CS Paper Radar

Bilayer Periodically Poled Piezoelectric Thin-Film Lithium Tantalate Platform for Passive-Layer-Free Flexural and Torsional Actuation

Tzu-Hsuan Hsu, Jiajun Huang, Zihuan Liu, Yen-Chen Wang, Vakhtang Chulukhadze, Neal Hall, Ruochen Lu

eess.SP ·submitted 2026-11-11 21:54 UTC · v1
published

Abstract

This work demonstrates, to the best of our knowledge, the first passive-layer-free thin-film lithium tantalate (LT) actuator platform, supporting both out-of-plane flexural and in-plane torsional actuation from a single bilayer periodically poled piezoelectric film (P3F) X-cut LT stack. The polarity reversal across the bond interface flips the piezoelectric stress below the neutral axis, generating a bending moment without any passive elastic layer. Moreover, the two layers share identical elastic and thermal-expansion constants, making the stack thermally matched by construction. Suspended cantilever devices were fabricated on a single 2$\times$1.5 $μ$m X-cut LT stack and verified by laser Doppler vibrometry (LDV). The tapered flexural resonator exhibits a 5.5$\times$ tip velocity amplification and a measured peak tip velocity of 10.3 m/s at $Q=634$, and a 0.49 MHz torsional cantilever resonator with $Q=514$ is demonstrated on the same stack. These results position bilayer P3F LT as a thermally matched, passive-layer-free actuation platform for vacuum-operated and optically interrogated MEMS such as scanners, gyroscopes, and ultrasonic transducers.

Comment
4 pages, 7 figures, 1 table. Accepted to the 2027 IEEE 40th International Conference on Micro Electro Mechanical Systems (MEMS 2027)

Closest papers

Nearest neighbours by meaning across the whole index.

Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

eess.SP ·2026-11-09 ·Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu +6 more
similarity 0.64
Abstract · 8 pages, 11 figures

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm$^{2}$, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency ($k_{\mathrm{eff}}^{2}$) of 3% and a moderate static capacitance $C_0$ of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement ($ξ_{\mathrm{static}}$) of 145 nm/V and a high corresponding open-circuit sensitivity ($S_{\mathrm{OC}}$) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

0.33

High-Velocity Whip-Mode Microresonator in LTOI Unimorph: Measurement Methodology and Large-Signal Characterization

eess.SP ·2026-09-16 ·Tzu-Hsuan Hsu, Zihuan Liu, Harshvardhan Gupta, Ziqian Yao, Wei Wang +4 more
theoryunusual similarity 0.53
Abstract · 10 pages, 9 figures, 2 tables. Submitted to IEEE Journal of Microelectromechanical Systems

This paper presents the design, characterization, and large-signal measurement methodology of a high-order whip-mode flexural microresonator on a lithium tantalate-on-insulator (LTOI) unimorph platform. A tapered cantilever concentrates kinetic energy at the free tip through a structural velocity amplification effect, with a targeted whip mode at 9.175 MHz exhibiting a measured Q of 691 in air. The results indicate a substantially reduced susceptibility to viscous damping at high modal frequencies. In-air large-signal testing on a separate device confirms tip velocities up to 20 m/s before the reliable measurement range of the laser Doppler vibrometer (LDV) at the tapered tip is exceeded, while the device itself sustains drive levels up to 240 Vpp before failure. Transitioning to vacuum reveals photothermal-induced static bending of the LTOI cantilever under LDV laser illumination, an effect that prohibits direct velocity measurement for these resonators. Hence, it motivates an indirect extraction methodology to be implemented. In this work, a 3.85 times base-to-tip geometric amplification factor, independently calibrated at low drive, is applied to base velocity measurements to infer tip velocity under large-signal conditions. Using this approach with narrowband chirp excitation, a maximum extracted tip velocity of 58.9 m/s is obtained at 192 Vpp, with spectral analysis of the base velocity placing a conservative lower bound of 36.2 m/s on this estimate. Large-signal failure-mode analysis identifies Pt/Au electrode melting at 210 Vpp as the current velocity ceiling. These results suggest that geometric amplification in high-order flexural modes offers a viable pathway toward the high proof-mass velocities targeted for next-generation MEMS inertial sensors.

0.29

VecTile: A Low-Cost Flexible Tactile Array for 3-DoF Force Sensing

cs.RO ·2026-10-22 ·Jian Hou, Xin Zhou, Adam J. Spiers
similarity 0.46
Abstract · 8 pages, 8 figures. Submitted to IEEE International Conference on Robotics and Automation (ICRA) 2027

Tactile sensing provides robots with contact information difficult to obtain from vision alone. Shear force is particularly important for understanding tangential contact, guiding corrective motions, and maintaining grasp stability, yet flexible and low-cost tactile arrays often measure only normal force. We introduce VecTile, a low-cost, 6 mm thin, flexible tactile array capable of three-axis force sensing. VecTile combines a piezoresistive layer with passive silicone nubs that convert normal and shear forces into distinguishable pressure patterns. The sensor can be fabricated in-house without specialized equipment. The complete system costs less than 35 USD for a 4x4 array. We validate the sensing mechanism through finite element analysis and hardware experiments. In controlled single-taxel tests over 1-5 N normal force and up to 1.5 N shear force, VecTile achieves root-mean-square errors of 0.39 N and 0.16 N for normal and shear forces. A VecTile calibrated while flat retains accuracy when curved, while a five-minute manual calibration is sufficient for practical use. Two applications demonstrate its utility. First, shear readings are sensitive enough to stop a sharp scalpel from puncturing a balloon after contact. Second, the sensor substantially improves Diffusion Policy-guided power-plug insertion. All designs and code will be released upon paper acceptance. Project website: https://jiannnh.github.io/VecTile/.

0.20

Tip Manipulation in Soft Everting Robots via Wall Retraction and Deployable Fingers

cs.RO ·2026-09-19 ·Nelson Badillo Perez, Niccolo Pagliarani, Matteo Cianchetti, Robert D. Howe
similarity 0.44
Abstract · 38 pages, 6 figures and supplementary information

Soft everting robots can traverse long, confined paths by continuously growing, yet active interaction remains limited to a single tool fixed at or near the tip, unable to be repositioned on demand and difficult to reconcile with the robot's soft body. We introduce a tip-manipulation and multi-tool deployment strategy for soft everting robots based on wall retraction, implemented with a base roller assembly that independently meters membrane flow in the outer wall while a tail spool regulates growth in the internal tail section. Coordinated wall and tail actuation decouples robot length from membrane-material position, enabling membrane-mounted devices to be transported, exposed, and repositioned at selected locations near the distal tip. We pair this capability with ultralight pleated inflatable fingers integrated into the membrane, fabricated from TPU-coated nylon with an internal airtight bladder. The fingers achieve large bending at low pressures (approximately 100 degrees at 50 kPa in high-pleat designs) and generate blocking forces up to 1.9 N, while remaining limp during transport. The system demonstrates adaptive grasping across diverse household objects (21 to 550 g; 16 to 200 mm), three-dimensional object manipulation and stacking, environmentally braced extension, distal camera panning for confined-space inspection, and controlled sequential payload delivery. These results enable embodied and reversible tip manipulation for soft growing robots in cluttered and tortuous environments.

0.25

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.44
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

Design and Experimental Validation of a 3D Printed Torsional Series Elastic Actuator for Safe Human Robot Interaction

cs.RO ·2026-09-16 ·Joel Hidalgo Pisco, Melissa Cobos Condo, Luigi Miranda, Dennys Paillacho
published similarity 0.44
Abstract

Ensuring intrinsic safety in physical human robot interaction (pHRI) is a critical requirement for social and service robots. While Series Elastic Actuators (SEAs) offer hardware based compliance, traditional metallic designs often require complex, multi part assemblies. This paper presents the design, finite element analysis (FEA), and experimental validation of a low stiffness, torsional spring for SEAs, manufactured via 3D printed thermoplastic polyurethane (TPU). The compliant element exhibits a highly linear torque deformation response (Ks = 0.066 Nm/degree), matching numerical predictions with under 3% deviation, a variance attributed to FDM structural anisotropy. To accommodate external interactions using standard position limited servomotors, a hybrid position controller with torque threshold switching was implemented. Experimental evaluations demonstrate the system ability to accurately track non stationary trajectories and safely yield to external disturbances. Furthermore, the inherent material damping of the TPU acts as a passive low pass filter, preventing high frequency oscillations during control mode transitions. The proposed architecture offers a cost effective, reliable, and easily manufacturable solution for safe pHRI.

0.32

Towards insect-like distributed proprioception in actuators and appendages for flapping-wing insect-scale aerial robots

cs.RO ·2026-08-22 ·Alexander Hedrick, Arvind Gupta, Kaushik Jayaram
similarity 0.42
Abstract · 8 pages, 6 figures, this work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after wh…

Modern flapping-wing insect-scale air vehicles display agility similar to that of their insect counterparts; however, these impressive maneuvers are only possible with off-board sensors like optical tracking cameras. In this manuscript, we introduce two embedded proprioceptive sensors for insect-scale aerial robots: thin film piezoelectric polymers integrated directly into a driving actuator and a pitching hinge which track stroke and pitch angle, respectively. We fabricate the aforementioned size-agnostic mechanically intelligent structures (sensor-actuator, sensor-flexure) using laminate stack fabrication methods. Chirp experiments with our sensors integrated into an insect-size flapping-wing robot show accurate tracking of stroke (RMSE = 0.44 deg) and pitch (RMSE = 2.44 deg) angles in the relevant frequency range. As the first step towards demonstrating the utility of these sensors for enabling numerous onboard autonomy applications, including closed-loop wingbeat control and sensor fusion with existing insect-scale sensor suites for more accurate proprioception and localization, we show one application for each sensor. The proprioceptive hinge enables collision detection, reducing the chance of permanent damage if the robot's wing collides with an object. The proprioceptive actuator enables asynchronous flapping, which is hypothesized to increase adaptability and efficiency in insects and robots alike. A microrobot equipped with our proprioceptive actuator allows us to test these hypotheses with potential for improving flapping aerial robot performance. We foresee proprioceptive sensors having an important role in progressing both the fields of insect-scale aerial robots and robo-physics due to the bio-inspired nature and high integration level of our sensors.

0.27

Lithium Niobate Surface-Acoustic-Wave Resonator for Very-High-Frequency Isolated Power Conversion

eess.SY physics.app-ph ·2026-10-02 ·Liyang Jin, Zhiyang Cao, Zichen Xi, Jun Ji, Yizheng Zhu +2 more
unusual similarity 0.42
Abstract

Piezoelectric devices offer a promising magnetic-free alternative for high-frequency power electronics, enabling compact energy transfer with inherent galvanic isolation. Here we demonstrate a lithium niobate surface acoustic wave (SAW) resonator that enables isolated power transfer and addresses the challenges in existing piezoelectric devices for power applications, including operation frequencies, power delivery figure of merit (FOM), power handling, and electrical isolation. Our application-optimized 40-MHz SAW resonator, with the two electrically isolated interdigital transducers (IDTs) and acoustic Bragg mirrors, achieves a 25.7 W output power at a less than 15 °C temperature rise with only passive cooling through the back mounting side, and an isolation voltage of 2.17 kV. In DC-AC power conversion, we demonstrate a peak efficiency of 93.8 %, a power delivery FOM of 13.47 mW/V$^2$ and a peak chip power density of 81.7 W/cm$^3$. DC-DC conversion is also demonstrated by connecting a diode rectifier to the output IDT, despite efficiency degrading to 52.7 %. Our results advance SAW devices as one of the core components for next-generation very-high-frequency, miniaturized, high-density, magnetic-free, isolated power converters.

0.26