CS Paper Radar

Modeling and Analysis of Dynamic Coupling Effects in a Free-Floating Space Manipulator

Erik Chumacero-Polanco

eess.SY ·submitted 2026-10-15 18:54 UTC · v1

Abstract

Motion of a robotic manipulator mounted on a free-floating spacecraft induces base translation and rotation, creating a dynamic coupling that affects end-effector motion. This paper characterizes that coupling in a planar three-link space manipulator. Using momentum conservation, velocity mappings are developed between manipulator joints, the end effector, and the spacecraft base. Singular value decomposition is then used to examine coupling strength, directional anisotropy, and the orientation of the coupled motions. Numerical maps show that coupling strength is invariant to the first joint angle but depends strongly on the relative configuration of the remaining joints. Increasing the spacecraft base mass reduces joint-to-base and end-effector-to-base coupling, while its effect on the joint-to-end-effector mapping is smaller and more dependent on configuration. The translational end-effector-to-base mapping is highly anisotropic in some configurations: its base-velocity ellipse becomes increasingly flattened as the weak coupling mode approaches zero. The principal end-effector and base velocity directions also change their relative alignment across the configuration space, producing predominantly opposing responses in some regions and transverse or approximately codirectional responses in others. Together, these results provide a geometric description of how coupling magnitude and direction vary with manipulator configuration and spacecraft mass.

Comment
30 pages, 12 Figures, double line

Closest papers

Nearest neighbours by meaning across the whole index.

Multi-Axis Selective Decoupling Framework for Free-Floating Space Manipulators

cs.RO physics.space-ph ·2026-08-14 ·Daegyun Choi, Donghoon Kim
similarity 0.66
Abstract · 11 pages, 7 figures, 2026 AAS/AIAA Astrodynamics Specialist Conference

Free-floating space manipulator systems face operational challenges due to dynamic coupling. While traditional reactionless manipulation eliminates base disturbances, enforcing the null-space projections across all rotational axes imposes excessive constraints on the system and drastically reduces the available workspace. To address this limitation, this work proposes a multi-axis selective decoupling framework that nullifies momentum transfer exclusively along mission-critical directions. By leveraging a directionally constrained sub-coupling matrix, the framework relaxes the null-space constraints. Numerical simulations confirm that this approach mathematically eliminates constrained directional disturbances along the targeted axes while preserving the remaining degrees of freedom, enabling the manipulator to execute task-space operations successfully.

0.10

State estimation for a hybrid rigid-continuum space manipulator system

cs.RO ·2026-10-27 ·Lorenzo Ticozzi, Patricio A. Vela, Panagiotis Tsiotras
similarity 0.54
Abstract · 10 pages, 9 figures. Version submitted to "Soft Robotics"

Spacecraft-mounted robotic manipulators can support long-term operability of orbiting assets by conducting tasks such as on-orbit assembly, repair, upgrade, and refueling. In this context, the integration of continuum/soft robotic mechanisms into space manipulator designs promises to reduce stowage volume and mass, as well as to improve operational safety through the inherent mechanical compliance of soft structures. This work presents a novel state reconstruction pipeline for a hybrid soft-rigid space manipulator, in which the distal link is a tendon-driven continuum robot. The estimation problem is formulated as a maximum a posteriori (MAP) inference problem over the hybrid manipulator's configuration, conditioned on discrete, noisy measurements from joint encoders and a vision-based sensing pipeline. The resulting soft-constrained optimization problem is transcribed as a factor graph, providing a compact representation for fusing heterogeneous measurements with the rigid-soft kinematic model. Furthermore, the adoption of the Geometric Variable Strain (GVS) approach yields a minimum-order parameterization of the configuration, a property expected to facilitate model-based feedback control design in future work. The proposed implementation is validated in simulation on a closed-loop trajectory where, for better realism, position measurements for the continuum link are obtained by means of a simulated visual pipeline leveraging synthetic photorealistic images. The state reconstruction accuracy and computational performance confirm the potential of the proposed framework for hybrid soft-rigid robotic applications in orbit.

0.35

Efficient Bezier Velocity Optimization for Free-Floating Space Manipulators

cs.RO ·2026-09-25 ·Duo Zhang, Zhizhuo Zhang, Xiaoli Bai, Jingjin Yu
similarity 0.53
Abstract

We present FAVOR (Free-floating Arm Velocity Optimization with Recursive Sensitivities), a planner for collision-free reaching, tracking, and prescribed-time pre-grasp interception on an unactuated spacecraft. It optimizes Bezier joint-velocity curves with linear velocity, acceleration, and continuity constraints. Decision dimension is independent of rollout resolution. Analytical recursive sensitivities provide task and clearance gradients through the coupled base-arm motion. Parallel evaluation, caching, and incremental collision discovery reduce computation. With a seven-DoF arm and five simulated spacecraft models, FAVOR achieves 99.8% point-to-point success with 1.779 s mean computation, versus 62.9% and 50.270 s for an IK-initialized position-spline baseline. Means include failures and timeouts. FAVOR completes 30 of 36 tracking cases, versus 15 for single-step QP, and all 36 interception instances, versus 22 for the spline baseline. A controlled ablation shows that finite differences increase mean planning time 4.7-fold.

0.23

Joint-Angle Invariance of Jacobian-Based Performance Indices for Serial Robotic Manipulators

cs.RO ·2026-10-21 ·Yaohua Zhou, Mingdao Lin, Jiayu Song, Xixin Zhao, Haidong Huang +2 more
published similarity 0.52
Abstract · 9 pages, 6 figures, 4 tables. Accepted at the 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2026)

This article investigates the joint-angle invariance (JAI) of Jacobian-based performance indices for serial robotic manipulators. We identify kinematic conditions under which representative performance indices, including manipulability, stiffness, and other Jacobian-derived indices, remain independent of the first and last joint angles. This property allows a systematic reduction in the effective configuration-space dimensionality, thereby simplifying the performance evaluation. The utility of JAI is demonstrated through two application scenarios: workspace performance map construction and task layout optimization. Comparative results show that the proposed JAI-based strategy reduces computational effort and storage requirements without compromising the effectiveness.

0.37

An Experimental Study of Downwash Effects on a Continuum Manipulator Integrated with a Multirotor UAV

cs.RO ·2026-08-19 ·Anuraj Uthayasooriyan, Krishna Manaswi Digumarti, ernando Vanegas, Felipe Gonzalez
top venue similarity 0.51
Abstract · Accepted to publish in Robotics and Automation Letters

Continuum arm aerial manipulation systems leverage soft-manipulator compliance and dexterity for tasks in confined or hazardous environments, but propeller downwash can degrade performance, particularly near walls and the ground. This effect remains uncharacterized for continuum manipulators. This letter experimentally studies downwash-induced kinematic deviations of a tendon-driven continuum manipulator integrated with a multirotor platform. Under still-air conditions, the CM is compared with a constant-curvature (CC) model. Downwash- induced end-effector pose deviations are then quantified relative to the mean still-air experimental baseline at four propeller throttle levels in free space, and at maximum throttle near a wall, and near the ground. Vertical position and yaw show the largest deviations and are amplified by ground effect. A CC-guided Gaussian process regression (GPR) residual model is learned from experimental data that improves forward pose prediction RMSE (position by 89-95%, orientation by 47-79%), and support compensation-oriented, downwash-aware modeling of continuum arm aerial manipulation systems.

0.70

Effector-Centric NMPC of Tiltable-Multirotors for Offset-Free Omnidirectional Aerial Manipulation

cs.RO ·2026-08-18 ·Jinjie Li, Yicheng Chen, Johannes Kübel, Haokun Liu, Junichiro Sugihara +1 more
top venue similarity 0.51
Abstract · 22 pages, 26 figures. Accepted to IEEE Transactions on Robotics (T-RO). This arXiv version includes a two-page appendix with additional impl…

Aerial manipulation extends robotic operations to previously inaccessible aerial environments. Unlike arm-equipped aerial systems, tiltable-multirotors can directly generate six-degree-of-freedom wrenches through their flight bases, enabling both efficient movement and omnidirectional operation by tilting the thrust direction. This work presents a design analysis and a wrench-based control framework for tiltable-multirotors in aerial manipulation. We show that a four-rotor tiltable configuration provides a balance between interference-free propeller sizing and hovering efficiency across different attitudes, and its null-space redundancy is crucial for traversing singular configurations under physical constraints. We further show that an upward end-effector placement yields a favorable trade-off between geometric clearance and available wrench. To address disturbances, we propose a dual strategy consisting of a modified integral term for model error and an acceleration-based estimator for external wrenches. Building on these insights, we develop an effector-centric nonlinear model predictive control (NMPC) framework that integrates design choices, singularity handling, and disturbance compensation into a unified formulation. The proposed framework runs fully onboard at 100 Hz on a custom-built tiltable-quadrotor. Real-world experiments, including a 90-deg step cartwheel rotation, whiteboard pushing, and continuous 360-deg valve turning, demonstrate the feasibility of wrench-based omnidirectional manipulation with singularity traversal on a one-DoF-per-arm tiltable-quadrotor.

0.51

Differentiable Hydrodynamics for Whole-Body MPC of Underwater Robots

cs.RO ·2026-11-19 ·Hefan Wang, Yvan Petillot, Carlos Mastalli
similarity 0.50
Abstract

Underwater vehicle-manipulator systems distribute actuation across thrusters and joint motors. Whole-body model predictive control (MPC), rather than separate vehicle and arm controllers, can coordinate both to extend the workspace and exploit the system's full kinematic capability. Doing so, however, requires a hydrodynamic model and derivatives throughout the prediction horizon. Computational fluid dynamics (CFD) captures geometry-dependent forces and moments for such a model, but is too expensive to evaluate online. We present a differentiable analytical hydrodynamic model combining smooth spherical-harmonic force and moment fields with a coupled added-inertia matrix identified from CFD. It compactly represents velocity and acceleration-dependent loads and provides their derivatives in closed form. These derivatives are propagated through free-floating vehicle--manipulator dynamics for whole-body trajectory optimization and receding-horizon control, jointly optimizing thruster forces and joint torques for reaching and continuous tracking. Held-out CFD tests validate the principal translational-force and rotational-moment fields and the added-inertia response. The analytical Jacobians evaluate faster and avoid the step-size sensitivity of central finite differences. Closed-loop Stonefish experiments demonstrate whole-body MPC in an independent marine simulator. By making geometry-dependent hydrodynamics directly available to gradient-based control, the model incorporates water forces and their sensitivities into motion allocation between the vehicle and arm, rather than treating them only as disturbances.

0.42

Preserving Operator Intent Under Actuation Constraints: Teleoperation of Manipulators with Coupled Transmissions

cs.RO ·2026-10-21 ·Xuhan Miao, Zijin Han, Yutong Shen, Haidong Huang, Shanliushui Gao +3 more
published similarity 0.50
Abstract · 6 pages, 5 figures. Contribution to the IROS 2026 workshop "5th Sensorimotor-Augmented Teleoperation: Human-Interaction-Oriented Paradigm an…

Teleoperation enables intuitive control of remote engineering robots for precision tasks. Existing direct joint-mapping methods have two limitations: independent motor saturation disrupts pitch-roll coordination in differential wrists, while fixed mappings struggle with abrupt tracking changes caused by gravitational loads and actuation constraints. We propose an actuator-constraint-aware leader-follower teleoperation method that jointly models leader gravity compensation, leader-follower joint mapping, and follower differential-wrist control. Specifically, we perform coordinated saturation in motor space according to the available gravity margin and integrate continuous angle unwrapping, feedback-state monitoring, and feasible-reference updates. This preserves the operator's motion direction, reduces coordination distortion, and suppresses recovery transients during saturation or brief communication failures. Real-robot experiments demonstrate smoother wrist trajectories and more continuous recovery than direct mapping.

0.30