CS Paper Radar

Cryogenic Recharacterization of a Commercial 22 nm FD-SOI Foundry Standard-Cell Library

Mohamed Gharib, Rami Rasheedi, Salma Abdelzaher, Henry Shi, Mike Hammer, Llorenç Fanals-i-Batllori, Aldo Pena Perez, Antonino Miceli, Inna Partin-Vaisband

cs.AR quant-ph ·submitted 2026-10-18 19:37 UTC · v1

Abstract

Wiring and bandwidth bottlenecks between a quantum processor and room-temperature electronics can be reduced by placing digital control at the cryogenic stage, but commercial foundry standard-cell libraries are not specified for operation at 4 K. A cryogenic recharacterization flow is therefore developed for a commercial 22 nm FD-SOI foundry standard-cell library using commercially available cryogenic compact-device models, while retaining the original cell circuits, layouts, logic functions, and implementation semantics and remaining compatible with the commercial synthesis, place-and-route, and signoff methodology used at room temperature. Body-bias dependence is quantified over 38,640 matched slew/load points at zero, +/-0.9 V, and +/-1.8 V body bias. Relative to full bias, zero-bias operation increases the median rising and falling delays by 38.6x and 33.0x, while approximately 90% of transitions exceed the foundry-defined maximum-transition envelope. The 0.8 V-to-0.4 V level shifter is even more sensitive to body bias: its worst-case falling delay decreases from 30.6 ns at zero bias to 0.56 ns at +/-1.8 V. For the outbound 0.4 V-to-0.8 V crossing, driving the 0.8 V receiver without a level shifter dissipates 57.7 uW of static power per bit at full bias, against 0.196 nW when level-shifted. In post-route analysis of the unchanged extracted physical database of a fabricated 32-bit ALU, the register-to-register setup boundary increases from 1.3 MHz at zero bias to 37.9 MHz at +/-0.9 V and 132.9 MHz at +/-1.8 V.

Comment
Submitted to the 2027 IEEE International Symposium on Circuits and Systems (ISCAS 2027)

Closest papers

Nearest neighbours by meaning across the whole index.

JFS-CryoMem: A Cryogenic Memory with Voltage-Controlled Superconducting Devices and Femtojoule-Scale Write/Read Energies

cs.ET cond-mat.supr-con ·2026-09-27 ·Md Rahatul Islam Udoy, Md Mazharul Islam, Juan P. Mendez, Denis Mamaluy, Aaron J. Muhowski +5 more
similarity 0.56
Abstract

Scalable cryogenic systems require memory that combines nonvolatile storage, selective access, low thermal disturbance, and compatibility with superconducting electronics. We present a cryogenic memory architecture that integrates a voltage-controlled Josephson junction field-effect transistor (JJFET) selector with a ferroelectric superconducting quantum interference device (FeSQUID) storage element, hereafter termed JFS-CryoMem. The JJFET provides gate-controlled cell selection, whereas the FeSQUID stores information in stable remanent-polarization states. JFS-CryoMem features separate read and write path mechanisms that support nondestructive readout and independent optimization of programming and sensing conditions. The architecture is evaluated using experimentally calibrated compact models that reproduce the measured electrical characteristics of both constituent devices. We demonstrate selective programming using a half-bias scheme, nonvolatile state retention, and distinguishable readout in a $4 \times 4$ array while accounting for the selected cell and all unselected parallel branches. We then extend the analysis to arrays up to $16 \times 16$ and examine how array scaling alters current distribution, column-equivalent resistance, readout separation, required bitline current, and read energy. The results reveal the principal sensing and energy tradeoffs associated with larger arrays and identify the operating conditions required to preserve read distinguishability as the array grows. JFS-CryoMem provides a device-to-array framework for cryogenic memory in quantum, high-performance, and space-oriented computing systems.

0.16

Highly Scalable Selectorless Cryogenic Memory Array Using Ferroelectric Josephson Field-Effect Transistors

cs.ET ·2026-09-25 ·Saheeb Ahmad, Shamiul Alam
similarity 0.53
Abstract · 8 pages, 4 Figures, 1 Table

Scalable memory systems that satisfy the temperature, speed, and energy requirements of cryogenic environments are essential for the development of large-scale quantum computers. They may also benefit high-performance computing and space applications. However, existing cryogenic memory technologies often suffer from limited scalability, low operating speed, and/or high power consumption, restricting the scalability of target applications. Ferroelectric Josephson field-effect transistors (Fe-JoFETs), which combine ferroelectric polarization with the superconducting properties of Josephson junctions, offer a promising solution. The ferroelectric layer enables nonvolatile storage capability, while the Josephson junction supports high-speed, energy-efficient operations. In this work, we leverage Fe-JoFETs to develop a highly scalable, ultra-low-power, nonvolatile cryogenic memory array that does not need additional selector devices for random access. Moreover, the superconducting component of Fe-JoFET provides a binary decision during read, eliminating the need for sensing peripheral circuitry. We first develop a physics-based Verilog-A compact model for Fe-JoFETs and use it to verify the functionality of the proposed memory array. By eliminating both selector and sensing circuitry, the proposed memory architecture offers higher scalability than existing technologies. The ultra-low-power operation of this memory also makes it compatible with strict power budgets of cryogenic applications.

0.35

Adaptive carrier signal synthesis for frequency-division multiplexed cryogenic detector readout

eess.SP physics.ins-det ·2026-11-12 ·Timo Muscheid, Benedikt Keppner, Daniel Crovo, Robert Gartmann, Marvin Fuchs +3 more
unusual similarity 0.50
Abstract · TWEPP26 Proceedings

Frequency-domain multiplexing is a fundamental technology for readout of cryogenic detector arrays on a single transmission line. Synthesizing a large number of static carrier tones for resonator stimulation eventually drives the cryogenic low-noise amplifier beyond its P1dB, introducing detector signal distortion. Scaling array sizes to O(10^6) detector pixels therefore demands minimizing the total power on the transmission line by continuous tracking of the resonances, which requires the readout electronics to be capable of updating the carrier tones dynamically. This work presents an scalable FPGA-based implementation for carrier signal synthesis based on a numerically controlled oscillator and a polyphase filter bank, enabling real-time frequency adaptivity as well as frequency resolution of 4 mHz to precisely tune the operating point, while simultaneously reducing resource usage compared to the current memory-based implementation.

0.32

Compute Before You Digitize: ADC-less Mixed-Signal Processing for Scalable Cryogenic Qubit Readout

cs.AR quant-phcs.ETeess.SP ·2026-11-17 ·Qirui Zhang, Ben Toby, He Wang, Benjamin Lienhard, David Blaauw +1 more
similarity 0.49
Abstract

We introduce DIRAC, an ADC-less in-cryostat qubit readout architecture that uses analog computing to redraw the analog-digital boundary. Directly operating on the front-end's analog output, passive complex mixers perform the equivalent of digital demodulation, ping-pong active-RC integrators average their outputs into down-sampled per-qubit traces, and a time-domain stage digitizes them, eliminating Nyquist-rate ADCs. A TX-RX co-design derives the mixers' local oscillators from the readout transmitter's baseband rather than per-tone PLLs. A per-line calibration flow trains the matched filter jointly with the neural network, improving fidelity and enabling low-bit-width, low-voltage digital processing. Designed in 22 nm FD-SOI and evaluated at 4 K on 1.12M experimental shots, DIRAC matches the fidelity of a floating-point (FP32) digital pipeline for readout windows down to 750 ns, at 31.6$\times$ and 238$\times$ lower energy than the fixed-point (FxP) and FP32 pipelines. It cuts the total 4 K power per physical qubit by 50.4% and 68.6% relative to FxP and room-temperature flex cables, respectively. At a fixed logical-qubit count and 4 K budget, this yields, against FxP, a code distance larger by 2 to 6 and a 1.6-7.3$\times$ (Willow) and 4.9-204$\times$ (SI1000, $p = 10^{-3}$) lower logical error rate.

0.23

SLICE-CiM: Selective Layer-wise Inference Control Engine with Confidence-Based Early Exit for SRAM based Digital Compute-in-Memory

cs.AR cs.NE ·2026-10-27 ·Pratham Sharma, Mohd Faisal Khan, Santosh Kumar Vishvakarma
similarity 0.48
Abstract

Digital SRAM compute-in-memory (CIM) macros enable energy-efficient CNN inference by eliminating off-chip weight transfers; however, peripheral control logic introduces three inefficiencies: bit- slice over-activation at reduced precision (L1), unnecessary accumula- tion depth (L2), and idle precision-transition stalls (L3). To address these, we present four synthesizable peripheral blocks: a Flush-Merge Enable (FME) controller, a Confidence-Based Early-Exit (EE) module, a Precision Register with Decoder (PR/PD), and a Bit-Serial Cycle Controller (CC), co-designed to minimize switching activity, wordline overhead, and leakage. Implemented in TSMC 65-nm CMOS at 335 MHz, the peripheral framework occupies 1769.760 μm2 post-synthesis and 1982.131 μm2 post-PnR. Gate-level VCD analysis reports 6.0706 μW leakage and 288.2902 μW (post-synthesis) / 322.8850 μW (post-PnR) dynamic power, totaling 328.9556 μW (0.2402% of system power). The EE module dominates dynamic power (58.2%), while WLG dominates area (58.1%). System evaluation on MobileNetV2 (CIFAR-100) shows efficiency scaling from 31.35 TOPS/W (8b/8b, 1.2 V) to 454.91 TOPS/W (2b/8b, 0.8 V), achieving 13.33x improvement without bitcell modification or retraining. The framework targets CNN workloads exploiting sparsity, with Transformer extension as future work.

0.34

Compute-in-Memory Attention: A Time-Domain Analog Softmax Circuit with RC-Tunable Temperature

cs.AR cs.LG ·2026-09-02 ·Ankur Singh, Ashish Gautam, Shruti R. Kulkarni, Guojing Cong
similarity 0.48
Abstract · 13 page, 16 figure

Softmax is a key operation in Transformer attention, but its exponentiation and normalization add significant overhead in compute-in-memory (CIM) accelerators, especially when analog attention scores must first be converted to the digital domain. This work presents a tunable-temperature analog softmax circuit in GlobalFoundries 22-nm fully depleted silicon-on-insulator (FDSOI) technology that operates directly on CIM-generated score voltages without intermediate analog-to-digital conversion. Each input score is converted into a time-domain event using a shared falling ramp. The corresponding comparator transition samples an RC-decaying reference to generate an exponential weight, which is then processed by an in-circuit normalization stage. In contrast to analog softmax circuits that rely on transistor weak-inversion behavior for exponentiation, the proposed architecture controls the softmax response through the ramp slope and RC time constant, enabling programmable effective temperature. The 128-element architecture is evaluated using transistor-level and post-layout extracted simulations, including multi-level input vectors, capacitance variation and mismatch, process and temperature variation, monte carlo analysis, and shared-interconnect parasitics. The complete 128-element implementation occupies 9453.42~$μ\mathrm{m}^{2}$ including the shared global ramp circuitry, while each replicated softmax element occupies 70.2~$μ\mathrm{m}^{2}$. The circuit achieves a 242.97-ns evaluation latency at 13.44~mW total power, corresponding to 25.5~pJ per output element. The simultaneous 128-element evaluation achieves an RMSE of 24.46~mV relative to the ideal softmax response. The extracted circuit characteristics are further incorporated into a MemTorch-based hardware-aware Transformer model, where the proposed softmax achieves a validation loss within 2.5\% of the ideal-softmax baseline.

0.30

An Open-Source Standard-Cell Library for IHP 130nm Developed by Students

cs.AR ·2026-09-24 ·Oscar Castañeda, Lavinia Recchioni, Tobias Senti, Flurin Cahenzli, Marco Ferroni +24 more
code/dataunusual similarity 0.46
Abstract · Submitted to a conference

Standard-cell libraries form the critical interface between transistor-level circuit design and automated digital design flows, yet their design and characterization are rarely covered in depth in digital VLSI courses. This paper presents VLSI 5, a graduate-level course at ETH Zurich in which students design, lay out, characterize, and integrate their own standard cells using IHP's open-source 130nm SG13G2 process design kit. In the first course offering, 19 students developed EZ130 8T, an open-source eight-track standard-cell library comprising 220 cells. We evaluate successive library versions using eight synthesis benchmarks, across which EZ130 8T achieves significant area reduction compared to the SG13G2 library at competitive timing. For a postlayout 8x8 matrix-vector multiplier, EZ130 8T reduces cell area by 35% and energy by 39% while maintaining virtually the same clock period. The library has already been adopted in other ETH Zurich VLSI courses, enabling the creation of chips entirely designed by students down to the transistor level.

0.38

Experimental Characterization of SMD Inductors for Cryogenic Power Conversion at 4 K

eess.SY ·2026-10-20 ·Rami Rasheedi, Umeshkumar Patel, Jonathan Baldwin, Antonino Miceli, Inna Partin-Vaisband
unusual similarity 0.46
Abstract

With the increasing complexity and scalability demands of cryogenic electronic systems, such as quantum computing platforms, conversion of power within the cryogenic environment has become a primary concern. Magnetic inductors are among the key components affecting converter performance, as their electrical and magnetic properties can change significantly at low temperatures. In this paper, five commercially available Vishay SMD power inductors are experimentally characterized down to 4 K: DC resistance is measured continuously during cooldown, while frequency-dependent AC inductance and resistance are measured up to 2 MHz at both room temperature and 4 K. The results show substantial DC resistance reductions of 25x-58x at 4 K, while the inductance degrades by only about 5-5.5%. Although cryogenic operation slightly increases the AC resistance (due to the intensified skin effect) and raises core losses, converter-level analysis shows an inductor-only efficiency improvement of approximately 5.3-6.9 percentage points at 1 A, and up to 22.8 points at 3 A. The measured frequency-dependent impedance of each inductor is imported into Cadence and a complete single-phase 24 V-to-1 V buck converter with GaN power devices is simulated at 1, 2, and 3 A at 4 K. The full-converter efficiency at 4 K is shown to improve by 3.0-5.2 percentage points at 1 A and by up to 22.5 points at 3 A for the AC-characterized devices. These findings indicate that commercially available off-the-shelf power inductors remain operationally viable under cryogenic conditions and can simultaneously increase inductor efficiency and reduce the overall power loss in cryogenic power conversion systems.

0.24