CS Paper Radar

Toward Ku-Band Surface Acoustic Wave Delay Lines on AlScN-on-Diamond with Decoupled Phase and Group Velocities

Tzu-Hsuan Hsu, Kapil Saha, Yuchen Ma, Vakhtang Chulukhadze, Pietro Simeoni, Matteo Rinaldi, Ruochen Lu

eess.SP ·submitted 2026-09-15 17:00 UTC · v1
unusual

Abstract

This work reports surface acoustic wave (SAW) acoustic delay lines (ADLs) on an aluminum scandium nitride (AlScN) on diamond platform operating in the X band and approaching the Ku band. The large acoustic-velocity contrast between the AlScN film and the diamond substrate produces a strongly dispersive Sezawa branch that decouples the phase velocity from the group velocity. Delay lines with a 1 $μ$m wavelength show a Sezawa passband at 9.55 GHz with a fractional bandwidth of 1.05%, a propagation loss of 0.094 dB per wavelength, a propagation-limited quality factor of 465, and a group velocity of 5979 m/s, while co-fabricated resonators give a phase velocity of 9560 m/s, a ratio of about 1.6. Scaling the wavelength to 0.5 $μ$m moves the passband to 16.5 GHz with a fractional bandwidth of 0.7%. The platform therefore reaches an operating frequency about 1.5 times higher than AlScN on sapphire at the same lithographic pitch while preserving group delay per unit length.

Comment
4 pages, 8 figures, submitted to IEEE IUS 2026 conference

Closest papers

Nearest neighbours by meaning across the whole index.

20 ghz longitudinal surface acoustic wave resonators in 100-nm x-cut lithium niobate on silicon carbide

eess.SP ·2026-11-19 ·Jiajun Huang, Ziqian Yao, Tzu-Hsuan Hsu, Ian Anderson, Joshua Campbell +1 more
similarity 0.59
Abstract

Surface acoustic wave (SAW) resonators above 15~GHz require a fast acoustic mode that retains strong electromechanical coupling ($k^2$). This work reports longitudinal SAW (L-SAW) resonators designed for high $k^2$ in 100-nm X-cut lithium niobate (LN) on 4H silicon carbide (SiC), operating up to 21.7~GHz and reaching a $k^2$ of 8.1\%, a maximum Bode $Q$ of 70, and a figure of merit (FoM) of 5.7 at 20.24~GHz. In this thin-film waveguide, shrinking the wavelength ($λ$) keeps the normalized LN thickness ($h_\mathrm{LN}/λ$) large, sustaining both $k^2$ and acoustic confinement. Conversely, increasing $λ$ from 292 to 471~nm lowers $h_\mathrm{LN}/λ$ from 0.34 to 0.21 and raises the L-SAW phase velocity from 6.32 to 7.05~km/s, within 1.1\% of the 7126-m/s shear-wave velocity of 4H-SiC. As the velocity approaches this limit, more of the acoustic energy spreads into the non-piezoelectric SiC, and $k^2$ falls from its 8.1\% peak at $λ= 322$~nm to 1.7\% at $λ= 471$~nm. No L-SAW resonance is observed for $λ\geq 518$~nm ($h_\mathrm{LN}/λ\leq 0.19$), where the mode becomes leaky. Overall, the FoM stays within 5\% of its maximum for $h_\mathrm{LN}/λ$ between 0.26 to 0.31, defining a design window for L-SAW resonators in thin LN on SiC at K-band and beyond.

0.27

Time-Domain Analysis of Surface Acoustic Wave Magnetoelectric Sensors

eess.SY physics.app-phcond-mat.mtrl-sci ·2026-10-08 ·Mohsen Samadi, Henrik Wolframm, Felix Weisheit, Dirk Meyners, Eckhard Quandt +2 more
unusual similarity 0.47
Abstract · 18 pages, 6 figures, 1 table

The transient response of surface acoustic wave sensors is important for understanding their dynamic behavior, propagation delay, and response to time-varying signals. In this work, the time-domain propagation characteristics of a magnetoelectric SAW sensor based on a multilayer Love-wave delay line are investigated using complementary numerical and experimental approaches. Time-domain analysis is employed to determine the delay time and to extract the phase and group velocities, while frequency-domain analysis provides an independent characterization of the wave dispersion. Both numerically and experimentally, the phase and group velocities are found to differ, reflecting the dispersion of the Love wave in the multilayer structure. At the operating frequency of 146 MHz, the simulated group velocity obtained from wave-field tracking agrees within 0.4% with the value determined from the frequency-domain dispersion relation. The simulated delay time and group velocity also show good agreement with experiment, with deviations of 2.7% in delay time and 0.9% in group velocity. These results demonstrate the consistency of the time- and frequency-domain analyses and provide a quantitative characterization of the transient propagation behavior of SAW sensors.

0.29

13,000-Fold Frequency Down Conversion From 280 MHz to 21 kHz Using Mechanical Frequency Combs

eess.SP ·2026-11-05 ·Ian Anderson, Zihuan Liu, Vivek Tallavajhula, Yen-Chen Wang, Tzu-Hsuan Hsu +2 more
unusual similarity 0.41
Abstract · 4 pages, 6 figures

Optical frequency combs bridge the microwave and terahertz regimes by down-converting terahertz optical energy into microwave signals. A photodetector converts the comb's equally spaced lines, generated through optical nonlinearities, into a low-frequency tone at their spacing. Here, we present the first mechanical version of this process, using mechanical frequency combs to downconvert energy over 4 orders of magnitude, from the MHz to kHz regime. Thin-film lithium niobate (LN) is used to design an acoustic resonator with a wide range of mode frequencies. We achieve phononic comb excitation from 250 MHz to 900 MHz and compare the electrical and laser Doppler vibrometer (LDV) measurements at 277 MHz. We then show the low-frequency spectrum of the devices, highlighting mechanical motion at the comb's spacing and demonstrating energy transfer from 277 MHz to 21 kHz.

0.30

Edge-Combining Subharmonic Mixer-First Receiver

eess.SP ·2026-11-17 ·Eric Danson, Jeffrey S. Walling
unusual similarity 0.40
Abstract · 4 pages, 10 figures, 1 Table

A 1-10 GHz subharmonic mixer-first receiver using edge combining to drive N-path switches from 50% duty-cycle clocks at half the local oscillator (LO) frequency avoids the gain penalty of harmonic mixing. Inverter-based differential baseband amplifiers with back-gate feedback linearization set their gain by process-defined capacitance ratios, using no additional components and consuming no additional power. A 22 nm fully depleted silicon on insulator (FD-SOI) prototype receiver achieves a conversion gain of 12.8-18.1 dB and a noise figure of 5.7-11 dB across the band. It achieves up to 15.4 dBm out-of-band IIP3 while consuming 16.7-22.3 mW.

0.31

Contact-Limited Throughput of a Buoyless Acoustic-to-LEO Gateway With Anticipatory Preparation

eess.SP ·2026-09-14 ·Muhammad Khalil
unusual similarity 0.39
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

A buoyless acoustic-to-LEO gateway with predictable contacts is analyzed. Advanceable cross-medium preparation competes with acoustic collection, while residual RF acquisition consumes contact time. Exact fluid and packet service, a fluid-optimal fixed preparation lead, tandem-queue stability, and one-contact reliability are derived. An explicit service-bias identity shows why treating acquisition as advanceable can select an insufficient lead. For lognormal preparation, conditions are characterized under which variability improves mean service while degrading reliability. Monte Carlo and packet-queue simulations corroborate the analysis with synthetic parameters; in a diagnostic case, accounting for residual RF acquisition raises the actual sustainable rate from 8.776 to 9.079 kbit/s.

0.25

Split-Ring Couplers for On-Skin Wi-Fi Communication via an SSPP Waveguide Textile

eess.SP physics.app-ph ·2026-11-09 ·Akihito Noda, Ryo Takahashi
similarity 0.38
Abstract · 4 pages, 6 figures

Textile spoof surface plasmon polariton (SSPP) waveguides offer guided on-body links, but their body-facing ground conductors obstruct coupling from on-skin wireless nodes. This letter presents a split-ring coupling interface using local ground recesses at the textile terminations, without patterned garment-side launchers. The capacitively loaded rings are supported by polydimethylsiloxane carriers with a thickness of 2~mm. An image-current model and full-wave simulations examine the effect of backing-ground spacing and determine the recess geometry. For a 450~mm textile waveguide on a water-filled body phantom, the measured $S_{21}$ at 2.45 GHz was $-$18.8~dB, versus $-$60.9~dB without the textile. A 625-position scan showed a maximum 5.1 dB reduction relative to the nominal position within the measured joint $\pm$5~mm placement region. A separate two-node IEEE~802.11n test demonstrated a 65~Mb/s physical-layer (PHY) rate with zero packet errors among 300 frames at $-$20~dBm transmit power through the coupler link. These results establish high-rate, placement-tolerant on-skin Wi-Fi communication through an SSPP waveguide textile.

0.26

Packet-Level Complex CIR Tracking for Communication-Native mmWave Sensing: An 802.11ad Testbed

eess.SP ·2026-09-14 ·Raquel Marina Noguera Oishi, Haoqiu Xiong, Hany Assasa, Sofie Pollin
similarity 0.38
Abstract

Commercial millimetre-wave (mmWave) Wi-Fi platforms based on IEEE 802.11ad/ay have demonstrated sensing capabilities, but they provide limited visibility into the packet-level measurements and synchronisation mechanisms that determine temporal coherence. We present a programmable 60~GHz IEEE 802.11ad testbed that exposes the complete complex 128-tap channel impulse response (CIR) for every detected packet. This access exposes packet-to-packet delay shifts and common phase drift that commercial-transceiver studies generally do not characterise. We develop a delay-profile alignment method and define a static-reference relative CIR phase that cancels common drift while preserving target-induced variation. We use 30~s respiration sensing to evaluate long-term phase stability for sub-wavelength motion tracking. Across 39 recordings, median absolute waveform correlation increases from 0.41 (timestamp regularised) to 0.52 (delay aligned) and 0.61 (relative-phase calibrated); breathing-rate mean absolute error decreases from 5.1 to 4.1 and 3.6~breaths/min. The results demonstrate controlled characterisation and stabilisation of communication-native WiGig CIR measurements on a fully programmable physical layer.

0.26

Low-Data OOD Prediction of SAW Resonators with Simulation-Compensated Transfer Learning

eess.SY ·2026-11-11 ·Zhijie Ma, Xingyu Liu, Shuhan Chen, Fangsheng Qian, Junyan Zheng +4 more
published similarity 0.38
Abstract

Surface acoustic wave (SAW) resonators are foundational to modern radio-frequency (RF) front-end architectures. However, models trained on limited fabricated devices generalize poorly to unmeasured design regions because of process-induced variations, while finite-element method (FEM) simulations, although inexpensive, exhibit systematic offsets from measurements. To predict device performance before physical prototyping, this work presents a simulation-compensated transfer-learning framework that uses computationally efficient 2.5-D FEM simulations as physics-based anchors and learns their calibration to the measurement domain. Using 4,236 measured lithium tantalate (LiTaO3) SAW resonators and 816 unique simulated configurations, five transfer strategies are systematically benchmarked under seven out-of-distribution (OOD) protocols spanning frequency, geometry, and material shifts. The proposed framework reduces OOD prediction error by 83.54% on average (up to 97.57%) relative to the Measurement-only baseline, with the best strategy selected per case, and raises the pooled R2 of frequency prediction to 1.000, offering an economically scalable route toward physics-guided, fabrication-aware machine learning for microelectromechanical-system (MEMS) acoustic-device design.

0.32