CS Paper Radar

20 ghz longitudinal surface acoustic wave resonators in 100-nm x-cut lithium niobate on silicon carbide

Jiajun Huang, Ziqian Yao, Tzu-Hsuan Hsu, Ian Anderson, Joshua Campbell, Ruochen Lu

eess.SP ·submitted 2026-11-19 02:49 UTC · v1

Abstract

Surface acoustic wave (SAW) resonators above 15~GHz require a fast acoustic mode that retains strong electromechanical coupling ($k^2$). This work reports longitudinal SAW (L-SAW) resonators designed for high $k^2$ in 100-nm X-cut lithium niobate (LN) on 4H silicon carbide (SiC), operating up to 21.7~GHz and reaching a $k^2$ of 8.1\%, a maximum Bode $Q$ of 70, and a figure of merit (FoM) of 5.7 at 20.24~GHz. In this thin-film waveguide, shrinking the wavelength ($λ$) keeps the normalized LN thickness ($h_\mathrm{LN}/λ$) large, sustaining both $k^2$ and acoustic confinement. Conversely, increasing $λ$ from 292 to 471~nm lowers $h_\mathrm{LN}/λ$ from 0.34 to 0.21 and raises the L-SAW phase velocity from 6.32 to 7.05~km/s, within 1.1\% of the 7126-m/s shear-wave velocity of 4H-SiC. As the velocity approaches this limit, more of the acoustic energy spreads into the non-piezoelectric SiC, and $k^2$ falls from its 8.1\% peak at $λ= 322$~nm to 1.7\% at $λ= 471$~nm. No L-SAW resonance is observed for $λ\geq 518$~nm ($h_\mathrm{LN}/λ\leq 0.19$), where the mode becomes leaky. Overall, the FoM stays within 5\% of its maximum for $h_\mathrm{LN}/λ$ between 0.26 to 0.31, defining a design window for L-SAW resonators in thin LN on SiC at K-band and beyond.

Closest papers

Nearest neighbours by meaning across the whole index.

Lithium Niobate Surface-Acoustic-Wave Resonator for Very-High-Frequency Isolated Power Conversion

eess.SY physics.app-ph ·2026-10-02 ·Liyang Jin, Zhiyang Cao, Zichen Xi, Jun Ji, Yizheng Zhu +2 more
unusual similarity 0.59
Abstract

Piezoelectric devices offer a promising magnetic-free alternative for high-frequency power electronics, enabling compact energy transfer with inherent galvanic isolation. Here we demonstrate a lithium niobate surface acoustic wave (SAW) resonator that enables isolated power transfer and addresses the challenges in existing piezoelectric devices for power applications, including operation frequencies, power delivery figure of merit (FOM), power handling, and electrical isolation. Our application-optimized 40-MHz SAW resonator, with the two electrically isolated interdigital transducers (IDTs) and acoustic Bragg mirrors, achieves a 25.7 W output power at a less than 15 °C temperature rise with only passive cooling through the back mounting side, and an isolation voltage of 2.17 kV. In DC-AC power conversion, we demonstrate a peak efficiency of 93.8 %, a power delivery FOM of 13.47 mW/V$^2$ and a peak chip power density of 81.7 W/cm$^3$. DC-DC conversion is also demonstrated by connecting a diode rectifier to the output IDT, despite efficiency degrading to 52.7 %. Our results advance SAW devices as one of the core components for next-generation very-high-frequency, miniaturized, high-density, magnetic-free, isolated power converters.

0.26

Toward Ku-Band Surface Acoustic Wave Delay Lines on AlScN-on-Diamond with Decoupled Phase and Group Velocities

eess.SP ·2026-09-15 ·Tzu-Hsuan Hsu, Kapil Saha, Yuchen Ma, Vakhtang Chulukhadze, Pietro Simeoni +2 more
unusual similarity 0.59
Abstract · 4 pages, 8 figures, submitted to IEEE IUS 2026 conference

This work reports surface acoustic wave (SAW) acoustic delay lines (ADLs) on an aluminum scandium nitride (AlScN) on diamond platform operating in the X band and approaching the Ku band. The large acoustic-velocity contrast between the AlScN film and the diamond substrate produces a strongly dispersive Sezawa branch that decouples the phase velocity from the group velocity. Delay lines with a 1 $μ$m wavelength show a Sezawa passband at 9.55 GHz with a fractional bandwidth of 1.05%, a propagation loss of 0.094 dB per wavelength, a propagation-limited quality factor of 465, and a group velocity of 5979 m/s, while co-fabricated resonators give a phase velocity of 9560 m/s, a ratio of about 1.6. Scaling the wavelength to 0.5 $μ$m moves the passband to 16.5 GHz with a fractional bandwidth of 0.7%. The platform therefore reaches an operating frequency about 1.5 times higher than AlScN on sapphire at the same lithographic pitch while preserving group delay per unit length.

0.27

Low-Data OOD Prediction of SAW Resonators with Simulation-Compensated Transfer Learning

eess.SY ·2026-11-11 ·Zhijie Ma, Xingyu Liu, Shuhan Chen, Fangsheng Qian, Junyan Zheng +4 more
published similarity 0.58
Abstract

Surface acoustic wave (SAW) resonators are foundational to modern radio-frequency (RF) front-end architectures. However, models trained on limited fabricated devices generalize poorly to unmeasured design regions because of process-induced variations, while finite-element method (FEM) simulations, although inexpensive, exhibit systematic offsets from measurements. To predict device performance before physical prototyping, this work presents a simulation-compensated transfer-learning framework that uses computationally efficient 2.5-D FEM simulations as physics-based anchors and learns their calibration to the measurement domain. Using 4,236 measured lithium tantalate (LiTaO3) SAW resonators and 816 unique simulated configurations, five transfer strategies are systematically benchmarked under seven out-of-distribution (OOD) protocols spanning frequency, geometry, and material shifts. The proposed framework reduces OOD prediction error by 83.54% on average (up to 97.57%) relative to the Measurement-only baseline, with the best strategy selected per case, and raises the pooled R2 of frequency prediction to 1.000, offering an economically scalable route toward physics-guided, fabrication-aware machine learning for microelectromechanical-system (MEMS) acoustic-device design.

0.32

13,000-Fold Frequency Down Conversion From 280 MHz to 21 kHz Using Mechanical Frequency Combs

eess.SP ·2026-11-05 ·Ian Anderson, Zihuan Liu, Vivek Tallavajhula, Yen-Chen Wang, Tzu-Hsuan Hsu +2 more
unusual similarity 0.55
Abstract · 4 pages, 6 figures

Optical frequency combs bridge the microwave and terahertz regimes by down-converting terahertz optical energy into microwave signals. A photodetector converts the comb's equally spaced lines, generated through optical nonlinearities, into a low-frequency tone at their spacing. Here, we present the first mechanical version of this process, using mechanical frequency combs to downconvert energy over 4 orders of magnitude, from the MHz to kHz regime. Thin-film lithium niobate (LN) is used to design an acoustic resonator with a wide range of mode frequencies. We achieve phononic comb excitation from 250 MHz to 900 MHz and compare the electrical and laser Doppler vibrometer (LDV) measurements at 277 MHz. We then show the low-frequency spectrum of the devices, highlighting mechanical motion at the comb's spacing and demonstrating energy transfer from 277 MHz to 21 kHz.

0.30

Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

eess.SP ·2026-11-09 ·Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu +6 more
similarity 0.49
Abstract · 8 pages, 11 figures

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm$^{2}$, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency ($k_{\mathrm{eff}}^{2}$) of 3% and a moderate static capacitance $C_0$ of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement ($ξ_{\mathrm{static}}$) of 145 nm/V and a high corresponding open-circuit sensitivity ($S_{\mathrm{OC}}$) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

0.33

High-Velocity Whip-Mode Microresonator in LTOI Unimorph: Measurement Methodology and Large-Signal Characterization

eess.SP ·2026-09-16 ·Tzu-Hsuan Hsu, Zihuan Liu, Harshvardhan Gupta, Ziqian Yao, Wei Wang +4 more
theoryunusual similarity 0.44
Abstract · 10 pages, 9 figures, 2 tables. Submitted to IEEE Journal of Microelectromechanical Systems

This paper presents the design, characterization, and large-signal measurement methodology of a high-order whip-mode flexural microresonator on a lithium tantalate-on-insulator (LTOI) unimorph platform. A tapered cantilever concentrates kinetic energy at the free tip through a structural velocity amplification effect, with a targeted whip mode at 9.175 MHz exhibiting a measured Q of 691 in air. The results indicate a substantially reduced susceptibility to viscous damping at high modal frequencies. In-air large-signal testing on a separate device confirms tip velocities up to 20 m/s before the reliable measurement range of the laser Doppler vibrometer (LDV) at the tapered tip is exceeded, while the device itself sustains drive levels up to 240 Vpp before failure. Transitioning to vacuum reveals photothermal-induced static bending of the LTOI cantilever under LDV laser illumination, an effect that prohibits direct velocity measurement for these resonators. Hence, it motivates an indirect extraction methodology to be implemented. In this work, a 3.85 times base-to-tip geometric amplification factor, independently calibrated at low drive, is applied to base velocity measurements to infer tip velocity under large-signal conditions. Using this approach with narrowband chirp excitation, a maximum extracted tip velocity of 58.9 m/s is obtained at 192 Vpp, with spectral analysis of the base velocity placing a conservative lower bound of 36.2 m/s on this estimate. Large-signal failure-mode analysis identifies Pt/Au electrode melting at 210 Vpp as the current velocity ceiling. These results suggest that geometric amplification in high-order flexural modes offers a viable pathway toward the high proof-mass velocities targeted for next-generation MEMS inertial sensors.

0.29

Time-Domain Analysis of Surface Acoustic Wave Magnetoelectric Sensors

eess.SY physics.app-phcond-mat.mtrl-sci ·2026-10-08 ·Mohsen Samadi, Henrik Wolframm, Felix Weisheit, Dirk Meyners, Eckhard Quandt +2 more
unusual similarity 0.42
Abstract · 18 pages, 6 figures, 1 table

The transient response of surface acoustic wave sensors is important for understanding their dynamic behavior, propagation delay, and response to time-varying signals. In this work, the time-domain propagation characteristics of a magnetoelectric SAW sensor based on a multilayer Love-wave delay line are investigated using complementary numerical and experimental approaches. Time-domain analysis is employed to determine the delay time and to extract the phase and group velocities, while frequency-domain analysis provides an independent characterization of the wave dispersion. Both numerically and experimentally, the phase and group velocities are found to differ, reflecting the dispersion of the Love wave in the multilayer structure. At the operating frequency of 146 MHz, the simulated group velocity obtained from wave-field tracking agrees within 0.4% with the value determined from the frequency-domain dispersion relation. The simulated delay time and group velocity also show good agreement with experiment, with deviations of 2.7% in delay time and 0.9% in group velocity. These results demonstrate the consistency of the time- and frequency-domain analyses and provide a quantitative characterization of the transient propagation behavior of SAW sensors.

0.29

Performance Analysis and Design of an Optomechanical Microphone Using an Integrated Photonic Waveguide Interferometer

eess.AS eess.SYphysics.app-ph ·2026-09-21 ·Xiaoyu Niu, Yuqi Meng, Zihuan Liu, Ehsan Vatankhah, Neal Hall
unusual similarity 0.41
Abstract · 16 pages, 12 figures, 1 table

We present an optomechanical microphone based on a diaphragm-integrated photonic waveguide Mach-Zehnder interferometer. Acoustic pressure deforms the MEMS diaphragm, inducing strain in the sensing waveguide and changing its optical path length. We analytically evaluate the optical and mechanical transduction mechanisms and key figures of merit, including signal-to-noise ratio, dynamic range, acoustic overload pressure, and minimum detectable pressure. Two design cases are considered: a MEMS microphone and a measurement microphone. The results indicate competitive performance but no substantial overall advantage over state-of-the-art microphones in conventional applications. The architecture may nevertheless offer advantages for high-temperature and other harsh-environment sensing applications.

0.30