CS Paper Radar

Measurements and Analysis of Distortion in Inertial Force Exciters for Flat-Panel Loudspeakers

Stephen F. Roessner, Michael C. Heilemann

eess.SY ·submitted 2026-10-13 19:59 UTC · v1
publishedunusual

Abstract

Flat-panel loudspeakers are typically driven by dynamic exciters that employ a voice coil coupled to a reaction mass to exert force on the panel. Unlike conventional loudspeakers, where the cone is relatively light weight, heavy panels may require significant exertion from the driver to achieve sound pressure levels required of consumer grade loudspeakers. Overexertion can cause harmonic distortion and reduced sound quality, especially in drivers where the voice coil is not centered in the magnetic field. There are many different exciters available commercially with different power ratings and price points. The frequency response, linearity, total-harmonic distortion (THD), intermodulation distortion (IMD), and force vs. displacement were measured for three types of exciters to determine the consistency of manufacturing and use in panel loudspeakers. These exciters were found to have high variability in all metrics among units of the same type. Distortion metrics such as IMD may be reduced by running impedance sweeps to match exciters with similar response characteristics in multi-actuator panels.

Comment
Accepted to 161st Convention of the Audio Engineering Society, Nashville, TN, USA, Oct. 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Passive ladder-network representation of the radiation impedance of a spherical cap on a rigid sphere

eess.AS physics.class-ph ·2026-11-10 ·Ronald M. Aarts
unusual similarity 0.42
Abstract · 13 pages (preprint format), 3 figures. Submitted to JASA Express Letters

A loudspeaker in a closed box is modeled as a rigid sphere with an axially moving cap. For an axisymmetric cone-velocity profile, its radiation impedance is written as a network. Each spherical-harmonic mode has an impedance rational in frequency, realized exactly as a finite passive ladder of masses and compliances terminated in a resistance. Ideal transformers set by Legendre coefficients couple these ladders; truncated modes reduce to a residual mass. Despite the different geometry, the impedance resembles that of a baffled piston but, at equal volume velocity, has half its low-frequency resistance and about three quarters of its radiation mass.

0.27

High-Voltage Optocoupler Amplifier for Electrostatic Actuators

cs.RO eess.SYphysics.ins-det ·2026-09-24 ·George C. Jurgiel, Alex S. Miller, Jeffrey H. Lang
publishedunusual similarity 0.41
Abstract · To be published in the proceedings of the 2026 IEEE Energy Conversion Congress & Expo (ECCE)

Many electrostatic actuators require multi-kilovolt drive voltages at sub-milliamp currents, a task poorly suited for conventional switching devices. As an alternative, we demonstrate a high-voltage amplifier using optocouplers as active elements. The amplifier produces a 20-kV peak-to-peak output with up to 500 Hz bandwidth while maintaining a minimal component count. By using optocouplers as linear devices in feedback, lower harmonic distortion and higher bandwidth are achieved than offered by equivalent PWM amplifiers. This design improves the viability of electrostatic actuators by providing a simpler method to achieve useful drive waveforms.

0.58

Frequency-Weighted Soft-Constrained Spatially Selective Active Noise Control for Open-Fitting Hearables

eess.AS eess.SP ·2026-09-30 ·Tong Xiao, Reinhild Roden, Matthias Blau, Simon Doclo
similarity 0.39
Abstract · 5 pages, 4 figures, 1 table. Submitted to IEEE ICASSP 2027

Recently, soft-constrained spatially selective active noise control (SSANC) for open-fitting hearables has been proposed to enable a flexible trade-off between noise reduction and desired-speech preservation using a scalar trade-off parameter across all frequencies. This paper generalizes soft-constrained SSANC by introducing frequency-dependent weighting of the desired-speech preservation error while maintaining low-delay time-domain active control. Frequency-dependent weightings based on the speech intelligibility index (SII), the modified intermediate reference system (MIRS), the long-term average speech spectrum (LTASS), and a signal-dependent oracle are compared with scalar weighting using measured acoustic impulse responses in a multi-speaker scenario. The results show that LTASS and oracle weightings provide the largest speech-intelligibility improvements and comparable speech-quality improvements at substantially lower distortion levels than those obtained with SII and MIRS weightings. While the oracle weighting provides the best overall perceptual trade-off, LTASS weighting provides a comparable perceptual trade-off without requiring the clean desired-speech signal.

0.23

Side-Vent Design for Microphone-Based Mechanomyography Sensors: Modeling and Experimental Evaluation of Contact Dependence

cs.HC ·2026-10-11 ·Cong Liu, Xiao Jin, Zhenhua Yu
similarity 0.39
Abstract · 10 pages, 9 figures, 1 table. Submitted to IEEE Sensors Journal

Wearable muscle sensing for rehabilitation, assistive robotics, and electrical-stimulation feedback needs mechanomyography sensors less sensitive to fit changes during wear. In microphone-based mechanomyography, cavity pressure depends on rim contact, a dependence housing design has rarely targeted. This study evaluates a side-vented housing, whose vent opens a pressure-relief path in parallel with the rim to lower contact dependence, and quantifies the acoustic-gain cost. Thermoviscous finite-element simulations compared twenty cavity configurations under prescribed source motion. Paired bench sweeps over 10-200 Hz on both housings compared direct contact with a Gap-ring spacer, a radially grooved spacer ring. At 100 Hz, side venting reduced the simulated acoustic-gain variation across 0.10-0.50 mm rim clearances from 25.8 to 10.0 dB and cost 5.5 dB of gain at 0.20 mm clearance. Velocity fields and branch-flow calculations identified this path. At the higher speaker drive level, the Gap-ring spacer caused median attenuations of 13.6 dB (vented) and 30.1 dB (unvented) relative to direct contact. In this front end, a 35.9-dB signal-gain increase at 100 Hz raised the calculated operational-amplifier voltage-noise gain by 1.6 dB. A single-participant demonstration of paced elbow flexion and extension compared envelope timing and spectra between housings, finding similar envelope timing (correlation 0.935) and broadly similar spectra (correlation 0.956). Vent area trades acoustic gain against contact dependence and can therefore serve as a housing design parameter.

0.31

Neural topology optimization of ship structures under propulsion machinery vibrations

cs.CE cs.AIcs.LGmath.NA+1 ·2026-09-29 ·Shengyu Yan, Muhammad Muztahidul Hakim Zareer, Jasmin Jelovica
similarity 0.37
Abstract · 24 pages, 13 figures, 7 tables

Ship structural vibrations contribute to noise, fatigue, and equipment damage, while dynamic-compliance topology optimization can produce pathological designs near resonance. This study extends neural-reparameterized topology optimization using a convolutional Kolmogorov-Arnold network (KATO) to forced-vibration design with active input power (AIP) as the objective. Applications include a 100 Hz engine-supporting deck panel and an 18 Hz thruster foundation frame. Helmholtz PDE filtering and Heaviside projection control feature sizes and manufacturing tolerance. Across both deck families, all eight optimized layouts reduce AIP relative to size-optimized references and, after finite-depth extrusion, also achieve lower static compliance. For unrestricted, manufacturing-aware, and stress-aware frame variants, KATO matches GCMMA in AIP within 0.5 dB while yielding 22-36x lower static compliance after matched-volume binary re-analysis. In a near-resonant 300 Hz case, both methods reduce initial AIP by more than 32 dB; KATO maintains a connected design, achieves 59x lower binary static compliance, and reduces maximum AIP over 1-500 Hz by 2.7 dB. KATO runs 6.4-10.4x faster than GCMMA for the implemented stress-aware formulations. The results demonstrate neural AIP-driven topology optimization as an efficient approach for designing connected, feature-size-controlled ship structures with improved forced-vibration performance.

0.30

Sensing Bone-Conducted Speech with Earbuds

eess.AS ·2026-09-02 ·Christoph Weyer, Peter Jax
published similarity 0.37
Abstract · 14 pages, 12 figures, journal

Clear capture of the wearer's own voice (OV) is essential when using earbuds for mobile communication. However, OV capture remains challenging in noisy environments. Bone-conducted (BC) speech, which can be sensed as vibrations of the earbud housing, can be used to improve OV capture. However, neither bandwidth nor spatial characteristics of OV-induced earbud vibrations have been analyzed in detail, despite both characteristics being relevant, e.g., for sensor choice and placement. This study investigates both characteristics, based on measurements with two earbud models. Spectrally, results indicate that OV-induced earbud vibrations exhibit a low-pass characteristic, with a steep roll-off of -93 dB per decade above 400 Hz. Thus, sensors with comparatively low noise floors are required to sense the vibrations above \SI{1}{\kilo\hertz}. Spatially, results indicate that the earbuds mainly vibrate in and out of the ear canal entrance, with high consistency between subjects and fits. Simulations confirm that this enables capture of the high-power vibrations below 400 Hz by a single-axis sensor with less than 1.5 dB mean attenuation.

0.39

Reproduction of Simulated Acoustics Scenes Using Acoustics Room Transformer for speech intelligibility tests in Clinics

eess.AS physics.med-ph ·2026-11-13 ·Ali Fallah, Kirsten C Wagener, Pascal Pflueger, Steven van de Par
similarity 0.37
Abstract · This paper is submitted to Acta Acustica and is currently under review

An Acoustic Room Transformation (ART) method is proposed for clinical applications to render simulated acoustic environments using six loudspeakers in a reverberant room. In typical clinical settings, testing rooms are not acoustically treated and only a limited number of loudspeakers are available. The ART approach enables control of the playback-room reverberation, allowing speech intelligibility tests to be performed under realistic and perceptually compensated conditions. The method focuses on the two most common Speech Reception Threshold (SRT) configurations: S0N90 and S0N90. One front and one side loudspeaker reproduce the direct sound components, while the remaining four loudspeakers (two in front and two behind the listener) generate the reverberant sound field. The direct sound is optimized in terms of energy, and the reverberant field is adjusted based on both energy and interaural coherence. An additional direct-sound gain is applied to match the clarity index (C50) of the reproduced signals to that of the reference target. Results from speech intelligibility tests demonstrate that, with ART processing, the reproduced scenarios achieve SRT values very close to those of the reference signal in both S0N0 and S0N90 conditions and therefore allow for comparable speech test results independent of the particular test room acoustics.

0.27

Ultrasound Elastography: Excitation Methods and Low-Cost Alternative

cs.CV eess.IV ·2026-11-11 ·Corin F. Otesteanu
published similarity 0.36
Abstract

Ultrasound elastography (or elasticity imaging) is a method that characterizes the tissue mechanical properties with the purpose of aiding the diagnosis of certain pathologies. Many novel clinical applications use the assumption that these tissue properties are changed in the presence of pathological processes. Characterization of tissue mechanical properties is achieved by imaging the response of the tissue to an induced stress or excitation. A plethora of approaches have been used in the scientific community to induce excitation in tissue, which usually require additional tools or devices than are costly. Furthermore these are usually integrated in the imaging pipeline using additional software or hardware for control. An alternative that is simpler, faster to integrate (and low-cost) is proposed in this work, by using readily available smartphones as a source of mechanical excitation. The induced displacements are used to solve the elasticity inverse problem (IP) using a finite element method (FEM) approach. Preliminary elasticity reconstructions of a phantom that mimics tissue are similar to when using a dedicated actuator as means of inducing harmonic displacements, illustrating the feasibility of our low-cost ultrasound elasography approach.

0.36