CS Paper Radar

13,000-Fold Frequency Down Conversion From 280 MHz to 21 kHz Using Mechanical Frequency Combs

Ian Anderson, Zihuan Liu, Vivek Tallavajhula, Yen-Chen Wang, Tzu-Hsuan Hsu, Neal Hall, Ruochen Lu

eess.SP ·submitted 2026-11-05 22:16 UTC · v1
unusual

Abstract

Optical frequency combs bridge the microwave and terahertz regimes by down-converting terahertz optical energy into microwave signals. A photodetector converts the comb's equally spaced lines, generated through optical nonlinearities, into a low-frequency tone at their spacing. Here, we present the first mechanical version of this process, using mechanical frequency combs to downconvert energy over 4 orders of magnitude, from the MHz to kHz regime. Thin-film lithium niobate (LN) is used to design an acoustic resonator with a wide range of mode frequencies. We achieve phononic comb excitation from 250 MHz to 900 MHz and compare the electrical and laser Doppler vibrometer (LDV) measurements at 277 MHz. We then show the low-frequency spectrum of the devices, highlighting mechanical motion at the comb's spacing and demonstrating energy transfer from 277 MHz to 21 kHz.

Comment
4 pages, 6 figures

Closest papers

Nearest neighbours by meaning across the whole index.

20 ghz longitudinal surface acoustic wave resonators in 100-nm x-cut lithium niobate on silicon carbide

eess.SP ·2026-11-19 ·Jiajun Huang, Ziqian Yao, Tzu-Hsuan Hsu, Ian Anderson, Joshua Campbell +1 more
similarity 0.55
Abstract

Surface acoustic wave (SAW) resonators above 15~GHz require a fast acoustic mode that retains strong electromechanical coupling ($k^2$). This work reports longitudinal SAW (L-SAW) resonators designed for high $k^2$ in 100-nm X-cut lithium niobate (LN) on 4H silicon carbide (SiC), operating up to 21.7~GHz and reaching a $k^2$ of 8.1\%, a maximum Bode $Q$ of 70, and a figure of merit (FoM) of 5.7 at 20.24~GHz. In this thin-film waveguide, shrinking the wavelength ($λ$) keeps the normalized LN thickness ($h_\mathrm{LN}/λ$) large, sustaining both $k^2$ and acoustic confinement. Conversely, increasing $λ$ from 292 to 471~nm lowers $h_\mathrm{LN}/λ$ from 0.34 to 0.21 and raises the L-SAW phase velocity from 6.32 to 7.05~km/s, within 1.1\% of the 7126-m/s shear-wave velocity of 4H-SiC. As the velocity approaches this limit, more of the acoustic energy spreads into the non-piezoelectric SiC, and $k^2$ falls from its 8.1\% peak at $λ= 322$~nm to 1.7\% at $λ= 471$~nm. No L-SAW resonance is observed for $λ\geq 518$~nm ($h_\mathrm{LN}/λ\leq 0.19$), where the mode becomes leaky. Overall, the FoM stays within 5\% of its maximum for $h_\mathrm{LN}/λ$ between 0.26 to 0.31, defining a design window for L-SAW resonators in thin LN on SiC at K-band and beyond.

0.26

Lithium Niobate Surface-Acoustic-Wave Resonator for Very-High-Frequency Isolated Power Conversion

eess.SY physics.app-ph ·2026-10-02 ·Liyang Jin, Zhiyang Cao, Zichen Xi, Jun Ji, Yizheng Zhu +2 more
unusual similarity 0.53
Abstract

Piezoelectric devices offer a promising magnetic-free alternative for high-frequency power electronics, enabling compact energy transfer with inherent galvanic isolation. Here we demonstrate a lithium niobate surface acoustic wave (SAW) resonator that enables isolated power transfer and addresses the challenges in existing piezoelectric devices for power applications, including operation frequencies, power delivery figure of merit (FOM), power handling, and electrical isolation. Our application-optimized 40-MHz SAW resonator, with the two electrically isolated interdigital transducers (IDTs) and acoustic Bragg mirrors, achieves a 25.7 W output power at a less than 15 °C temperature rise with only passive cooling through the back mounting side, and an isolation voltage of 2.17 kV. In DC-AC power conversion, we demonstrate a peak efficiency of 93.8 %, a power delivery FOM of 13.47 mW/V$^2$ and a peak chip power density of 81.7 W/cm$^3$. DC-DC conversion is also demonstrated by connecting a diode rectifier to the output IDT, despite efficiency degrading to 52.7 %. Our results advance SAW devices as one of the core components for next-generation very-high-frequency, miniaturized, high-density, magnetic-free, isolated power converters.

0.26

Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

eess.SP ·2026-11-09 ·Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu +6 more
similarity 0.52
Abstract · 8 pages, 11 figures

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm$^{2}$, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency ($k_{\mathrm{eff}}^{2}$) of 3% and a moderate static capacitance $C_0$ of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement ($ξ_{\mathrm{static}}$) of 145 nm/V and a high corresponding open-circuit sensitivity ($S_{\mathrm{OC}}$) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

0.33

High-Velocity Whip-Mode Microresonator in LTOI Unimorph: Measurement Methodology and Large-Signal Characterization

eess.SP ·2026-09-16 ·Tzu-Hsuan Hsu, Zihuan Liu, Harshvardhan Gupta, Ziqian Yao, Wei Wang +4 more
theoryunusual similarity 0.50
Abstract · 10 pages, 9 figures, 2 tables. Submitted to IEEE Journal of Microelectromechanical Systems

This paper presents the design, characterization, and large-signal measurement methodology of a high-order whip-mode flexural microresonator on a lithium tantalate-on-insulator (LTOI) unimorph platform. A tapered cantilever concentrates kinetic energy at the free tip through a structural velocity amplification effect, with a targeted whip mode at 9.175 MHz exhibiting a measured Q of 691 in air. The results indicate a substantially reduced susceptibility to viscous damping at high modal frequencies. In-air large-signal testing on a separate device confirms tip velocities up to 20 m/s before the reliable measurement range of the laser Doppler vibrometer (LDV) at the tapered tip is exceeded, while the device itself sustains drive levels up to 240 Vpp before failure. Transitioning to vacuum reveals photothermal-induced static bending of the LTOI cantilever under LDV laser illumination, an effect that prohibits direct velocity measurement for these resonators. Hence, it motivates an indirect extraction methodology to be implemented. In this work, a 3.85 times base-to-tip geometric amplification factor, independently calibrated at low drive, is applied to base velocity measurements to infer tip velocity under large-signal conditions. Using this approach with narrowband chirp excitation, a maximum extracted tip velocity of 58.9 m/s is obtained at 192 Vpp, with spectral analysis of the base velocity placing a conservative lower bound of 36.2 m/s on this estimate. Large-signal failure-mode analysis identifies Pt/Au electrode melting at 210 Vpp as the current velocity ceiling. These results suggest that geometric amplification in high-order flexural modes offers a viable pathway toward the high proof-mass velocities targeted for next-generation MEMS inertial sensors.

0.29

Design and Physical Constraints of Synthetic-Frequency Photonic Switching Fabrics

cs.ET physics.optics ·2026-09-01 ·Jorge Parra
unusual similarity 0.49
Abstract · Main text (12 pages + 6 figures) and supplementary information (21 pages + 10 figures)

Electro-optic frequency conversion and synthetic-frequency coupling are established functions in integrated photonic devices. Their role within a multiport switching fabric, however, depends on how simultaneous optical connections share spatial paths, frequency channels, and device controls. Here, we investigate how coherent coupling among frequency modes can be incorporated into photonic switching fabrics and identify the corresponding architectural and physical constraints. We show that synthetic-frequency coupling does not increase the number of simultaneous orthogonal frequency channels when all channels are freely accessible, but can establish connections that are otherwise blocked by fixed input frequencies, channel-continuity requirements, or unavailable output channels. Under the tested conditions, coupling over the first three frequency spacings in an $8\times8$ fabric with eight frequency channels per port achieves 96.1% of the blocking reduction obtained with unrestricted inter-mode coupling. We further show that a separate frequency-only conversion stage cannot replace missing spatial connectivity. A nominal reduction in spatial switching elements instead requires a joint element whose spatial state can be programmed independently for each frequency channel. Finally, we evaluate a thin-film lithium niobate resonator model using reported electro-optic coupling and photon-decay scales within a multistage Mach-Zehnder interferometer switching fabric. These results clarify the architectural role of synthetic-frequency coupling and the device-level requirements for incorporating it into integrated photonic switching fabrics.

0.31

Analog Time-Frequency Analysis and Frequency Measurement of Ultra-Wideband Microwave Signals via Dual-Comb Channelization

eess.SP physics.optics ·2026-08-26 ·Taixia Shi, Wentao Ma, Fangzheng Zhang, Yang Chen
unusual similarity 0.46
Abstract · 21 pages, 12 figures

Frequency-to-time mapping (FTTM)-based photonics-assisted spectrum sensing enables wideband spectrum monitoring for applications such as cognitive radio and electronic warfare. However, FTTM-based photonics-assisted spectrum sensing approaches involve trade-offs among analysis bandwidth, temporal resolution, and frequency resolution. Although channelization has been introduced to alleviate these trade-offs, the limited number of available channels in previously reported systems constrains further improvements in overall performance. Here, we propose a photonics-assisted dual-comb channelization architecture for broadband frequency measurement and time-frequency analysis. The system employs a stepped-frequency pump based on stimulated Brillouin scattering (SBS) to generate an optical filter comb and adopts a single-laser design for the pump, probe, and reference paths to enhance frequency stability while reducing system complexity. Experimental results show a 48-GHz analysis bandwidth in the 16-channel configuration and 52 GHz in the 20-channel configuration, together with microsecond-scale temporal resolution and a frequency resolution better than 80 MHz. The proposed architecture therefore offers a practical and reconfigurable solution for real-time wideband spectrum sensing.

0.30

Low-Data OOD Prediction of SAW Resonators with Simulation-Compensated Transfer Learning

eess.SY ·2026-11-11 ·Zhijie Ma, Xingyu Liu, Shuhan Chen, Fangsheng Qian, Junyan Zheng +4 more
published similarity 0.43
Abstract

Surface acoustic wave (SAW) resonators are foundational to modern radio-frequency (RF) front-end architectures. However, models trained on limited fabricated devices generalize poorly to unmeasured design regions because of process-induced variations, while finite-element method (FEM) simulations, although inexpensive, exhibit systematic offsets from measurements. To predict device performance before physical prototyping, this work presents a simulation-compensated transfer-learning framework that uses computationally efficient 2.5-D FEM simulations as physics-based anchors and learns their calibration to the measurement domain. Using 4,236 measured lithium tantalate (LiTaO3) SAW resonators and 816 unique simulated configurations, five transfer strategies are systematically benchmarked under seven out-of-distribution (OOD) protocols spanning frequency, geometry, and material shifts. The proposed framework reduces OOD prediction error by 83.54% on average (up to 97.57%) relative to the Measurement-only baseline, with the best strategy selected per case, and raises the pooled R2 of frequency prediction to 1.000, offering an economically scalable route toward physics-guided, fabrication-aware machine learning for microelectromechanical-system (MEMS) acoustic-device design.

0.32

Modeling and Design of a Diaphragm-Integrated Photonic Waveguide Microphone

eess.AS ·2026-10-13 ·Xiaoyu Niu, Yuqi Meng, Zihuan Liu, Ehsan Vatankhah, Neal Hall
benchmark similarity 0.42
Abstract · 14 pages

Can an integrated optical readout improve the useful operating range of a miniature microphone? We address this question with an analytical model of a diaphragm carrying the sensing arm of a Mach-Zehnder interferometer (MZI). The model links pressure-induced bending to waveguide elongation and then to photocurrent, allowing mechanical sensitivity and optical detection limits to be assessed separately. Optical shot noise and back-cavity thermomechanical noise set the pressure resolution, while a 10% total harmonic distortion criterion defines acoustic overload. Two operating regimes are examined: a compact MEMS microphone with 1 mW optical input and a measurement microphone with 100 mW optical input. For the compact case, a 1 mm diameter, 1 micrometer thick, stress-free silicon diaphragm and 100% modulation efficiency give a predicted signal-to-noise ratio of 78 dB and acoustic overload pressure of 124 dB. The higher-power case lowers the modeled noise floor and increases dynamic range relative to the selected measurement microphone benchmark. These estimates rely on favorable assumptions and do not establish a substantial overall advantage in conventional microphone applications. Remote optical interrogation offers a separate motivation for harsh-environment sensing, but the temperature tolerance of the proposed sensing head remains unverified. The analysis identifies the design tradeoffs and measurements needed to test the predicted performance.

0.09