing this function with respect to the propagation model leads to an estimation of the longitudinal velocity. Additional treatments are developed to adapt the method to map the shear wave velocity. The local Poisson's ratio is then deduced from the ratio between those two velocities. Young's modulus and shear modulus can also be obtained assuming known densities. This matrix approach is experimentally validated on different polycrystalline materials. A sample displaying heterogeneous mechanical properties is then simulated to assess the accuracy and the resolution of the method. Its strengths and limitations are discussed, demonstrating its potential for quantitative non-destructive material characterization.

0.30

20 ghz longitudinal surface acoustic wave resonators in 100-nm x-cut lithium niobate on silicon carbide

eess.SP ·2026-11-19 ·Jiajun Huang, Ziqian Yao, Tzu-Hsuan Hsu, Ian Anderson, Joshua Campbell +1 more
similarity 0.42
Abstract

Surface acoustic wave (SAW) resonators above 15~GHz require a fast acoustic mode that retains strong electromechanical coupling ($k^2$). This work reports longitudinal SAW (L-SAW) resonators designed for high $k^2$ in 100-nm X-cut lithium niobate (LN) on 4H silicon carbide (SiC), operating up to 21.7~GHz and reaching a $k^2$ of 8.1\%, a maximum Bode $Q$ of 70, and a figure of merit (FoM) of 5.7 at 20.24~GHz. In this thin-film waveguide, shrinking the wavelength ($λ$) keeps the normalized LN thickness ($h_\mathrm{LN}/λ$) large, sustaining both $k^2$ and acoustic confinement. Conversely, increasing $λ$ from 292 to 471~nm lowers $h_\mathrm{LN}/λ$ from 0.34 to 0.21 and raises the L-SAW phase velocity from 6.32 to 7.05~km/s, within 1.1\% of the 7126-m/s shear-wave velocity of 4H-SiC. As the velocity approaches this limit, more of the acoustic energy spreads into the non-piezoelectric SiC, and $k^2$ falls from its 8.1\% peak at $λ= 322$~nm to 1.7\% at $λ= 471$~nm. No L-SAW resonance is observed for $λ\geq 518$~nm ($h_\mathrm{LN}/λ\leq 0.19$), where the mode becomes leaky. Overall, the FoM stays within 5\% of its maximum for $h_\mathrm{LN}/λ$ between 0.26 to 0.31, defining a design window for L-SAW resonators in thin LN on SiC at K-band and beyond.

0.27

Identifying the Shear Piezoelectric Coefficient using Physics-Informed Neural Networks under Exact Boundary and Initial Constraints

cs.LG physics.comp-phcond-mat.mtrl-sciphysics.app-ph ·2026-11-02 ·Suhas Suresh Bharadwaj
similarity 0.40
Abstract · 19 pages, 9 figures

The shear piezoelectric coefficient $e_{15}$ governs the shear-mode electromechanical coupling in piezoelectric micromachined ultrasonic transducers (PMUTs) and surface acoustic wave (SAW) devices, but measuring it typically requires destructive resonance testing on dedicated specimens. On simulated data, $e_{15}$ can instead be recovered non-destructively from sparse, noisy subsurface wavefield observations using a constrained physics-informed neural network (PINN). By building exact spatial distance functions and temporal multipliers directly into the network output, the clamped, grounded boundaries and resting initial state hold automatically, leaving the loss with only the interior equations of coupled electro-elastodynamics and the data misfit. Non-dimensional scaling brings all governing coefficients within one decade of O(1), and the setup removes the boundary and initial-condition penalty weights that soft-constraint methods must tune. In a six-way comparison (plane-strain PZT-5H, manufactured wavefield, 30 dB noise), a soft-penalty baseline with adaptive weights converges to an erroneous $e_{15}$ in four of the five runs (51.7% mean error), and fixed penalties reach an error of 0.85% only after a second-order optimization stage. The constrained formulations reach mean $e_{15}$ errors between 0.15% and 0.51% with held-out displacement errors below 1%. Within these variants, the spatial multiplier gives rapid first-order convergence, and the quadratic temporal multiplier lowers the early-time electrostatic residual by a factor of 6.8 versus a linear one. On finite-element data along one subsurface line, the full formulation recovers $e_{15}$ with 1.19% mean error at 30 dB and keeps it between 0.65% and 2.71% across a 40 to 0 dB noise sweep. Finally, training on displacements alone still recovers $e_{15}$ with mean errors of 0.45% on finite-element and 1.64% on manufactured data.

0.27

Arctic Dispersion Interruption Phenomenon and Sound Source Depth Estimation

cs.SD physics.app-ph ·2026-08-31 ·Weng Jinbao, Yang Yanming, Chen Benqing, Xu Dewei, Zhou Hongtao
unusual similarity 0.39
Abstract

The sound speed profile in the deep Arctic Ocean causes the surface layer to form a normal mode waveguide. When the depth of the sound source or receiver is near a node of the eigenfunction, the source cannot excite the mode, or the receiver cannot detect it, resulting in the modal amplitude at the receiver being approximately zero. This manifests as a dispersion interruption in the dispersion structure, which can be observed through time-frequency analysis of the received acoustic signal. Based on the interruption frequency identified from the received signal, combined with the relationship between node depth and modal frequency calculated from the ocean sound speed profile, the source depth can be estimated if the receiver depth is known. The phenomenon of dispersion interruption and the method of estimating source depth have been validated through simulations and experiments.

0.25

Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

eess.SP ·2026-11-09 ·Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu +6 more
similarity 0.39
Abstract · 8 pages, 11 figures

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm$^{2}$, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency ($k_{\mathrm{eff}}^{2}$) of 3% and a moderate static capacitance $C_0$ of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement ($ξ_{\mathrm{static}}$) of 145 nm/V and a high corresponding open-circuit sensitivity ($S_{\mathrm{OC}}$) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

0.33

A robust single-sensing-element tactile sensor for concurrent pressure and tackiness detection with real-time signal decoupling capability

cs.RO cond-mat.mtrl-sci ·2026-09-29 ·Ying Yang, Mingwei Gu, Jia-Sen Xie, Xingyu Ma, Yan-Na Lu +6 more
similarity 0.37
Abstract

Integrating tackiness sensation into the artificial skin of humanoid robots significantly enhances their cognitive and operational capabilities. However existing tactile sensors face challenges in decoupling of the multimodal signal and stability. Here we present a surface-soft tactile sensor that incorporates a Hall effect sensor and a soft magnetic composite within a robust elastic framework. The sensor surface indents under pressure and bulges prominently when retracted from sticky surfaces dynamically altering the Hall sensor-magnet distance. This generates whole-process-traceable and baseline-separated signals enabling real-time differentiation between pressure and pull-off force. This single-sensing-element design facilitates bimodal sensing at the same contact spot while eliminate stress cross-talk enhancing both accuracy and sensitivity. The fusion of a robust framework and magneto-mechanical sensing mechanism equips the sensor with exceptional reliability and excellent signal baseline stability. This tactile sensor holds substantial potential for advancing robotic capabilities in evaluating adhesive properties monitoring rubber aging precisely handling lightweight objects and cognizing natural objects surface characteristics.

0.20

Gradient-Field Frequency Encoding for 1D Localization of Magneto-Mechanical Resonators

eess.SP eess.SY ·2026-10-05 ·Fabian Mohn, Martin Möddel, Tobias Knopp
similarity 0.36
Abstract · 4 pages, 3 figures

Magneto-mechanical resonators (MMRs) have emerged as promising passive sensors for wireless localization and remote inductive sensing in industrial and medical environments. However, fundamental limits on achievable localization accuracy using the spatial sensitivity profiles of receive coils remain a key challenge. In this work, we demonstrate that an MMR - comprising two permanent magnets in an anti-parallel arrangement - exhibits a measurable shift in its mechanical resonance frequency in response to an externally applied magnetic field, a property we exploit for spatial encoding. We derive and experimentally validate a method that maps frequency shifts of 1D positions within a known magnetic gradient field, demonstrating accurate localization along a linear trajectory. This gradient-field frequency encoding approach constitutes a conceptually distinct alternative to conventional sensitivity encoding with receiver coil arrays, with the potential to simplify hardware requirements while improving localization accuracy.

0.27