CS Paper Radar

CBF-Based Control Allocation for Omnidirectional Tiltrotor Aerial Robots

Seobeom Lee, Hyondong Oh

cs.RO ·submitted 2026-10-15 15:22 UTC · v1

Abstract

Actively tilting aerial robots can generate six-dimensional wrenches, but slow servo response can make a desired wrench infeasible during reconfiguration. This paper develops a control barrier function (CBF) allocator that preserves wrench feasibility under bounded servo-configuration mismatch. An exact equivalent-wrench identity connects the thrust required at nominal and actual configurations. For a nonsingular six-channel allocation map, inverse allocation reduces robust wrench containment to twelve thrust margins tightened by an ellipsoidal reserve. Their complete derivatives yield a six-variable servo-rate quadratic program, followed by differential thrust allocation for tracking. A conditional forward-invariance result establishes actual-configuration feasibility under reserve coverage, feasible initialization, and admissible CBF inputs. A complementary MuJoCo study evaluates a measured-angle implementation against geometric, augmented differential, and normalized differential allocation in circular and cartwheel maneuvers, with and without disturbances. The proposed implementation achieves lower position error in all four recorded scenarios, with an attitude tradeoff in circular tracking. During the disturbed cartwheel, the desired wrench is feasible at all 1751 stored samples of continuous rotation; baseline violation rates range from 60.8% to 100%. These comparisons evaluate sampled feasibility; validation of the nominal-trajectory certificate requires nominal-state and reserve-coverage records.

Comment
11 pages

Closest papers

Nearest neighbours by meaning across the whole index.

Effector-Centric NMPC of Tiltable-Multirotors for Offset-Free Omnidirectional Aerial Manipulation

cs.RO ·2026-08-18 ·Jinjie Li, Yicheng Chen, Johannes Kübel, Haokun Liu, Junichiro Sugihara +1 more
top venue similarity 0.74
Abstract · 22 pages, 26 figures. Accepted to IEEE Transactions on Robotics (T-RO). This arXiv version includes a two-page appendix with additional impl…

Aerial manipulation extends robotic operations to previously inaccessible aerial environments. Unlike arm-equipped aerial systems, tiltable-multirotors can directly generate six-degree-of-freedom wrenches through their flight bases, enabling both efficient movement and omnidirectional operation by tilting the thrust direction. This work presents a design analysis and a wrench-based control framework for tiltable-multirotors in aerial manipulation. We show that a four-rotor tiltable configuration provides a balance between interference-free propeller sizing and hovering efficiency across different attitudes, and its null-space redundancy is crucial for traversing singular configurations under physical constraints. We further show that an upward end-effector placement yields a favorable trade-off between geometric clearance and available wrench. To address disturbances, we propose a dual strategy consisting of a modified integral term for model error and an acceleration-based estimator for external wrenches. Building on these insights, we develop an effector-centric nonlinear model predictive control (NMPC) framework that integrates design choices, singularity handling, and disturbance compensation into a unified formulation. The proposed framework runs fully onboard at 100 Hz on a custom-built tiltable-quadrotor. Real-world experiments, including a 90-deg step cartwheel rotation, whiteboard pushing, and continuous 360-deg valve turning, demonstrate the feasibility of wrench-based omnidirectional manipulation with singularity traversal on a one-DoF-per-arm tiltable-quadrotor.

0.51

Tilt as a Certified Resource: Preserving Motor Wrench-Rate Authority on Articulated Multirotors

cs.RO eess.SYmath.OC ·2026-09-18 ·Giuseppe Silano, Martin Saska
similarity 0.68
Abstract · This work has been submitted to the IEEE for possible publication

Fully-actuated multirotor aerial vehicles must not only track nominal wrenches but retain the "readiness" to modulate them rapidly under disturbances. Classical effort-minimizing allocators ignore this dynamic limit, whereas maximizing readiness leads to topologically disconnected optimal sheets demanding physically impossible actuator rates. Enforcing a readiness safety floor on fixed-geometry symmetric platforms further encounters a zero-sum degeneracy: motor-speed redistribution cannot improve authority without conceding wrench tracking. This paper uses active morphology to break the degeneracy, treating servo tilt as a geometric resource supplying authority-recovery directions unavailable to static rotors. We construct a configuration-dependent, motor-only readiness certificate - the log-volume of the reachable wrench-rate set - that explicitly excludes servo capacity, preventing a "ghost capacity fallacy" in which the certificate would falsely credit slow mechanical kinematic limits instead of collapsing accurately at motor saturation. The certificate is enforced as a Control Barrier Function (CBF) within a Unified Physical-Command Quadratic Program acting on motor torques and servo setpoints. Closed-loop simulations of an articulated octorotor under severe gust disturbances show classical allocators diverging and uncertified articulated allocators violating the safety floor, while the proposed CBF filter bounds the system state and preserves vehicle authority.

0.34

FAM-DQ: A Dual-Quadrotor-Based Fully Actuated Aerial Manipulator for High-Torque Interaction

cs.RO ·2026-08-13 ·Xuwei Yang, Ruoyu Ren, Ziqian Guo
similarity 0.67
Abstract · 7 pages, 7 figures

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

0.07

Residual Wrench Certification and Margin-Aware Control Synthesis for Aerial Physical Interaction

cs.RO eess.SY ·2026-09-30 ·Abhimanyu Khadga, Abhinav Sinha, Shashi Ranjan Kumar
similarity 0.66
Abstract

We develop a task-relative framework for certifying residual wrench authority after hover and contact loading in multirotors with bounded actuators. Using convex geometry, we derive signed margins for prescribed convex reserves, including Euclidean balls and weighted ellipsoids. We obtain computable reserve certificates from actuator-interiority bounds to support slack-maximizing allocation. To preserve the required reserve, we propose command projection onto a tightened feasible set. We then connect the available reserve to structured gain synthesis and certify a local tracking region that respects actuator limits. Within this region, we establish nominal exponential convergence and robust ultimate boundedness. For the prescribed task and morphology family, we show that the optimized octarotor attains a larger margin than the optimized hexarotor at equal total thrust. We evaluate the proposed framework in closed-loop simulations of sustained rigid-wall contact using a fixed-geometry octarotor and a variable-tilt quadrotor with matched installed thrust. The quadrotor's local certificate admits a higher normalized push limit for the prescribed task family. In tests beyond the realizability boundaries, we observe the predicted loss of authority through rotor-thrust limits for the octarotor and tilt-servo limits for the quadrotor.

0.17

Dual Path Following for an Aerial Manipulator Under State and Input Constraints via Transverse Feedback Linearization

cs.RO eess.SYmath.OC ·2026-11-01 ·Hamza Tariq, Adeel Akhtar
code/data similarity 0.62
Abstract · 8 pages, 3 Figures

This paper studies dual path following for a quadrotor carrying a three-degree-of-freedom arm. The center of mass of the combined system must follow a vehicle path and the end effector must follow a second path, while the arm respects its joint limits and avoids its singular postures. The vehicle and the arm are mechanically coupled, so one controller must handle both paths. With the center of mass and the end-effector path coordinates as outputs, and a dynamic extension of the thrust, the system admits a normal form without internal dynamics. We characterize the states where this normal form fails. We formulate the transverse feedback linearizing controller as a quadratic program that relaxes only the speed of the end effector along its path and imposes safety and actuator limits as inequality constraints. The program reduces to a scalar problem with a closed-form solution. If it remains strictly feasible for all time, the feedback is locally Lipschitz, both paths are invariant and attractive, and every constraint holds. In the physics engine Drake, the controller resolves a conflict between the two speed references by slowing the end effector while both paths remain invariant. By contrast, a cascade with a safety filter leaves both paths. Code and animations are available at https://gradslab.github.io/am_dual_pf-/

0.22

Emergent Underactuation in Fully Actuated Multirotors by Minimizing a Homogeneous Allocation Cost

cs.RO eess.SYmath.OC ·2026-10-03 ·Antonio Franchi, Barbara Bazzana
similarity 0.62
Abstract

Full actuation is commonly valued for independent position and attitude tracking. This work establishes a complementary principle: when only a position trajectory is prescribed, minimizing a positively homogeneous allocation cost selects underactuated-like behavior on a fully actuated multirotor. This cost class includes norms and power laws, including standard minimum-norm pseudoinverse allocation. We use fiberwise infimization to transport the actuator-output cost to wrench space, yielding a homogeneous infimal allocation cost. Restriction to unit zero-moment forces defines a directional landscape whose minimizing directions are independent of force magnitude. We show that aligning any fixed minimizing direction with the required world-frame force minimizes instantaneous and integrated zero-moment allocation costs. The resulting body force remains in a fixed one-dimensional subspace without transverse components. We derive an exact optimality-gap decomposition quantifying the additional cost of every other attitude trajectory and characterizing the minimum-cost class. When a disturbance or prescribed-motion change modifies the required-force direction, a fully actuated platform can immediately generate the modified force using transverse authority and reorient toward the new minimum-cost family. A structurally underactuated platform must reorient before generating that force. Thus, homogeneous allocation-cost minimization explains why optimal nominal motion can be underactuated-like, while full actuation remains valuable for disturbance rejection and transient force generation.

0.26

Safety-Critical Bilateral Teleoperation for Omnidirectional Aerial Manipulation Using Force-Sensorless Haptic Feedback

cs.RO ·2026-08-22 ·Yubin Kim, Jinwoo Lee, Yongjun You, H. Jin Kim, Jeonghyun Byun
published similarity 0.61
Abstract · 8 pages, 10 figures. Accepted to the 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2026)

This paper presents a safety-critical bilateral teleoperation framework for omnidirectional aerial manipulators that integrates visual and force-sensorless haptic wrench feedback. Unlike existing approaches that either rely on onboard force/torque sensors or use model-dependent wrench estimates, which may become unreliable under model uncertainties or induce unintended feedback during free-flight, our method implements a hierarchical safety filter based on control barrier functions to avoid such limitations. The safety filter, being the key contribution, explicitly accounts for tracking errors arising from physical interaction between the aerial manipulator and its surroundings while enforcing thrust limits, a factor overlooked despite its critical importance for flight safety. This safety filter adjusts the command from the operator to ensure safe and stable aerial manipulation and avoid motor saturation. The adjustment made by the filter is mapped to haptic feedback, which is intuitive to the operator and conveys information on physical interaction and impending motor saturation. By actual experiments with a hexarotor-based omnidirectional aerial manipulator, we demonstrate that the proposed method avoids haptic feedback during free-flight, provides directionally consistent feedback under physical interaction, and can be operated for diverse manipulative tasks. Moreover, an ablation study further shows that the saturation filter improves interaction stability by explicitly preventing motor saturation and informing the operator of corrective actions.

0.37

Observer-Based Robust Control for an Aerial Manipulator System under Unknown External Disturbances

eess.SY ·2026-09-07 ·Mayank Pandey, Sneha Gajbhiye
similarity 0.61
Abstract

This paper addresses the mathematical modeling and control of an aerial manipulator system comprising a quadrotor as the uncrewed aerial vehicle and a robotic arm as the manipulator. The dynamic model is established by identifying the overall center-of-mass velocity and the system's orientation as constraints, yielding a simplified, two-decoupled subsystems: a locked (overall translation) subsystem and a shape-space (actuation or overall rotation) subsystem, both subjected to external disturbances. Since the system is mechanically coupled, a critical challenge arises where constant bounded disturbances in the first subsystem manifest as time-varying, state-dependent disturbances in the second subsystem. Given that the quadrotor is inherently unstable, the movement of the robotic manipulator (RM) during flight can further jeopardize the stability of the entire QRM system if these disturbances and coupling effects are not effectively managed. To address this, we present a continuous nonlinear disturbance observer-based feedback control law, which enables the independent control of each subsystem while systematically eliminating cross-coupling effects. The efficacy of the proposed controller is validated through multiple simulations emulating practical operating conditions, thereby substantiating its real-world applicability and highlighting the core contributions of this work.

0.11