CS Paper Radar

Lithium Niobate Surface-Acoustic-Wave Resonator for Very-High-Frequency Isolated Power Conversion

Liyang Jin, Zhiyang Cao, Zichen Xi, Jun Ji, Yizheng Zhu, Liyan Zhu, Linbo Shao

eess.SY physics.app-ph ·submitted 2026-10-02 03:13 UTC · v1
unusual

Abstract

Piezoelectric devices offer a promising magnetic-free alternative for high-frequency power electronics, enabling compact energy transfer with inherent galvanic isolation. Here we demonstrate a lithium niobate surface acoustic wave (SAW) resonator that enables isolated power transfer and addresses the challenges in existing piezoelectric devices for power applications, including operation frequencies, power delivery figure of merit (FOM), power handling, and electrical isolation. Our application-optimized 40-MHz SAW resonator, with the two electrically isolated interdigital transducers (IDTs) and acoustic Bragg mirrors, achieves a 25.7 W output power at a less than 15 °C temperature rise with only passive cooling through the back mounting side, and an isolation voltage of 2.17 kV. In DC-AC power conversion, we demonstrate a peak efficiency of 93.8 %, a power delivery FOM of 13.47 mW/V$^2$ and a peak chip power density of 81.7 W/cm$^3$. DC-DC conversion is also demonstrated by connecting a diode rectifier to the output IDT, despite efficiency degrading to 52.7 %. Our results advance SAW devices as one of the core components for next-generation very-high-frequency, miniaturized, high-density, magnetic-free, isolated power converters.

Closest papers

Nearest neighbours by meaning across the whole index.

Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

eess.SP ·2026-11-09 ·Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu +6 more
similarity 0.59
Abstract · 8 pages, 11 figures

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm$^{2}$, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency ($k_{\mathrm{eff}}^{2}$) of 3% and a moderate static capacitance $C_0$ of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement ($ξ_{\mathrm{static}}$) of 145 nm/V and a high corresponding open-circuit sensitivity ($S_{\mathrm{OC}}$) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

0.33

20 ghz longitudinal surface acoustic wave resonators in 100-nm x-cut lithium niobate on silicon carbide

eess.SP ·2026-11-19 ·Jiajun Huang, Ziqian Yao, Tzu-Hsuan Hsu, Ian Anderson, Joshua Campbell +1 more
similarity 0.59
Abstract

Surface acoustic wave (SAW) resonators above 15~GHz require a fast acoustic mode that retains strong electromechanical coupling ($k^2$). This work reports longitudinal SAW (L-SAW) resonators designed for high $k^2$ in 100-nm X-cut lithium niobate (LN) on 4H silicon carbide (SiC), operating up to 21.7~GHz and reaching a $k^2$ of 8.1\%, a maximum Bode $Q$ of 70, and a figure of merit (FoM) of 5.7 at 20.24~GHz. In this thin-film waveguide, shrinking the wavelength ($λ$) keeps the normalized LN thickness ($h_\mathrm{LN}/λ$) large, sustaining both $k^2$ and acoustic confinement. Conversely, increasing $λ$ from 292 to 471~nm lowers $h_\mathrm{LN}/λ$ from 0.34 to 0.21 and raises the L-SAW phase velocity from 6.32 to 7.05~km/s, within 1.1\% of the 7126-m/s shear-wave velocity of 4H-SiC. As the velocity approaches this limit, more of the acoustic energy spreads into the non-piezoelectric SiC, and $k^2$ falls from its 8.1\% peak at $λ= 322$~nm to 1.7\% at $λ= 471$~nm. No L-SAW resonance is observed for $λ\geq 518$~nm ($h_\mathrm{LN}/λ\leq 0.19$), where the mode becomes leaky. Overall, the FoM stays within 5\% of its maximum for $h_\mathrm{LN}/λ$ between 0.26 to 0.31, defining a design window for L-SAW resonators in thin LN on SiC at K-band and beyond.

0.26

13,000-Fold Frequency Down Conversion From 280 MHz to 21 kHz Using Mechanical Frequency Combs

eess.SP ·2026-11-05 ·Ian Anderson, Zihuan Liu, Vivek Tallavajhula, Yen-Chen Wang, Tzu-Hsuan Hsu +2 more
unusual similarity 0.53
Abstract · 4 pages, 6 figures

Optical frequency combs bridge the microwave and terahertz regimes by down-converting terahertz optical energy into microwave signals. A photodetector converts the comb's equally spaced lines, generated through optical nonlinearities, into a low-frequency tone at their spacing. Here, we present the first mechanical version of this process, using mechanical frequency combs to downconvert energy over 4 orders of magnitude, from the MHz to kHz regime. Thin-film lithium niobate (LN) is used to design an acoustic resonator with a wide range of mode frequencies. We achieve phononic comb excitation from 250 MHz to 900 MHz and compare the electrical and laser Doppler vibrometer (LDV) measurements at 277 MHz. We then show the low-frequency spectrum of the devices, highlighting mechanical motion at the comb's spacing and demonstrating energy transfer from 277 MHz to 21 kHz.

0.30

Low-Data OOD Prediction of SAW Resonators with Simulation-Compensated Transfer Learning

eess.SY ·2026-11-11 ·Zhijie Ma, Xingyu Liu, Shuhan Chen, Fangsheng Qian, Junyan Zheng +4 more
published similarity 0.51
Abstract

Surface acoustic wave (SAW) resonators are foundational to modern radio-frequency (RF) front-end architectures. However, models trained on limited fabricated devices generalize poorly to unmeasured design regions because of process-induced variations, while finite-element method (FEM) simulations, although inexpensive, exhibit systematic offsets from measurements. To predict device performance before physical prototyping, this work presents a simulation-compensated transfer-learning framework that uses computationally efficient 2.5-D FEM simulations as physics-based anchors and learns their calibration to the measurement domain. Using 4,236 measured lithium tantalate (LiTaO3) SAW resonators and 816 unique simulated configurations, five transfer strategies are systematically benchmarked under seven out-of-distribution (OOD) protocols spanning frequency, geometry, and material shifts. The proposed framework reduces OOD prediction error by 83.54% on average (up to 97.57%) relative to the Measurement-only baseline, with the best strategy selected per case, and raises the pooled R2 of frequency prediction to 1.000, offering an economically scalable route toward physics-guided, fabrication-aware machine learning for microelectromechanical-system (MEMS) acoustic-device design.

0.32

Towards an Earpiece for Wearable and Dry Ultrasonic Vagus Nerve Stimulation

eess.SY ·2026-10-05 ·Sebastian Frey, Farouk Ghezraoui, Marc Nölke, Marco Giordano, Luca Benini +1 more
unusual similarity 0.43
Abstract · 4 pages, 3 figures

Ultrasound (US)-based auricular vagus nerve stimulation (aVNS) is emerging as a versatile, noninvasive modality for neuromodulation - spanning clinical therapies (e.g., pain management, depression) and general well-being applications. However, most existing US-based aVNS systems remain bulky and require wet coupling media (e.g., ultrasound gel) to achieve both spatially localized stimulation and efficient acoustic transmission. We present a wearable US stimulation system combining a personalized, dry-coupled earpiece with a battery-powered, wireless US probe. The earpiece integrates a 2 MHz piezoelectric transducer fully encapsulated in Humimic material designed for anatomical fit and stable coupling without externally applied gel. Hydrophone measurements of the fully encapsulated earpiece in water give a peak rarefactional pressure of 0.24 MPa at 15 mm for a 15 V unipolar excitation. We further demonstrate in vivo feasibility through fully dry, in-ear 2 MHz pulse-echo acquisitions under realistic wearing conditions, confirming effective US transmission without the need for coupling gel. These results demonstrate the integration of a personalized dry acoustic interface with battery-powered stimulation electronics, providing a wearable platform for investigating US-based aVNS. Future studies will focus on functional outcomes, including heart rate variability and pupillary responses during stimulation.

0.27

Bilayer Periodically Poled Piezoelectric Thin-Film Lithium Tantalate Platform for Passive-Layer-Free Flexural and Torsional Actuation

eess.SP ·2026-11-11 ·Tzu-Hsuan Hsu, Jiajun Huang, Zihuan Liu, Yen-Chen Wang, Vakhtang Chulukhadze +2 more
published similarity 0.42
Abstract · 4 pages, 7 figures, 1 table. Accepted to the 2027 IEEE 40th International Conference on Micro Electro Mechanical Systems (MEMS 2027)

This work demonstrates, to the best of our knowledge, the first passive-layer-free thin-film lithium tantalate (LT) actuator platform, supporting both out-of-plane flexural and in-plane torsional actuation from a single bilayer periodically poled piezoelectric film (P3F) X-cut LT stack. The polarity reversal across the bond interface flips the piezoelectric stress below the neutral axis, generating a bending moment without any passive elastic layer. Moreover, the two layers share identical elastic and thermal-expansion constants, making the stack thermally matched by construction. Suspended cantilever devices were fabricated on a single 2$\times$1.5 $μ$m X-cut LT stack and verified by laser Doppler vibrometry (LDV). The tapered flexural resonator exhibits a 5.5$\times$ tip velocity amplification and a measured peak tip velocity of 10.3 m/s at $Q=634$, and a 0.49 MHz torsional cantilever resonator with $Q=514$ is demonstrated on the same stack. These results position bilayer P3F LT as a thermally matched, passive-layer-free actuation platform for vacuum-operated and optically interrogated MEMS such as scanners, gyroscopes, and ultrasonic transducers.

0.37

High-Velocity Whip-Mode Microresonator in LTOI Unimorph: Measurement Methodology and Large-Signal Characterization

eess.SP ·2026-09-16 ·Tzu-Hsuan Hsu, Zihuan Liu, Harshvardhan Gupta, Ziqian Yao, Wei Wang +4 more
theoryunusual similarity 0.42
Abstract · 10 pages, 9 figures, 2 tables. Submitted to IEEE Journal of Microelectromechanical Systems

This paper presents the design, characterization, and large-signal measurement methodology of a high-order whip-mode flexural microresonator on a lithium tantalate-on-insulator (LTOI) unimorph platform. A tapered cantilever concentrates kinetic energy at the free tip through a structural velocity amplification effect, with a targeted whip mode at 9.175 MHz exhibiting a measured Q of 691 in air. The results indicate a substantially reduced susceptibility to viscous damping at high modal frequencies. In-air large-signal testing on a separate device confirms tip velocities up to 20 m/s before the reliable measurement range of the laser Doppler vibrometer (LDV) at the tapered tip is exceeded, while the device itself sustains drive levels up to 240 Vpp before failure. Transitioning to vacuum reveals photothermal-induced static bending of the LTOI cantilever under LDV laser illumination, an effect that prohibits direct velocity measurement for these resonators. Hence, it motivates an indirect extraction methodology to be implemented. In this work, a 3.85 times base-to-tip geometric amplification factor, independently calibrated at low drive, is applied to base velocity measurements to infer tip velocity under large-signal conditions. Using this approach with narrowband chirp excitation, a maximum extracted tip velocity of 58.9 m/s is obtained at 192 Vpp, with spectral analysis of the base velocity placing a conservative lower bound of 36.2 m/s on this estimate. Large-signal failure-mode analysis identifies Pt/Au electrode melting at 210 Vpp as the current velocity ceiling. These results suggest that geometric amplification in high-order flexural modes offers a viable pathway toward the high proof-mass velocities targeted for next-generation MEMS inertial sensors.

0.29

Analysis and Demonstration of a Current-Stiff, Isolated Capacitive Bridge Transformer

eess.SY ·2026-11-10 ·Patrick Nowakowski, Cameron Little, Mahima Gupta, Daniel C. Ludois
similarity 0.37
Abstract · 10 pages, 17 figures

The traditional Voltage Source Inverter (VSI) based Dual Active Bridge (DAB) utilizes a transformer at its center to provide galvanic isolation and a turns ratio for step up/down functionality. However, the transformer is often the limiting factor of the DAB, especially as semiconductor switching speeds improve, given steel core losses, winding losses, etc. This paper presents a new DAB architecture based on Current Source Inverters (CSIs) coupled through, and isolated by, an AC capacitive bridge, yielding a system called a Capacitive Bridge Transformer (CBT). The CBT architecture eliminates all magnetic components in the AC portion of the isolated DAB circuit, reducing frequency scaling barriers normally present in DABs. The paper introduces the CBT from the perspective of duality and then develops the DC-DC power flow equations, the internal apparent power equations, and effective turns ratio. The analytical models are verified by steady state and detailed time domain measurements on a 2 kW experimental prototype.

0.30